3G6927 ADAPTER Caterpillar parts
416, 416B, 416C, 416D, 420D, 420E, 420F, 424B, 424B HD, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436, 436C, 438C, 438D, 442D, 442E, 444...
Rating:
Alternative (cross code) number:
CA3G6927
3G-6927
3G6927
CA3G6927
3G-6927
3G6927
Weight: 0.08 pounds 0 kg.
BACKHOE LOADER, TELEHANDLER,
Compatible equipment models: 3G6927:
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9S-9082     Engine Turning Tool     1    
B     5P-3526 (1)     Piston Ring Compressor     1    
200-3914 (2) Piston Ring Compressor     1    
C     8T-3052     Degree Wheel     1    
( 1 ) For use with 137 mm (5.4 inch) bores.
( 2 ) For use with 145 mm (5.7 inch) bores.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston.Note: Ensure that the connecting rod and pistons are installed in the correct cylinder.
Illustration 1 g01048560
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner.Note: Install the connecting rod so that the bearing tab is located on the side of the piston cooling jet.
Install the upper connecting rod bearing in the connecting rod.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Pull the connecting rod onto the crankshaft journal.
Install the lower connecting rod bearing in the connecting rod bearing cap.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Illustration 2 g01016640
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1) , as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Tighten Bolt (A) and Bolt (C) again to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (A) and Bolt (C) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     9S-9082     Engine Turning Tool     1    
B     5P-3526 (1)     Piston Ring Compressor     1    
200-3914 (2) Piston Ring Compressor     1    
C     8T-3052     Degree Wheel     1    
( 1 ) For use with 137 mm (5.4 inch) bores.
( 2 ) For use with 145 mm (5.7 inch) bores.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.
Apply clean engine oil to the cylinder liner bore, to the piston rings, and to the outer surface of the piston.Note: Ensure that the connecting rod and pistons are installed in the correct cylinder.
Illustration 1 g01048560
Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.
Use Tooling (B) to install piston (3) and the connecting rod in the cylinder liner.Note: Install the connecting rod so that the bearing tab is located on the side of the piston cooling jet.
Install the upper connecting rod bearing in the connecting rod.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Pull the connecting rod onto the crankshaft journal.
Install the lower connecting rod bearing in the connecting rod bearing cap.Note: Ensure that the connecting rod bearing is installed so that the bearing tab fits into the notch in the connecting rod.
Illustration 2 g01016640
Position connecting rod bearing cap (2) on the connecting rod.Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod. The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.
Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.
Tighten bolts (1) , as follows:
Tighten Bolt (A) and Bolt (C) to a torque of 70 4 N m (52 3 lb ft).
Tighten Bolt (B) and Bolt (D) to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (B) and Bolt (D) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Tighten Bolt (A) and Bolt (C) again to a torque of 70 4 N m (52 3 lb ft).
Turn Bolt (A) and Bolt (C) for an additional 60 5 degrees (1/6 turn).Note: If Tooling (C) is not used, place an index mark on each bolt.
Rotate the crankshaft in order to ensure that the crankshaft turns freely.End By:
Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets - Remove and Install".
Install the engine oil pump. Refer to Disassembly
Cat SIS web machinery list:
Parts adapter Caterpillar catalog:
1193205
ADAPTER-STRAP
303.5, 303.5D, 303.5E, 303E CR, 304C CR, 304D CR, 304E, 305.5E, 305C CR, 305E, 308E, 416B, 416C, 416D, 420D, 422E, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 432D, 432E, 434E, 436B, 436C, 438C, 442D, 4...
303.5, 303.5D, 303.5E, 303E CR, 304C CR, 304D CR, 304E, 305.5E, 305C CR, 305E, 308E, 416B, 416C, 416D, 420D, 422E, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 432D, 432E, 434E, 436B, 436C, 438C, 442D, 4...
1193204
ADAPTER-STRAP
416B, 416C, 416D, 420D, 422E, 424D, 426B, 426C, 428C, 428D, 428E, 432D, 432E, 434E, 436B, 436C, 438B, 438C, 442D, 442E, 444E
416B, 416C, 416D, 420D, 422E, 424D, 426B, 426C, 428C, 428D, 428E, 432D, 432E, 434E, 436B, 436C, 438B, 438C, 442D, 442E, 444E
5P6944
ADAPTER-STRAIGHT THREAD
10 FT, 10-20B, 10B, 120G, 120H, 120H ES, 120H NA, 120M 2, 12G, 12H, 12H NA, 12M 2, 130G, 135H, 135H NA, 140G, 140H, 140H NA, 140M 2, 14G, 14H, 14M, 160G, 160M 2, 16G, 16H, 16M, 205B, 214B, 216B3, 224B...
10 FT, 10-20B, 10B, 120G, 120H, 120H ES, 120H NA, 120M 2, 12G, 12H, 12H NA, 12M 2, 130G, 135H, 135H NA, 140G, 140H, 140H NA, 140M 2, 14G, 14H, 14M, 160G, 160M 2, 16G, 16H, 16M, 205B, 214B, 216B3, 224B...
1P6886
ADAPTER
1673C, 30/30, 3304, 3306, 3306B, 3306C, 416, 416B, 426B, 428, 436, 446, 446B, 508, 5130, 5130B, 515, 518, 5230, 5230B, 525, 525B, 527, 528, 535B, 545, 554, 571G, 572G, 583K, 594H, 613B, 615, 621E, 621...
1673C, 30/30, 3304, 3306, 3306B, 3306C, 416, 416B, 426B, 428, 436, 446, 446B, 508, 5130, 5130B, 515, 518, 5230, 5230B, 525, 525B, 527, 528, 535B, 545, 554, 571G, 572G, 583K, 594H, 613B, 615, 621E, 621...
9R2483
ADAPTER
416, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 446, 446B, 446D
416, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 446, 446B, 446D
8J7525
ADAPTER
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436C, 438, 438C, 931, 931B
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436C, 438, 438C, 931, 931B
5P8874
ADAPTER
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12K, 12M, 130G, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 14G, 14H, 14M, 160K, 160M, 16G, 16H, 16H NA, 225, 245, 245B, 24H, 24M, 272D XHP, 299D XHP, 30/...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12K, 12M, 130G, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 14G, 14H, 14M, 160K, 160M, 16G, 16H, 16H NA, 225, 245, 245B, 24H, 24M, 272D XHP, 299D XHP, 30/...
6V1722
ADAPTER
120G, 120H, 120M, 120M 2, 12G, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 140G, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14M, 160G, 160H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16G...
120G, 120H, 120M, 120M 2, 12G, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 140G, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, 14M, 160G, 160H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16G...
1959204
ADAPTER-TIP
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
9W5455
ADAPTER-VALVE
416, 416B, 426, 426B, 428, 436
416, 416B, 426, 426B, 428, 436
9R2483
ADAPTER
416, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 446, 446B, 446D
416, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 446, 446B, 446D
6I0817
ADAPTER
120M, 12M, 2470C, 3054, 3054B, 307, 312, 312C, 315B L, 320D GC, 320D L, 323D L, 416B, 416C, 420E, 426B, 426C, 428B, 428C, 430E, 436C, 438B, 438C, 450E, 553C, 559, 613G, 908, 914G, 924H, 924HZ, 928H, 9...
120M, 12M, 2470C, 3054, 3054B, 307, 312, 312C, 315B L, 320D GC, 320D L, 323D L, 416B, 416C, 420E, 426B, 426C, 428B, 428C, 430E, 436C, 438B, 438C, 450E, 553C, 559, 613G, 908, 914G, 924H, 924HZ, 928H, 9...
1013913
ADAPTER
3054, 3054B, 3056, 312, 312C, 416B, 416D, 424D, 426B, 428B, 438B, 554, AP-800C, BG-225B, BG-225C, CP-433C, CS-431C, M312, M315, PS-150B, PS-200B, TH103, TH350B, TH355B, TH460B, TH62, TH63, TH82, TH83
3054, 3054B, 3056, 312, 312C, 416B, 416D, 424D, 426B, 428B, 438B, 554, AP-800C, BG-225B, BG-225C, CP-433C, CS-431C, M312, M315, PS-150B, PS-200B, TH103, TH350B, TH355B, TH460B, TH62, TH63, TH82, TH83
7C2729
ADAPTER
212, 3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 424D, 426B, 426C, 428B, 428C, 436C, 438B, 438C, 554, 908, 914G, AP-800, CB-434B, CB-434C, CB-544, CB-545, CP-433E, CS-323, CS-4...
212, 3054, 3054B, 312, 312B L, 312C, 315, 315B L, 317, 416B, 416C, 416D, 424D, 426B, 426C, 428B, 428C, 436C, 438B, 438C, 554, 908, 914G, AP-800, CB-434B, CB-434C, CB-544, CB-545, CP-433E, CS-323, CS-4...
6I1052
ADAPTER
3054, 3054B, 3056, 312, 312C, 315, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 438D, 442D, 554, 908, 914G, CB-534B, CB-534C, CB-535B, CP-433C, CP-433E, CS-...
3054, 3054B, 3056, 312, 312C, 315, 317, 416B, 416C, 416D, 420D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 438D, 442D, 554, 908, 914G, CB-534B, CB-534C, CB-535B, CP-433C, CP-433E, CS-...
1488307
ADAPTER AS
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 14H, 14M, 160K, 160M, 16H, 24M, 272D XHP, 299D XHP, 303, 311C, 311D LRR, 312D, 312D L, 314D CR, 314D LCR, 315D L, 319D, 319D L, 319D LN, 365B, 420D, 4...
120K, 120K 2, 12K, 12M, 140G, 140K, 140K 2, 140M, 14H, 14M, 160K, 160M, 16H, 24M, 272D XHP, 299D XHP, 303, 311C, 311D LRR, 312D, 312D L, 314D CR, 314D LCR, 315D L, 319D, 319D L, 319D LN, 365B, 420D, 4...
7C8934
ADAPTER-FAN
3114, 3116, 3126, 446B, 446D, CB-434, RT100
3114, 3116, 3126, 446B, 446D, CB-434, RT100
1192942
ADAPTER
120H, 120H ES, 120H NA, 12M, 135H, 135H NA, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3176C, 3196, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL,...
120H, 120H ES, 120H NA, 12M, 135H, 135H NA, 140H, 140M, 143H, 14H, 160H, 163H, 16H, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3176C, 3196, 320B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL,...
8J7525
ADAPTER
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436C, 438, 438C, 931, 931B
416, 416B, 416C, 426, 426B, 426C, 428, 428B, 428C, 436, 436C, 438, 438C, 931, 931B
1035522
ADAPTER AS
416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
416B, 416C, 416D, 420D, 424D, 426B, 426C, 428B, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
6Y1142
ADAPTER AS
416, 416B, 426B, 428, 428B, 436
416, 416B, 426B, 428, 428B, 436