1647560 AIR COMPRESSOR GP Caterpillar parts
3304, 3306, 3306B, 3306C
Rating:
Alternative (cross code) number:
CA1647560
164-7560
1647560
CA1647560
164-7560
1647560
GEN SET ENGINE, TRUCK ENGINE,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$616.35
04 Dec 2018
109287 | Caterpillar 3306 TF750 Brake Air Compressor, Remanufactured
Air Compressor for Caterpillar 3306 Applications - Reman. TF750 Notes: R.S., Spline Shaft, 22 tooth, Flange Mount, Air Inlet: Left, Air Outlet: Top or Left X-Ref Numbers: 109287X, R109287, 065491, 0R3405, 1091318, 109285, 109286, 109287, 109336, 1442907, 1105766, 1647560, 1647561, 1647562, 5003648, 5003649, 5005415, 5005416, 5005417, 5005466, 65491, 745X109287, E-BN109287X, R065491, R109336, R109285, R109286, R5005415, R5005416, R5005417, R5005466, R5003648, R5003649, R955109287X || Caterpillar || Home>Air Compressor Drive>Caterpillar
Air Compressor for Caterpillar 3306 Applications - Reman. TF750 Notes: R.S., Spline Shaft, 22 tooth, Flange Mount, Air Inlet: Left, Air Outlet: Top or Left X-Ref Numbers: 109287X, R109287, 065491, 0R3405, 1091318, 109285, 109286, 109287, 109336, 1442907, 1105766, 1647560, 1647561, 1647562, 5003648, 5003649, 5005415, 5005416, 5005417, 5005466, 65491, 745X109287, E-BN109287X, R065491, R109336, R109285, R109286, R5005415, R5005416, R5005417, R5005466, R5003648, R5003649, R955109287X || Caterpillar || Home>Air Compressor Drive>Caterpillar
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 1647560:
Information:
Remove & Install Connecting Rod Bearings
Start By:a. remove oil pump 1. Check each connecting rod cap for its location on the crankshaft. Each cap must have a number (1) which is the same as the number on the connecting rod. Do not mix bearings.2. Use Tool (A) to turn the crankshaft until two of the pistons are at bottom center.3. Remove connecting rod caps (2). Remove the lower bearing from the connecting rod caps.4. Push the connecting rods away from the crankshaft and remove the upper bearings from the connecting rods.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
The following steps are for the installation of the connecting rod bearings. If the bearing clearances are to be checked with Plastigage, DO NOT put oil on the parts until the bearing clearance has been checked.5. Install the upper bearings in connecting rods. Put clean engine oil on the bearings and on the crankshaft journals. Slowly pull the connecting rods on the crankshaft.6. Put clean oil on the lower bearings. Install the lower bearings in the connecting rod caps. Be sure tab (3) on the back of the bearings fits in the groove of the caps and connecting rods. When connecting rod caps are installed, make sure the number on the side of the cap is next to, and respective with the number on the side of the connecting rod. 7. Make a check of the bearing clearance with Plastigage (4). Put clean engine oil on bolt threads (5). Put caps (2) in position on the connecting rods and install the nuts. Tighten the nuts with the procedure that follows:a. Tighten each nut (6) to a torque of 80 9 N m (60 6 lb ft).b. Put a mark across the nuts and bolts. Tighten the nuts 120° more.
Do not use an impact wrench to tighten the nuts the additional 120°.
8. Remove the cap and measure the Plastigage. The rod bearing clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066 in). The maximum clearance for used bearings is 0.25 mm (.010 in).9. Put bearing cap (2) in position and tighten the bolts as in Step 7.10. Do steps 1 through 9 for the other connecting rod bearings.End By:a. install oil pump
Start By:a. remove oil pump 1. Check each connecting rod cap for its location on the crankshaft. Each cap must have a number (1) which is the same as the number on the connecting rod. Do not mix bearings.2. Use Tool (A) to turn the crankshaft until two of the pistons are at bottom center.3. Remove connecting rod caps (2). Remove the lower bearing from the connecting rod caps.4. Push the connecting rods away from the crankshaft and remove the upper bearings from the connecting rods.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
The following steps are for the installation of the connecting rod bearings. If the bearing clearances are to be checked with Plastigage, DO NOT put oil on the parts until the bearing clearance has been checked.5. Install the upper bearings in connecting rods. Put clean engine oil on the bearings and on the crankshaft journals. Slowly pull the connecting rods on the crankshaft.6. Put clean oil on the lower bearings. Install the lower bearings in the connecting rod caps. Be sure tab (3) on the back of the bearings fits in the groove of the caps and connecting rods. When connecting rod caps are installed, make sure the number on the side of the cap is next to, and respective with the number on the side of the connecting rod. 7. Make a check of the bearing clearance with Plastigage (4). Put clean engine oil on bolt threads (5). Put caps (2) in position on the connecting rods and install the nuts. Tighten the nuts with the procedure that follows:a. Tighten each nut (6) to a torque of 80 9 N m (60 6 lb ft).b. Put a mark across the nuts and bolts. Tighten the nuts 120° more.
Do not use an impact wrench to tighten the nuts the additional 120°.
8. Remove the cap and measure the Plastigage. The rod bearing clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066 in). The maximum clearance for used bearings is 0.25 mm (.010 in).9. Put bearing cap (2) in position and tighten the bolts as in Step 7.10. Do steps 1 through 9 for the other connecting rod bearings.End By:a. install oil pump
Caterpillar SIS machinery equipment:
Caterpillar SIS
3304 Industrial Engine 10E00300-UP »
164-7560
AIR COMPRESSOR GP
3306 Generator Set 85Z00001-03763 »
164-7560
AIR COMPRESSOR GP
3306 Industrial Engine 66D49919-UP »
164-7560
AIR COMPRESSOR GP
3306 Industrial Engine 64Z05381-UP »
164-7560
AIR COMPRESSOR GP
3306 Generator Set 85Z03764-UP »
164-7560
AIR COMPRESSOR GP
3304 Industrial Engine 02B17737-UP »
164-7560
AIR COMPRESSOR GP
3304B Generator Set 83Z03096-UP »
164-7560
AIR COMPRESSOR GP
3306C Truck Engine 9TL00001-UP »
164-7560
AIR COMPRESSOR GP
3304 Industrial Engine 04B26769-UP »
164-7560
AIR COMPRESSOR GP
3306B Generator Set 9NR00001-UP »
164-7560
AIR COMPRESSOR GP
3306B Industrial Engine 5GZ00001-UP »
164-7560
AIR COMPRESSOR GP
3306 Industrial Engine 23C02002-UP »
164-7560
AIR COMPRESSOR GP
Caterpillar parts catalog:
Parts air Caterpillar catalog:
3304, 3306, 3306B, 3306C
16G, 3306, 3306B, 621E, 621F, 623E, 623F, 627E, 627F, 824C, 825C, 826C, 980F, 980F II, D25D
3304, 3306, 3306B, 3306C
12H, 12H ES, 12H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 1673C, 3304, 3306, 3306B, 3306C, 611, 615C, 966F, 966F II, G3306
14H NA, 3306, 3306C, 611, 615C
16G, 245, 3306, 3306B, 583K, 621B, 621E, 621R, 623B, 623E, 627B, 627E, 824C, 826C, 980B, 980C, 980F, D250B, D25C, D25D, D300B, D300D, D30C, D350C, D35C, D35HP, D400, D40D, D8H, D8K, R2900
1673, 3306, D8H
3304, 3306, 3306B, 627, 627B, 637D
1673, 1673C, 3304, 3306, 3306B, 3306C
12E, 215, 3304, 3306, 518, 561B, 920, D4D, D4E, RT50
140G, 14G, 160G, 3304, 572G, D7G
3820433
AIR CONDITIONER & MOUNTING GP
307E, 308E, 308E2 CR
307E, 308E, 308E2 CR
1502223
AIR CONDITIONER ARRANGEMENT
311B, 312B
311B, 312B
7L7414
AIR FILTER INDICATOR GROUP
3304, 3306, D330A, D330B
3304, 3306, D330A, D330B
2161093
AIR CONDITIONER GP
TH210, TH215
TH210, TH215
2262774
AIR CLEANER GP
3512C, 3516B, C27, C32, PM3516
3512C, 3516B, C27, C32, PM3516
3866143
AIR CONDITIONER & MOUNTING GP
308E CR, 308E SR
308E CR, 308E SR
3962185
AIR CLEANER GP
318D2 L
318D2 L
4L3622
AIR CLEANER GROUP
D353C
D353C
525C, 535C, 545C, 815B