AVSPARE.COM
parts catalog

ADAPTER 3G7357 - Caterpillar


3G7357 ADAPTER Caterpillar parts 225D, 229, 229D, 325 LN, 966C, E240
Rating:
83
Alternative (cross code) number:
CA3G7357
3G-7357
3G7357
Caterpillar 3G7357 ADAPTER
Weight: 41 pounds 18 kg.

Buy ADAPTER 3G7357 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$239.95

20 Apr 2025

US: Parts ASAP
Bucket Tooth Adapter Cover fits Caterpillar 3G7357
Parts ASAP Replaces Caterpillar Mfg Number(s) 3G7357 || Series: J Series || Sub-Series: J350 Series
$98.95

03 Mar 2025
41.89[18.85] pounds
US: Parts ASAP
All States Bucket Tooth Adapter Cover fits Caterpillar 3G7357
All States Replaces Caterpillar Mfg Number(s) 3G7357 || Series: J Series || Sub-Series: J350 Series
$75.59

03 Mar 2025
41.89[18.85] pounds
US: National 1 Trac
Bucket Tooth Adapter Cover fits Caterpillar 3G7357
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Number on catalog scheme: None
  For full view, you need register

Compatible equipment models: 3G7357:

EXCAVATOR  225D   229   229D   325 LN   E240  
WHEEL LOADER  966C   Caterpillar

Information:


Table 2
Optional Tools (1)    
Tool    Part
Number    Description    Qty    
D     8T-0860     Pressure Gauge
0 to 40000 kPa (0 to 5800 psi)     1    
E     177-7860     Hose As     1    
F     6V-4143     Quick Connect Coupler     2    
G     6V-3989     Fitting     1    
( 1 ) The optional tools can be used in place of the digital pressure measurement tools which are specified in the required tool list.
Drive the machine to a smooth, horizontal surface.
Illustration 1 g02125547
Move propel lever (3) to the NEUTRAL position.
Rotate speed dial (2) to the MINIMUM position.
Move parking brake switch (1) to the ON position.
Illustration 2 g02125548
Move screed lift switch (4) to the FLOAT position. Move the screed lift switch on the right instrument panel to the FLOAT position.Note: The screed lift switch on both instrument panels must be in the FLOAT position in order for the screed to lower.
After the screed rests on the ground, move screed lift switch (4) to the HOLD position.
Illustration 3 g02125550
Move throttle control switch (5) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
After the engine reaches low idle, move engine start switch (6) to the OFF position.
Illustration 4 g02125552
Open access door (7) on the left side of the machine.
Illustration 5 g02125554
Remove cap from port "G" (8) on the left grade and slope control valve. Install Tool (C) on tap (9) .
Connect Tool (B) to Tool (C). Connect Tool (B) to Tool (A).
Move engine start switch (6) to the START position. Release the engine start switch when the engine starts.
Operate the engine at low idle for a few minutes.
Move throttle control switch (5) to the HIGH IDLE position. Hold the switch in this position for less than 1 second. The engine speed should increase to 2200 rpm.
Illustration 6 g02125557
Monitor the hydraulic oil temperature on the operator display. Operate the machine until the oil temperature reaches 43 5.6 °C (110 10 °F).
Read pressure on Tool (A). The pressure should be 14000 175 kPa (2030 25 psi).
Move throttle control switch (5) to the LOW IDLE position. Hold the switch in this position for less than 1 second.
After the engine reaches low idle, move engine start switch (6) to the OFF position.
If the pressure is within the specified range, go to Step 23. If the pressure is outside the specified range, go to Step 20.
Illustration 7 g02125561
Use a 4 mm hex wrench in order to loosen set screw (9) on the pump control valve.
Use a 6 mm hex wrench in order to manipulate adjustment screw (10). Rotate the adjustment screw clockwise in order to increase the pressure. Rotate the adjustment screw counterclockwise in order to decrease the pressure.Note: One revolution of adjustment screw (10) changes the pressure by approximately 2411 kPa (350 psi).
Hold adjustment screw (10) in place. Tighten set screw (9). Go back to Step 12.
Remove the tooling.
Close access door (8) .

Caterpillar parts catalog:

Caterpillar parts catalog
225B LC 229 EXCAVATORS 1GF00001-UP (MACHINE) POWERED BY 3208 ENGINE
229D EXCAVATOR 2LJ00001-UP (MACHINE) POWERED BY 3304 ENGINE
225D LC EXCAVATOR 6RG00001-UP (MACHINE) POWERED BY 3304 ENGINE
325, 325L, 325LN EXCAVATORS 2SK00001-UP (MACHINE) POWERED BY 3116 ENGINE
E240, EL240 HYDRAULIC EXCAVATORS 1FG00001-UP (MACHINE) POWERED BY 3304 ENGINE
966C WHEEL LOADER 30K02369-UP (MACHINE) POWERED BY 3306 ENGINE


Parts adapter Caterpillar catalog:

3G8354 ADAPTER
215, 225, 229
8E6464 ADAPTER-STRAP
229, 235B, 235C, 235D, 325 L, 325 LN
6I6406 ADAPTER-2 STRAP
231D, 320 L, 320B, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D2, 321C, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 323D L, 323D2 L, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325...
6I6404 ADAPTER-2 STRAP
231D, 320 L, 320B, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D2, 321C, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 323D L, 323D2 L, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325...
6I6405 ADAPTER-2 STRAP
231D, 320 L, 320B, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D2, 321C, 322, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 323D L, 323D2 L, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325...
6I6465 ADAPTER-TIP
322 LN, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 345B II, 345B L, 350
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.