AVSPARE.COM
parts catalog

ADJUSTER GP-SEAT 8Y3771 - Caterpillar


8Y3771 ADJUSTER GP-SEAT Caterpillar parts 120G, 12G, 130G, 140G, 160G, 930R, RM-350B, SM-350
Rating:
37
Alternative (cross code) number:
CA8Y3771
8Y-3771
8Y3771
Caterpillar 8Y3771 ADJUSTER GP-SEAT
Weight: 31 pounds 14 kg.

Buy ADJUSTER GP-SEAT 8Y3771 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER, WHEEL LOADER,

Compatible equipment models: 8Y3771:

MOTOR GRADER  120G   12G   130G   140G   160G  
RECLAIMER MIXER  RM-350B  
STABILIZER MIXER  SM-350  
WHEEL LOADER  930R   Caterpillar
Number on catalog scheme: 1
  For full view, you need register

Information:


During operation, the linkage of the electrohydraulic actuators can form pinch points which can cause personal injury. Shut down the engine before you service the electrohydraulic actuators.
Illustration 1 g00833592
(1) Receptacle for the wiring harness (2) Guards
Disconnect the wiring harness from receptacle (1). Inspect the connectors for damage and corrosion. Make repairs, if necessary.
Remove guards (2) .
Disconnect the supply line (not shown) and the return line (not shown) for the hydraulic oil.
Illustration 2 g00833594
(3) Rod end (4) Clevis (5) Boot (6) Nut
Disconnect rod end (3) from clevis (4) .
Remove clevis (4) and rubber boot (5). Inspect the boot for damage. If the boot is damaged, obtain a new boot for assembly.Note: Handle the actuator carefully. Use care not to damage the actuator shaft. Damage to the shaft can result in premature failure of the O-ring seal. This failure will cause hydraulic fluid to leak.
Remove nut (6) in order to remove the actuator from the bracket.Note: Do not allow debris to enter the actuator. Seal the openings with clean covers immediately after the solenoid and/or the piston assembly is removed.
Illustration 3 g00833595
(7) Housing (8) Piston assembly (9) O-ring seal (10) Bolt (11) Solenoid (12) O-ring sealNote: The spring in the housing will be loose after the piston assembly is removed.
Place housing (7) in a vise. Remove piston assembly (8). Remove O-ring seal (9) from the joint between the piston assembly and the housing.Note: O-ring seal (9) is included with the piston assembly.
Install a new O-ring seal (9) and piston assembly (8). Make sure that the spring in the housing is properly aligned in the bore of the piston. Tighten the piston assembly according to the engineSpecifications.
Remove bolts (10) in order to remove solenoid (11). Remove O-ring seal (12) from the joint between the solenoid and the housing.
Install a new O-ring seal (12) and solenoid (11). Install bolts (10). Tighten the bolts according to the engine Specifications.
Install the actuator in the bracket with nut (6) .
Install boot (5). Ensure that the outer end of the boot folds inward when the actuator shaft moves from the fully open position to the fully closed position.
Install clevis (4). Connect rod end (3) to the clevis.
Install guards (2) .
Connect the supply line and the return line for the hydraulic oil.
Connect the wiring harness to receptacle (1) .

Caterpillar parts catalog:

Caterpillar parts catalog
RM-350, SM-350 Reclaimer, Stabilizer Mixer 1RM00001-00059 (MACHINE) POWERED BY 3406C Engine
RM-350 SM-350 Reclaimer, Stabilizer Mixer 1RM00060-UP (MACHINE) POWERED BY 3406C Engine
RM-350B Reclaimer Mixer 7FS00001-UP (MACHINE) POWERED BY 3406C Engine
140G Motor Grader 72V10334-UP (MACHINE) POWERED BY 3306 Engine
120G Motor Grader 87V08360-UP (MACHINE) POWERED BY 3304 Engine
12G Motor Grader 61M12027-UP (MACHINE) POWERED BY 3306 Engine
130G Motor Grader 74V02321-UP (MACHINE) POWERED BY 3304 Engine
120G Motor Grader 4HD00001-UP (MACHINE) POWERED BY 3304 Engine
140G Motor Grader 5MD00001-UP (MACHINE) POWERED BY 3306 Engine
160G Motor Grader 4JD00141-UP (MACHINE) POWERED BY 3306 Engine
12G Motor Grader 3PL00001-UP (MACHINE) POWERED BY 3306 Engine
930T SERIES II WHEEL LOADER 17B02011-UP (MACHINE) POWERED BY 3304 ENGINE


Parts adjuster Caterpillar catalog:

1220160 ADJUSTER GP-STRIKE-OFF
10 FT, 10B, AP-800C, BG-225B, BG-245C
2492969 ADJUSTER GP-SEAT
769D, 770, 771D, 772, 773D, 773E, 773F, 775D, 775E, 775F, 776D, 777D, 777F, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797B
1654722 ADJUSTER GP-POWER
AP-800C, AS2251, AS2301, AS2302, BG-225B
2457889 ADJUSTER GP-SEAT
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 307D, 311D LRR, 311F LRR, 312D, 312D L, 315D L, 319D, 319D L, 319D LN, 320C FM, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D ...
3203021 ADJUSTER GP-HEIGHT
AP-600D, AP-655D, AP555E, AS4251C
2165734 ADJUSTER GP-BUCKET
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 365B, 365B II, 365C, 365C L, 374D L, 374F L
7Y3476 ADJUSTER GP-BUCKET
115, 315, 317, 321C, 322, 322 LN, 322B L, 322B LN, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, H140CS, H140DS
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.