7N3629 ADAPTER-FAN Caterpillar parts
834B, 836, 966F II, 988B
Rating:
Alternative (cross code) number:
CA7N3629
7N-3629
7N3629
CA7N3629
7N-3629
7N3629
Weight: 14 pounds 6 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 7N3629:
Number on catalog scheme:
10
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 1 g01361765
Attach a suitable lifting device to cylinder head (7) . The weight of cylinder head (7) is approximately 147 kg (325 lb). Position cylinder head (7) .
Illustration 2 g01361697
Note: Examine bolts (5) for wear or for damage. Refer to Reuse And Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines". Replace with new bolts (5) , if necessary.
Install bolts (5) and install bolts (6) .
Illustration 3 g02083414
Bolt tightening sequenceNote: Lubricate the bolts with clean engine oil prior to assembly.
Tighten bolt (1) through bolt (26) in a numerical sequence.Tighten the bolts to the following torque. ... 160 15 N m (118 11 lb ft)
Tighten bolt (1) through bolt (26) again in a numerical sequence.Tighten the bolts again to the following torque. ... 160 15 N m (118 11 lb ft)
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence.Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
Tighten bolt (1) through bolt (26) in a numerical sequence.Tighten the bolts to the following torque. ... 160 15 N m (118 11 lb ft)
Tighten bolt (1) through bolt (26) again in a numerical sequence.Tighten the bolts again to the following torque. ... 160 15 N m (118 11 lb ft)
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence.Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
Tighten bolt (27) through bolt (32) in a numerical sequence.Tighten the bolts to the following torque. ... 28 7 N m ( 21 5 lb ft)
Illustration 4 g01361667
Position bracket (2) and install bolts (3) .
Install bolts (4) .
Illustration 5 g01361659
Install tube assembly (1) .End By:
Install the unit injectors.
Install the rocker arm and shaft.
Install the inlet manifold.
Install the fuel filter base.
Install the fuel rail and the fuel manifold.
Install the fan drive mounting group.
Install the exhaust manifold.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Illustration 1 g01361765
Attach a suitable lifting device to cylinder head (7) . The weight of cylinder head (7) is approximately 147 kg (325 lb). Position cylinder head (7) .
Illustration 2 g01361697
Note: Examine bolts (5) for wear or for damage. Refer to Reuse And Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines". Replace with new bolts (5) , if necessary.
Install bolts (5) and install bolts (6) .
Illustration 3 g02083414
Bolt tightening sequenceNote: Lubricate the bolts with clean engine oil prior to assembly.
Tighten bolt (1) through bolt (26) in a numerical sequence.Tighten the bolts to the following torque. ... 160 15 N m (118 11 lb ft)
Tighten bolt (1) through bolt (26) again in a numerical sequence.Tighten the bolts again to the following torque. ... 160 15 N m (118 11 lb ft)
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence.Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
Loosen bolt (1) through bolt (26) until the washers are loose under the bolt heads.
Tighten bolt (1) through bolt (26) in a numerical sequence.Tighten the bolts to the following torque. ... 160 15 N m (118 11 lb ft)
Tighten bolt (1) through bolt (26) again in a numerical sequence.Tighten the bolts again to the following torque. ... 160 15 N m (118 11 lb ft)
Place a mark on bolt (1) through bolt (26) . Rotate bolt (1) through bolt (26) in a numerical sequence.Rotate the bolts in the clockwise direction. ... 90 degrees (1/4 turn)
Tighten bolt (27) through bolt (32) in a numerical sequence.Tighten the bolts to the following torque. ... 28 7 N m ( 21 5 lb ft)
Illustration 4 g01361667
Position bracket (2) and install bolts (3) .
Install bolts (4) .
Illustration 5 g01361659
Install tube assembly (1) .End By:
Install the unit injectors.
Install the rocker arm and shaft.
Install the inlet manifold.
Install the fuel filter base.
Install the fuel rail and the fuel manifold.
Install the fan drive mounting group.
Install the exhaust manifold.
Caterpillar parts catalog:
Parts adapter Caterpillar catalog:
1865386
ADAPTER-TIP
992C, 992D
992C, 992D
1865385
ADAPTER-TIP
992C, 992D
992C, 992D
1433116
ADAPTER-TIP
992C, 992D
992C, 992D
1433115
ADAPTER-TIP
992C, 992D
992C, 992D
1433114
ADAPTER-TIP
992C, 992D
992C, 992D
2238136
ADAPTER-TIP
988F, 988F II, 988G, 988H, 988K, 990 II, 990H, 990K, 992C, 992D
988F, 988F II, 988G, 988H, 988K, 990 II, 990H, 990K, 992C, 992D
9C2285
ADAPTER
988B, 988F, 988F II
988B, 988F, 988F II
1V4882
ADAPTER-PUMP
988B
988B
1V7443
ADAPTER-SCREW
834B, 988B, 988F, R1700G
834B, 988B, 988F, R1700G
6P1272
ADAPTER AS
24H, 834B, 836, 988B, 988F, 988F II, AD40, AE40, D10N, D10R, D9L, D9R
24H, 834B, 836, 988B, 988F, 988F II, AD40, AE40, D10N, D10R, D9L, D9R
24H, 834B, 836, 988B, AD40, AD45, AE40, AE40 II, D10N, D10R, D8L, D9L, D9R
24H, 834B, 836, 988B, AD40, AD45, AE40, AE40 II, D10N, D10R, D8L, D9L