AIR COMPRESSOR GP 1752172 - Caterpillar

1752172 AIR COMPRESSOR GP Caterpillar parts C-10, C-12

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1752172
175-2172
1752172

Buy AIR COMPRESSOR GP 1752172 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK ENGINE,

Compatible equipment models: 1752172:

TRUCK ENGINE C-10 C-12 Caterpillar

Number on catalog scheme:

Caterpillar 1752172 Parts scheme AIR COMPRESSOR GP

For full view, you need register

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5p-7306 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and Assembly, "Balancer - Remove" for the correct procedure.
If the engine is not equipped with a balancer, remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to the piston cooling jet.
Illustration 1 g02011713
Remove bolt (2) and piston cooling jet (1) from the cylinder block. Remove O-ring seal (3).
Repeat Step 1 through Step 2 for the remaining piston cooling jets. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 5p-7306 Housing 1
5P-7305 Engine Turning Tool 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g02011713
Clean the piston cooling jets and inspect the piston cooling jets for damage. Ensure that the valve is free to move within each piston cooling jet. Replace any damaged piston cooling jets. The procedure for checking the alignment of the piston cooling jets is described in Specifications, "Piston Cooling Jet Alignment".
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to access the mounting flange for the piston cooling jet.
Install a new O-ring seal (3) onto piston cooling jet (2).
Position piston cooling jet (2) in the cylinder block. Install bolt (1). Tighten the bolt to a torque of 9 N m (80 lb in).
Repeat Step 2 through Step 4 for the remaining piston cooling jets. End By:
If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and Assembly, "Balancer - Install" for the correct procedure.
If the engine is not equipped with a balancer, install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.

Caterpillar SIS machinery equipment:

Caterpillar SIS

C-10 Truck Engine 3CS00001-UP » 175-2172 AIR COMPRESSOR GP

C-12 Truck Engine 2KS00001-UP » 175-2172 AIR COMPRESSOR GP

C-12 Truck Engine CPD00001-UP » 175-2172 AIR COMPRESSOR GP

Parts air Caterpillar catalog:

1316679 AIR COMPRESSOR GP
140H, 143H, 14H, 160H, 163H, 16H, 3176C, 3196, 3406E, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 657B, 657E, 657G, 824C, C-10, C-12, C-15, C-16, C-18