1548041 ACTUATOR AS-PARKING BRAKE Caterpillar parts
814F, 814F II, 815F, 815F II, 816F, 816F II, 950F, 950F II, 960F, 966F, 966F II, 970F
Rating:
Alternative (cross code) number:
CA1548041
154-8041
1548041
CA1548041
154-8041
1548041
Weight: 13 pounds 6 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1548041 Actuator for Model 814F/815F/816F/950F/960F/966F Braking System
CTP For Model 814F/815F/816F/950F/960F/966F CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP For Model 814F/815F/816F/950F/960F/966F CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP 1548041 Actuator for Model 814F/815F/816F/950F/960F/966F Braking System
CTP For Model 814F/815F/816F/950F/960F/966F CTP Braking System || Highly Efficient || Easy in-and-out fit
CTP For Model 814F/815F/816F/950F/960F/966F CTP Braking System || Highly Efficient || Easy in-and-out fit
Compatible equipment models: 1548041:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 9U-5023 Main Bearing Wrench 1
C 2P-5517 Main Bearing Tool 1
D 230-5843(1)
or
236-6688(2) Main Bearing Cap Tool 2
(1) Use with 19.0 mm (3/4 inch) main bearing cap bolts.
(2) Use with 22.2 mm (7/8 inch) main bearing cap bolts.Start By:
Remove the piston cooling jets.
Remove the oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00930577
Remove covers (1) from the side of the engine.
Use Tooling (A) to rotate the crankshaft. Rotate the crankshaft to position the counterweight on the top.
Illustration 2 g00930580
Use Tooling (B) and loosen the bolts for the main bearing cap.
Illustration 3 g00930589
Remove the two outer bolts for main bearing cap (2) and install Tooling (D). Install Tooling (D) until Tooling (D) bottoms out in the block. Adjust nuts (3) on Tooling (D) until nuts (3) make contact with main bearing cap (2). Remove the two inner bolts for main bearing cap (2).
Illustration 4 g00930593
Loosen nuts (3) evenly to lower main bearing cap (2). Lower main bearing cap (2) to the end of the bolt on Tooling (D) to gain access to the main bearings.
Illustration 5 g00930603
Use Tooling (A) and rotate the crankshaft until the oil hole of the crankshaft journal is just below the side of the main bearing without the tab. Install Tooling (C) and remove the upper bearing.
Illustration 6 g00930606
Remove lower main bearing (4) from main bearing cap (2).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1
B 9U-5023 Main Bearing Wrench 1
C 2P-5517 Main Bearing Tool 1
D 230-5843(1)
or
236-6688(2) Main Bearing Cap Tool 2
(1) Use with 19.0 mm (3/4 inch) main bearing cap bolts.
(2) Use with 22.2 mm (7/8 inch) main bearing cap bolts.Start By:
Remove the piston cooling jets.
Remove the oil pump.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00930577
Remove covers (1) from the side of the engine.
Use Tooling (A) to rotate the crankshaft. Rotate the crankshaft to position the counterweight on the top.
Illustration 2 g00930580
Use Tooling (B) and loosen the bolts for the main bearing cap.
Illustration 3 g00930589
Remove the two outer bolts for main bearing cap (2) and install Tooling (D). Install Tooling (D) until Tooling (D) bottoms out in the block. Adjust nuts (3) on Tooling (D) until nuts (3) make contact with main bearing cap (2). Remove the two inner bolts for main bearing cap (2).
Illustration 4 g00930593
Loosen nuts (3) evenly to lower main bearing cap (2). Lower main bearing cap (2) to the end of the bolt on Tooling (D) to gain access to the main bearings.
Illustration 5 g00930603
Use Tooling (A) and rotate the crankshaft until the oil hole of the crankshaft journal is just below the side of the main bearing without the tab. Install Tooling (C) and remove the upper bearing.
Illustration 6 g00930606
Remove lower main bearing (4) from main bearing cap (2).
Caterpillar parts catalog:
Parts actuator Caterpillar catalog:
9V8736
ACTUATOR GP-BRAKE
814B, 815B, 816B, 950F, 950F II, 966F, 966F II, 970F
814B, 815B, 816B, 950F, 950F II, 966F, 966F II, 970F
8N2503
ACTUATOR AS-GOVERNOR
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 215, 225, 229, 235, 235B, 3204, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 215, 225, 229, 235, 235B, 3204, 330, 330 FM L, 330 L, 3304, 3304B, 3306, 3...
3T5193
ACTUATOR ASSEM.
834B, 916, 926, 926A, 936, 936F, 950F II, 966C, 973, 980F, 988B, 992C, G936, IT12, IT18B, IT28, IT28B
834B, 916, 926, 926A, 936, 936F, 950F II, 966C, 973, 980F, 988B, 992C, G936, IT12, IT18B, IT28, IT28B
1485382
ACTUATOR AS-PARKING BRAKE
950F, 950F II, 960F, 966F
950F, 950F II, 960F, 966F
8R8545
ACTUATOR GROUP
950F, 966F, 970F
950F, 966F, 970F
1485382
ACTUATOR AS-PARKING BRAKE
950F, 950F II, 960F, 966F
950F, 950F II, 960F, 966F
3E8786
ACTUATOR
5130, 5130B, 515, 5230, 5230B, 525, 525B, 535B, 545, 988F, 988F II, 992D
5130, 5130B, 515, 5230, 5230B, 525, 525B, 535B, 545, 988F, 988F II, 992D
6V3661
ACTUATOR AS-SWITCH
988F, 988F II, 992D
988F, 988F II, 992D
1126163
ACTUATOR
320B, 322B LN, 325B L, 330B L, 330C, 345B II, 345B L, 5080, 994, PM-465, PM-565, PM-565B
320B, 322B LN, 325B L, 330B L, 330C, 345B II, 345B L, 5080, 994, PM-465, PM-565, PM-565B
3E8817
ACTUATOR
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 950G, ...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 950G, ...
1839033
ACTUATOR
950G, 950G II, 962G, 966G, 972G, 972G II
950G, 950G II, 962G, 966G, 972G, 972G II
1126159
ACTUATOR
785C, 789C, 793C, 950G
785C, 789C, 793C, 950G
1890789
ACTUATOR
950G, 950G II, 962G
950G, 950G II, 962G
1236386
ACTUATOR
992G
992G