(57) - INTERNATIONAL HARVESTER RECTANGULAR BALER (1/57-12/72) (00) - COMPLETE MACHINE Case Agriculture

Select section (00) - COMPLETE MACHINE Case:

(3) - INTRODUCTION

(4) - INTRODUCTION - CONTINUED

(A-01) - 57 BALER, TWINE AND WIRE, SERIAL NUMBER 501G AND UP

(A-02) - 57 BALER, TWINE AND WIRE, SERIAL NUMBER 501G AND UP

(A-05) - MAIN FRAME

(A-06) - HITCH

(A-07) - MAIN DRIVE SUPPORT

(A-08) - LEFT AND RIGHT WHEELS

(A-09) - LEFT BALE CHAMBER SIDE

(A-10) - RIGHT BALE CHAMBER SIDE

(A-11) - LOWER TENSION CHANNEL AND BALE CHAMBER EXTENSION

(A-12) - LIFTING JACK

(A-12[A]) - LIFTING JACK, 2598L UP

(A-13) - BOTTOM PLATE, PLUNGER STOP AND NEEDLE GUARDS

(A-14) - FLYWHEEL AND FLYWHEEL HUB

(A-14[A]) - CRANKSHAFT AND PITMAN

(A-15) - PLUNGER

(A-16) - FEED OPENING TOP SHEET

(A-17) - MAIN DRIVE

(A-18) - PACKER DRIVE

(A-19) - PACKER CRANK, FINGERS AND RELIEF

(A-20) - CROSS CONVEYOR PLATFORM

(A-21) - AUGER AND AUGER DRIVE

(A-22) - PICKUP CYLINDER AND DRIVE

(A-25) - PICKUP COVER

(A-25[A]) - PICKUP WHEEL, STEEL

(A-26) - PICKUP WHEEL, RUBBER, WHEN ORDERED

(A-27) - TWINE CHEST AND SUPPORT

(A-28) - TWO COIL WIRE CAN

(A-28[A]) - FOUR COIL WIRE CAN

(A-29) - TWINE NEEDLE GUIDES AND TWINE GUIDES

(A-29[A]) - WIRE NEEDLE GUIDES AND WIRE GUIDES

(A-30) - TWINE NEEDLES AND NEEDLE PITMAN

(A-30[A]) - WIRE NEEDLES AND NEEDLE PITMAN

(A-31) - KNOTTER BASE PLATE

(A-32) - TWISTER BASE PLATE AND DRIVE FRAME

(A-34) - KNOTTER AND KNOTTER SHAFT

(A-37) - TWISTER AND TWISTER SHAFT

(A-39) - KNOTTER OR TWISTER COVER

(A-39[A]) - BALE LENGTH CONTROL

(A-40) - WARNING LAMP BRACKET AND SOCKET

(A-41) - MANUAL TENSION DEVICE

(A-42) - HYDRAULIC BALE TENSION DEVICE, CHANNELS, HOSE AND DRIVE

(A-44) - HYDRAULIC BALE TENSION DEVICE, HYDRAULIC PUMP AND RESERVOIR

(A-45) - HYDRAULIC BALE TENSION DEVICE, HYDRAULIC JACK

(A-45[A]) - POWER TAKE-OFF ATTACHMENT HITCH

(A-46) - POWER TAKE-OFF ATTACHMENT, GEAR BOX AND PULLEY

(A-47) - POWER TAKE-OFF ATTACHMENT, DRIVE SHAFTS FOR 540 AND 1000 RPM

(A-49) - POWER TAKE-OFF ATTACHMENT, IDLER PULLEY AND LEVER

(A-50) - POWER TAKE-OFF ATTACHMENT, PLUNGER CRANK AND PULLEY SHIELDS

(A-51) - PARTS COMMON TO C-123 AND WISCONSIN ENGINES

(A-52) - ADDITIONAL PARTS FOR C-123 AND WISCONSIN ENGINES, BATTERY BOX AND ELECTRICAL CABLES

(A-53) - ADDITIONAL PARTS FOR C-123 ENGINE, ENGINE MOUNTS AND IDLER

(A-54) - ADDITIONAL PARTS FOR WISCONSIN ENGINE, ENGINE BASE AND PULLEYS

(A-55) - PLUNGER CRANK SHIELD, FOR ENGINE DRIVE BALERS

(A-55[A]) - FLYWHEEL SHIELD

(A-55[B]) - DUAL WHEEL

(A-56) - TRAILER HITCH

(A-56[A]) - BALE CHUTE

(A-57) - ENGINE SHUT-OFF ATTACHMENT, FIBER BAR TYPE, FOR WIRE BALER, WHEN ORDERED

(A-58) - ENGINE SHUT-OFF ATTACHMENT, PUSH BUTTON TYPE, FOR WIRE BALER, WHEN ORDERED

(A-59) - CENTRALIZED LUBRICATION, VALVES

(A-60) - CENTRALIZED LUBRICATION, FOR TWINE BALERS, VALVES, TUBING, AND FITTINGS

(A-62) - CENTRALIZED LUBRICATION, FOR WIRE BALERS, VALVES, TUBING, SLEEVES AND FITTINGS

(A-64) - CENTRALIZED LUBRICATION, PUMP, PUMP SUPPORT AND MISCELLANEOUS

(A-64[A]) - FUEL TANK AND CONNECTIONS

(A-65) - AIR CLEANER & CONNECTIONS

(A-66) - RADIATOR AND CONNECTIONS

(A-66[A]) - INSTRUMENT PANEL AND GOVERNOR CONTROL RODS

(A-67) - OIL PRESSURE INDICATOR AND CONNECTIONS

(A-67[A]) - GENERATOR AND CONNECTIONS 6 VOLT ELECTRICAL SYSTEM

(A-68) - GENERATOR AND CONNECTIONS, 12 VOLT ELECTRICAL SYSTEM

(A-69) - GENERATOR, DELCO REMY, 6 VOLT

(A-70) - GENERATOR, DELCO REMY, 12 VOLT

(A-71) - CRANKING MOTOR, DELCO REMY, 6 VOLT

(A-72) - CRANKING MOTOR, DELCO REMY, 12 VOLT

(A-73) - ELECTRIC STARTING, 6 VOLT ELECTRICAL SYSTEM

(A-74) - ELECTRIC STARTING, 12 VOLT ELECTRICAL SYSTEM

(A-75) - HOOD, SCREEN AND SUPPORTS

(A-76) - BELT PULLEY GEAR REDUCTION DRIVE UNIT