8I0732 ADJUSTER GP-HEIGHT Caterpillar parts
10 FT, 10-20B, 8 FT, 8-16B, AP-800C, BG-225B, BG-245C
Rating:
Alternative (cross code) number:
CA8I0732
8I-0732
8I0732
CA8I0732
8I-0732
8I0732
Weight: 9 pounds 4 kg.
ASPHALT PAVER, ASPHALT SCREED,
Compatible equipment models: 8I0732:
Number on catalog scheme:
For full view, you need register
Information:
TYPE="TABLE" @@@-->
Illustration 1 g00564972
Schematic For Temperature Sender (Intake Manifold Air)Note: Ensure that the diagnostic code (CID FMI) is on hold. Ensure that the "SERV CODE" indicator is ON. Use the electrical system schematic for the engine that is being serviced to find the connector contact on the main display module. The contact should correspond to the CID that is shown in the Display Area.This diagnostic code is recorded when the Main Display Module reads a low signal from the sender. As a result of this diagnostic code, the corresponding Gauge Needle moves to the warning region. The following examples are possible causes of a CID 0172 FMI 04.
The temperature sender (intake manifold air) has a problem.
The signal circuit of the temperature sender (intake manifold air) is shorted to ground in the engine harness.
The Main Display Module has a problem.Note: The main display module is unable to determine the following conditions: an open sender, an open signal from the sender harness and very high resistance on the signal from the sender harness. This condition causes the corresponding Gauge Needle to stay at the left side of the scale.
Measure The Resistance Of The Sender.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the temperature sender (intake manifold air).
Measure the resistance between the two connector contacts of the sender. The correct approximate resistances are listed in the table below.
Table 1
Resistance Table
Temperature Resistance
25.0 2°C (77.0 3.6°F) 1000 Ohms
100 2°C (212 3.6°F) 103.7 Ohms
Check The Display Area And The Harness.
Turn the "ECS" switch to the OFF/RESET position.
Check for loose terminal contacts on the temperature sender (intake manifold air). Check for loose connections or corroded connections to the temperature sender (intake manifold air).
Replace corroded contacts and tighten loose connections.
Turn the "ECS" switch to the COOLDOWN/STOP position. The "SERV CODE" indicator should be ON forCID 172 FMI 04.
Disconnect the engine harness from the temperature sender (intake manifold air).
Observe the "SERV CODE" indicator.Expected Result: The "SERV CODE" indicator should turn OFF.Results:
OK: The "SERV CODE" indicator turns OFF. The temperature sender (intake manifold air) has a problem. Replace the temperature sender (intake manifold air).
Not OK: The "SERV CODE" indicator stays ON.
Illustration 1 g00564972
Schematic For Temperature Sender (Intake Manifold Air)Note: Ensure that the diagnostic code (CID FMI) is on hold. Ensure that the "SERV CODE" indicator is ON. Use the electrical system schematic for the engine that is being serviced to find the connector contact on the main display module. The contact should correspond to the CID that is shown in the Display Area.This diagnostic code is recorded when the Main Display Module reads a low signal from the sender. As a result of this diagnostic code, the corresponding Gauge Needle moves to the warning region. The following examples are possible causes of a CID 0172 FMI 04.
The temperature sender (intake manifold air) has a problem.
The signal circuit of the temperature sender (intake manifold air) is shorted to ground in the engine harness.
The Main Display Module has a problem.Note: The main display module is unable to determine the following conditions: an open sender, an open signal from the sender harness and very high resistance on the signal from the sender harness. This condition causes the corresponding Gauge Needle to stay at the left side of the scale.
Measure The Resistance Of The Sender.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the temperature sender (intake manifold air).
Measure the resistance between the two connector contacts of the sender. The correct approximate resistances are listed in the table below.
Table 1
Resistance Table
Temperature Resistance
25.0 2°C (77.0 3.6°F) 1000 Ohms
100 2°C (212 3.6°F) 103.7 Ohms
Check The Display Area And The Harness.
Turn the "ECS" switch to the OFF/RESET position.
Check for loose terminal contacts on the temperature sender (intake manifold air). Check for loose connections or corroded connections to the temperature sender (intake manifold air).
Replace corroded contacts and tighten loose connections.
Turn the "ECS" switch to the COOLDOWN/STOP position. The "SERV CODE" indicator should be ON forCID 172 FMI 04.
Disconnect the engine harness from the temperature sender (intake manifold air).
Observe the "SERV CODE" indicator.Expected Result: The "SERV CODE" indicator should turn OFF.Results:
OK: The "SERV CODE" indicator turns OFF. The temperature sender (intake manifold air) has a problem. Replace the temperature sender (intake manifold air).
Not OK: The "SERV CODE" indicator stays ON.
Caterpillar SIS machinery equipment:
Caterpillar SIS
8-16B EXTEND-A-MAT Screed 3GL00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
10-20B, 10-20WB EXTEND-A-MAT Screed 3HL00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
10-20B 10-20WB EXTEND-A-MAT Screed 3EL00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
3054 Engine 6YK00001-UP (MACHINE) »
8I-0732
ADJUSTER GP-HEIGHT
CATERPILLAR AP-800C BARBER-GREENE BG-230 Asphalt Pavers 1PM00001-UP (MACHINE) POWERED BY 3054 Engine »
8I-0732
ADJUSTER GP-HEIGHT
8-16B EXTEND-A-MAT Screed 2JN00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
10-20B EXTEND-A-MAT Screed 2KN00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
CATERPILLAR AP-1050B BARBER-GREENE BG-245C Asphalt Pavers 4XN00001-UP (MACHINE) POWERED BY 3116 Engine »
8I-0732
ADJUSTER GP-HEIGHT
10-20B EXTEND-A-MAT Screed 2LN00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
8-16B Screed 7MR00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
10-20B EXTEND-A-MAT Screed AGT00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
8-16B EXTEND-A-MAT Screed BLK00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
8-16B SCREED BWL00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
10-20B Screed BWN00001-UP »
8I-0732
ADJUSTER GP-HEIGHT
Caterpillar parts catalog:
Parts adjuster Caterpillar catalog:
7Y3477
ADJUSTER GP-BUCKET
330C, 345C, 345C L, 345D L, 345D L VG, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 390F L, 5080
330C, 345C, 345C L, 345D L, 345D L VG, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 390F L, 5080
0875960
ADJUSTER GP-BUCKET
115, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 345B, 345B II, 345B L, 345C, 350, H140CS, H140DS
115, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 345B, 345B II, 345B L, 345C, 350, H140CS, H140DS
7Y3475
ADJUSTER GP-BUCKET
315, 317, 320, 320 L, 320B, 320B FM LL, 320C, 320N, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330 FM L, 330 L, 330B L, 365B II, 365C, 365C L
315, 317, 320, 320 L, 320B, 320B FM LL, 320C, 320N, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330 FM L, 330 L, 330B L, 365B II, 365C, 365C L
8V1177
ADJUSTER GP-SEAT
916, 926, 926A, 936, CS-643, D5H, G936, IT18, IT28
916, 926, 926A, 936, CS-643, D5H, G936, IT18, IT28
115, 312, 315, 315C, 317, 318B, 318C, 319C, 319D, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C L, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN...
2506418
ADJUSTER GP-BUCKET
320D, 320D L, 320D LRR, 320D RR, 320D2, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 3...
320D, 320D L, 320D LRR, 320D RR, 320D2, 323D L, 323D LN, 323D SA, 323D2 L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 3...
3478750
ADJUSTER GP-SEAT
725C, 730C, 735B, 740B, 950H, 962H, 966H, 972H, 980H, 986H
725C, 730C, 735B, 740B, 950H, 962H, 966H, 972H, 980H, 986H
1123471
ADJUSTER GP-HEIGHT
10-20B, 8-16B
10-20B, 8-16B
4V8599
ADJUSTER GP-SEAT
814B, 824C, 834B, 920, 930, 943, 950, 950B, 950B/950E, 953, 955L, 963, 966C, 966D, 973, 977L, 980C, D7G, D7H
814B, 824C, 834B, 920, 930, 943, 950, 950B, 950B/950E, 953, 955L, 963, 966C, 966D, 973, 977L, 980C, D7G, D7H
1731029
ADJUSTER GP-SEAT
725, 730, 735, 740, 785B, 789B, 793C, D250E II, D300E II, D350E II, D400E II
725, 730, 735, 740, 785B, 789B, 793C, D250E II, D300E II, D350E II, D400E II
1066757
ADJUSTER GP-BUCKET
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L, 323D L, 63, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L, 323D L, 63, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318C
1259854
ADJUSTER GP-SEAT
120H, 120K, 120K 2, 12H, 12K, 135H, 140H, 140K, 140K 2, 160H, 160K
120H, 120K, 120K 2, 12H, 12K, 135H, 140H, 140K, 140K 2, 160H, 160K