parts catalog

ADAPTER GP-AIR CLEANER 2389380 - Caterpillar

2389380 ADAPTER GP-AIR CLEANER Caterpillar parts 3608, C280-16, C280-8 ADAPTER
Alternative (cross code) number:
Caterpillar 2389380 ADAPTER GP-AIR CLEANER

Buy ADAPTER GP-AIR CLEANER 2389380 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 2389380:

MARINE ENGINE  3608   C280-16   C280-8   Caterpillar
  For full view, you need register


Illustration 1 g01227326
Secondary brake solenoidThis diagnostic code is recorded when the current of the solenoid circuit is above normal. The secondary brake solenoid will not engage the brakes when the service brake pedal is pressed near the floor. Note: A problem with the secondary brake solenoid will not keep the service brakes from functioning. The function of the primary service brake is performed by the ECM by using the position sensor for the service brake pedal and the left and right brake solenoids. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely.Note: Ensure that CID 0722 FMI 06 is on hold and that the fault present indicator shows "SERV CODE". This procedure can cause new diagnostic codes to be recorded. Ignore these created problems. When the procedure is completed, clear the created problems. Test Step 1. CHECK THE SOLENOID
Turn the key start switch to the ON position. Ensure that the CID 0722 FMI 06 code is on hold.
Observe the status of the CID 0722 FMI 06 diagnostic code.
Disconnect the machine harness from the secondary brake solenoid. Expected Result:The active FMI 06 diagnostic code changes to an active FMI 05 diagnostic code when the solenoid is disconnected from the machine harness.Results:
YES - The active FMI 06 diagnostic code changes to a FMI 05 diagnostic code when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test step in order to verify the solenoid failure. Replace the solenoid.STOP
NO - The FMI 06 diagnostic code remains active. Disconnecting the solenoid did not affect the status of the active diagnostic code. Proceed to Test Step 2.Test Step 2. CHECK THE SIGNAL CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND
Turn the key start switch to the OFF position. The machine harness remains disconnected from the solenoid.
Turn the key start switch to the OFF position.
Disconnect the machine harness connectors J1 and J2 from the ECM.
At machine harness connector J1 or J2, measure the resistance from the solenoid signal contact J2-58 (wire F792-WH) to all of the other J1 and J2 contacts and to frame ground.Expected Result:Each resistance should be greater than 5000 ohms. Results:
OK - The machine harness is correct. Proceed to Test Step 3.
NOT OK - There is a short in the machine harness. The short is between signal wire F792-WH and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE STATUS OF THE DIAGNOSTIC CODE
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the key start switch to the ON position.
Enter service mode of the Caterpillar Monitoring System and clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and release the service brake pedal.
Determine if CID 0722 FMI

Cat SIS web machinery list:

Caterpillar parts catalog
C280–16 Marine Engine R4M00001-UP
C280-8 MARINE NDT00001-UP
C280-8 MARINE PKA00100-UP
C280-16 MARINE NKB00001-UP

Parts adapter Caterpillar catalog:

2136791 ADAPTER
3616, C280-12, C280-16, C280-6, C280-8, G3606, G3608, G3612, G3616
3606, 3608, 613C, 613C II, 615, 615C, 621, 621B, 621E, 623E, 627B, 627E, 631E, 633E II, 637D, 637E, 641B, 651E, 657E, C280-6, C280-8, C9, G3508, G3512, G3516
1090694 ADAPTER
3606, 3608, 3612, 3616, C280-12, C280-6
3606, 3608, C280-6, C280-8
3606, 3608, 3616, C280-16, C280-6, G3606, G3606B, G3608, G3616
2785291 ADAPTER
3612, 3616, C280-12, C280-16
3606, 3608, 3612, 3616, C280-12, C280-16, G3612, G3616
3542783 ADAPTER
C280-16, C280-8
3606, 3608, 3612, 3616, C280-16, C280-8
3606, 3608, 3612, 3616, C280-8
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.