AIR CONDITIONER & MOUNTING GP 5087773 - Caterpillar

Torque Converter
TORQUE CONVERTER HYDRAULIC CONTROLS 1. Oil filter.2. Transmission hydraulic controls.3. Torque converter.4. Oil pump.5. Relief valve for converter outlet.6. Body of relief valve for converter outlet.7. Screen.8. Oil reservoir.9. Oil cooler.A. Pressure tap for oil pump (on filter).B. Pressure tap for relief valve.C. Pressure tap for converter inlet (P3).D. Pressure tap for converter outlet.E. Pressure tap for lubrication.Location Of The Pressure Taps
5P6586 TRANSMISSION TEST COVER INSTALLED (Typical Example)
C. Converter inlet (P3).
D. Converter outlet.
Activate the brakes and use blocks to prevent machine movement during tests and adjustments to the converter hydraulic system. Install the anti-pivot link. Let only approved personnel on the machine. Keep other personnel off the machine and in view of the operator.
RELIEF VALVE FOR TORQUE CONVERTER OUTLET
5. Relief valve for converter outlet. 6. Body of relief valve for converter outlet. 10. Spacers. Power Shift Transmission
TRANSMISSION HYDRAULIC CONTROLS (First Speed Forward, Engine Running) 1. Oil filter.2. Torque converter.3. Body of relief valve for converter outlet.4. Relief valve for converter outlet.5. Oil cooler.6. No. 5 clutch.7. No. 4 clutch.8. No. 6 clutch.9. Oil pump.10. Speed selection spool.11. Load piston.12. Spring.13. Modulation relief valve.14. Pressure differential valve.15. Screen.16. Inlet pressure valve for torque converter.17. Direction selection spool.18. No. 1 clutch.19. No. 3 clutch.20. No. 2 clutch.21. Reservoir.22. Flow control orifice.A. Pressure tap for pump (on filter).B. Pressure tap for converter outlet.C. Pressure tap for transmission lubrication.D. Pressure tap for converter inlet (P3).E. Pressure tap for speed clutch (P1).F. Pressure tap for direction clutch (P2).Location Of The Pressure Taps
A. Oil pump (on filter).
C. Transmission Lubrication.
E. Speed clutch (P1). F. Direction clutch (P2). G. Plug for load piston (LP).
When tests and adjustments are made to the transmission, remove both front and rear axle shafts, install the anti-pivot link, and lower the blade to the ground. Let only approved personnel on the machine. Keep other personnel off the machine and in view of the operator.
All tests and adjustments must be made with the oil in the hydraulic control system at normal temperature of operation. Be sure the linkage adjustments are correct before tests are made.
TRANSMISSION SELECTOR AND PRESSURE CONTROL VALVE
10. Speed selection spool. 11. Load piston. 13. Modulation relief valve. 14. Pressure differential valve. 16. Inlet pressure valve for torque converter. 17. Direction selection spool. 23. Spacers.
TRANSMISSION SELECTOR AND PRESSURE CONTROL VALVE
24. Setscrews (two). 25, 26. Holes (No. 10-24 Threads). X. Surface of valve body. Setscrews (24) must be installed in holes (25) and (26). Setscrews (24) permit correct operation of load piston (11). Setscrews must be assembled below surface (X). Transmission Control Linkage Adjustments
Direction Linkage
1. Put direction selection spool (1) in the NEUTRAL position.2. Make an adjustment to the length of rod (2) so that distance (A) from the center line of pin (4) to the face of cam (5) is 3.18 in. (80.7 mm).3. Install the cable assembly in neutralizer housing (6) so that distance (C) is .47 in. (12.0 mm).
DIRECTION CONTROL LINKAGE (At Transmission)
1. Direction selection spool. 2. Rod. 3. Cable assembly. 4. Pin. 5. Cam. 6.