ADAPTER-TIP 2238104 - Caterpillar

2238104 ADAPTER-TIP Caterpillar parts 980C, 980G, 980G II, 980H, 980K, 980M

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2238104
223-8104
2238104

Weight: 39 pounds 17 kg.

Buy ADAPTER-TIP 2238104 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

1969820-1 - Connector Housing, Positive Lock 250 Series, Receptacle, 1 Positions, (Pack of 250)

$204.00

09 Jun 2020

-: -

1969820-1 - Connector Housing, Positive Lock 250 Series, Receptacle, 1 Positions, (Pack of 250)
Product Range: Positive Lock 250 Series || Gender: Receptacle || No. of Positions: 1Positions || For Use With: AMP Positive Lock 250 Series 2825084, 2238104 & 2238139 Socket Contacts

1969820-1 - Connector Housing, Positive Lock 250 Series, Receptacle, 1 Positions, (Pack of 250) (1969820-1)

$204.00

02 Dec 2019

-: -

1969820-1 - Connector Housing, Positive Lock 250 Series, Receptacle, 1 Positions, (Pack of 250) (1969820-1)
Product Range: Positive Lock 250 Series || Gender: Receptacle || No. of Positions: 1Positions || For Use With: AMP Positive Lock 250 Series 2825084, 2238104 & 2238139 Socket Contacts

Show more prices Caterpillar parts

Number on catalog scheme: 5B

Caterpillar 2238104 Parts scheme ADAPTER-TIP

For full view, you need register

Compatible equipment models: 2238104:

WHEEL LOADER 980C 980G 980G II 980H 980K 980M Caterpillar

Information:

Improper jump start cable connections can cause an explosion resulting in personal injury.Prevent sparks near the batteries. Sparks could cause vapors to explode. Do not allow jump start cable ends to contact each other or the engine.
If the installation is not equipped with a backup battery system, it may be necessary to start the engine from an external electrical source.First, determine the reason that it is necessary to start with power from an external source.Many batteries which are considered unusable are still rechargeable. After jump starting, the alternator may not be able to fully recharge batteries that are severely discharged. The batteries must be charged to the proper voltage with a battery charger. For information on testing and charging, refer to the Special Instruction, SEHS7633, "Battery Test Procedure".
Using a battery source with the same voltage as the electric starting motor. Use ONLY equal voltage for jump starting. The use of higher voltage will damage the electrical system.Do not reverse the battery cables. The alternator can be damaged. Attach ground cable last and remove first.When using an external electrical source to start the engine, turn the generator set control switch to the "OFF" position. Turn all electrical accessories OFF before attaching the jump start cables.Ensure that the main power switch is in the OFF position before attaching the jump start cables to the engine being started.
Turn the start switch on the stalled engine to the OFF position. Turn off all accessories.
Connect one positive end of the jump start cable to the positive cable terminal of the discharged battery. Connect the other positive end of the jump start cable to the positive cable terminal of the electrical source.
Connect one negative end of the jump start cable to the negative cable terminal of the electrical source. Connect the other negative end of the jump start cable to the engine block or to the chassis ground. This procedure helps to prevent potential sparks from igniting combustible gases that are produced by some batteries.
Charge the batteries. The engine will not continue to run after starting if the batteries have not been charged.
Start the engine.
Immediately after the stalled engine is started, disconnect the jump start cables in reverse order.