AVSPARE.COM
parts catalog

ACCUMULATOR GP-BRAKE 3967247 - Caterpillar



3967247 ACCUMULATOR GP-BRAKE Caterpillar parts 797F ACCUMULATOR
Rating:
79
Alternative (cross code) number:
CA3967247
396-7247
3967247
Caterpillar 3967247 ACCUMULATOR GP-BRAKE

Buy ACCUMULATOR GP-BRAKE 3967247 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 3967247:

TRUCK  797F   Caterpillar
  For full view, you need register

Information:


Table 1
Diagnostic Codes Table    
Description    Conditions which Generate this Code    System Response    
261-13 Engine Timing Calibration calibration required     The Electronic Control Module (ECM) detects a calibration offset of zero for the engine speed/timing sensor.     Default timing of zero is used. Timing can be off by 3 degrees.
The code is active.    The engine speed/timing sensor is calibrated with a two-step process. A new timing reference is calculated first. The reference is based on the signals from the transducer and the engine speed/timing sensor. Next, the new timing reference is programmed into the permanent memory of the engine ECM.The engine speed/timing sensor provides engine information to the ECM. The ECM powers the engine speed/timing sensor with 12.5 1.0 VDC. The sensor senses the tooth pattern on the timing reference gear that is attached to the left camshaft. As the timing gear rotates past the engine speed/timing sensor, a signal is generated in the sensor. This signal is sent to the ECM. The ECM uses this signal in order to calculate the engine position and the engine speed.A loss of the engine speed/timing signal causes the ECM to stop sending power to the fuel injectors.Calibration of the timing is required only after the following circumstances:
The ECM has been replaced.
The timing gear and/or the rear gear train have been adjusted.
The timing gear and/or the rear gear train have been replaced.Test Step 1. Check for an "ACTIVE" Diagnostic Code
Remove electrical power to the ECM.
Connect Caterpillar Electronic Technician (ET) to the service tool connector.
If a timing calibration sensor is not already installed on this application, install a timing calibration probe onto the engine:
Remove the timing calibration plug from the flywheel housing.
Examine the flywheel through the timing calibration hole. Ensure that the probe is not inserted into the timing pin hole. If necessary, rotate the engine.
Illustration 1 g03515697
(1) 6V-3093 Transducer Adapter
Install the 6V-3093 Transducer Adapter into the hole for the timing calibration at the flywheel.
Illustration 2 g03515699
(2) 6V-2197 Transducer
Insert the 6V-2197 Transducer through the 6V-3093 Transducer Adapter . Insert the transducer until contact is made with the surface of the flywheel. Adjust the transducer in order to provide a clearance of 0.9 mm (0.04 inch) between the flywheel and the tip of the transducer.
Do not install the timing calibration probe over the timing pin hole in the flywheel or damage will result.
Tighten the nut on the 6V-3093 Transducer Adapter .
Connect the 7X-1695 Cable As between the transducer and the timing calibration connector P26.
Restore electrical power to the ECM.
Start the engine. Allow the engine to exit cold mode operation.
Monitor the diagnostic codes on Cat ET. Check and record any diagnostic codes.Note: Wait at least 30 seconds in order for the diagnostic codes to become active.Expected Result:The 261-13 diagnostic code is the only code that is active.Results:
OK - The 261-13 is the only active code. A timing calibration must be performed on the engine. Proceed to Test Step 2.
Not OK - The 261-13 is not the only active code

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
797F Off-Highway Truck LAJ00001-UP (MACHINE) POWERED BY C175-20 Engine
797F XQ Off-Highway Truck WSP00001-UP (MACHINE) POWERED BY C175-20 Engine


Parts accumulator Caterpillar catalog:

1700235 ACCUMULATOR-REFRIGERANT
414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E, 450E, 450F, 5130B, 5230B, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B,...
1627450 ACCUMULATOR GP-HYDRAULIC
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
2000750 ACCUMULATOR GP-PILOT OIL
824K, 825K, 826K, D10T2, D5N, D6N, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R II, D8R II, D8T, D9T
3182532 ACCUMULATOR GP-BRAKE
770G, 770G OEM, 772G, 772G OEM, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 777G
1763900 ACCUMULATOR GP-REFRIGERANT
216, 226B, 226B3, 232B, 236, 236B, 236B3, 242B, 242B3, 246C, 247, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 259B3, 262C, 267, 267B, 268B, 272C, 277C, 279C, 287, 287C, 289C, 297C, 299C, 302.5C, 416C...
3654503 ACCUMULATOR GP-BRAKE
770G, 770G OEM, 772G, 772G OEM, 773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM
4I1536 ACCUMULATOR GP-HYDRAULIC
303, 303.5, 303.5C, 303.5E, 303C CR, 304, 304.5, 304C CR, 304E, 305, 305.5, 305.5E, 305C CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311, 311B, 311C, 311D...
2493862 ACCUMULATOR GP-BRAKE
120M, 120M 2, 12M, 12M 2, 140M, 140M 2, 14M, 160M, 160M 2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.