AIR COMPRESSOR GP 4238726 - Caterpillar

4238726 AIR COMPRESSOR GP Caterpillar parts CW-34

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4238726
423-8726
4238726

Weight: 58 pounds 26 kg.

Buy AIR COMPRESSOR GP 4238726 Caterpillar genuine, new aftermarket tractor parts with delivery
PNEUMATIC COMPACTOR,

This part in 3 request: Show. This information for suppliers only!

#1024032 4238726

2022-12-14

#970452 4238726

2022-09-15

#970452 4238726

2022-09-15

Compatible equipment models: 4238726:

PNEUMATIC COMPACTOR CW-34 Caterpillar

Number on catalog scheme: 1

Caterpillar 4238726 Parts scheme AIR COMPRESSOR GP

For full view, you need register

Information:

Illustration 1 g01122872Note: Be sure that the lubrication holes are aligned during the installation of the bearings.
Use Tooling (J) to install the bearings in the lift cylinder pin bores. Install the bearings to a depth of 10 1 mm (0.394 0.04 inch) below the surface of the lift arm assembly.
Illustration 2 g01122874
Use Tooling (K) to install the lip seals on each side of the lift cylinder pin bores. Install the lip of the seals away from the bearings.
Illustration 3 g01122880Note: Be sure that the lubrication holes are aligned during the installation of the bearings.
Use Tooling (L) to install the bearings in the pivot pin bores. Install the bearings to a depth of 10 1 mm (0.394 0.04 inch) below the surface of the lift arm assembly.
Illustration 4 g01122883
Use Tooling (K) to install the lip seals on each side of the pivot pin bores. Install the lip of the seals away from the bearings.
Illustration 5 g00532287Note: Be sure that the lubrication holes are aligned during the installation of the bearings.
Use Tooling (M) to install the bearings in the bucket pin bores. Install the bearings to a depth of 0.4 +0/- 0.4 mm to 0.016 +0/-.016 inch below the surface of the lift arm assembly.
Illustration 6 g01122885
Use Tooling (K) to install the lip seals on each side of the bucket pin bores. Install the lip of the seals away from the bearings.
Lubricate the pin bores in the lift arm assembly and in the front loader frame with Tooling (N).
Illustration 7 g01112076
Fasten a suitable lifting device and Tooling (H) to lift arm assembly (7). Put the lift arm assembly in alignment with the pin bores of the front loader frame. The weight of the lift arm assembly is approximately 2041 kg (4500 lb).
Illustration 8 g01112067Note: Do not damage the lip seals while you are installing the pin assemblies.
Fasten a suitable lifting device to pin assembly (5). The weight of each pin assembly (5) is approximately 32 kg (70 lb). Install the pin assemblies (5).
Install nut (6), the washer and the spacer to each pin assembly (5). Tighten the nuts to a torque of 250 40 N m (185 30 lb ft).
Illustration 9 g00531996
Put Tooling (B) in position under the lift arm assembly. Put the weight of the lift arm assembly on Tooling (B).
Illustration 10 g00532296
Illustration 11 g01112143
Use a suitable lifting device in order to put the rod end of the lift cylinders in alignment with the pin bores of the lift arm assembly. Note: Do not damage the lip seals while you are installing the pin assemblies.
Use a suitable lifting device and install pin assemblies (4). The weight of each pin assembly is approximately 20 kg (45 lb). .
Install bolt (2), the washer and the spacer in the pin assemblies. Tighten the bolts to a torque of 460 60 N m (339 44 lb ft).
Start the machine. Raise the lift arms. Remove suitable blocks (3) from the lift arm assembly and the cylinder rods. Remove Tooling (B) from the machine. Lower the lift arm