1555518 ALTERNATOR GP-CHARGING Caterpillar parts
554, 574, 574B
Rating:
Alternative (cross code) number:
CA1555518
155-5518
1555518
CA1555518
155-5518
1555518
Weight: 18 pounds 8 kg.
FORWARDER,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$53.22
11 Jul 2019
Van Wezel Gmbh: Van Wezel Gmbh
Van Wezel 1555518 Radiator Grille
Styling: with trim strip || Surface: Chromed || Quality Product
Styling: with trim strip || Surface: Chromed || Quality Product
Number on catalog scheme:
1
For full view, you need register
Caterpillar parts catalog:
Information:
Remove Brake Relay Valves
There are three relay valves on a common bracket on the inside of the truck frame. The relay valves are: (A) front brakes relay valve, (B) retarder relay valve, (C) service brake relay valve.
To prevent possible personal injury remove air from the system before any hoses are disconnected.
1. Lift the truck body and put FT1437 Body Support in position. See INSTALL AND REMOVE BODY SUPPORT on Page 8. Put identification on all electrical wires and hoses connected to the relay valves for correct installation.2. Disconnect electrical wires from switch (5).3. Disconnect three hoses (2), (4) and (6) from the relay valves.4. Remove three bolts (1) that fasten plate (3) to the frame. 5. Disconnect electrical wires from switch (7).6. Disconnect five hoses (8), (9), (10), (11) and (12) from the relay valves. 7. Remove six nuts (13), bolts that fasten the relay valves to the plate. 8. Make a separation of three relay valves (14).Install Brake Relay Valves
1. Make a connection of three relay valves (1). Install the valves on plate (2) with six bolts, nuts, washers and lockwashers. 2. Connect electrical wires to switch (3).3. Connect five hoses (4) to the relay valves. 4. Put the relay valves and plate (2) in position in the frame. Install the three bolts, nuts and lockwashers that fasten the plate to the frame. 5. Connect electrical wires to switch (7).6. Connect three hoses (5), (6) and (8) to the relay valves.Disassemble Brake Relay Valve
start by:a) remove brake relay valve 1. Remove four bolts (1) and remove the cover from housing (2). 2. Remove piston (3) and O-ring seal from cover (4). 3. Remove O-ring seal (5) from housing (2). 4. Remove four screws (6) and cover (7) from the housing. 5. Remove valve (8), spring (9), seal holder (7) and washer from the housing.Assemble Brake Relay Valve
1. Inspect the condition of all O-ring seals and make replacements as needed. 2. Install seals on seal holder (2) and valve (1). Install the valve, spring (4), seal holder and washer (5) in housing (3). 3. Install cover (6) on the housing with four screws. 4. Install O-ring seal (7) on housing (3). 5. Install seal (8) on piston (9), and install the piston in cover (10). 6. Install housing assembly (3) on cover assembly (10) with four bolts.
There are three relay valves on a common bracket on the inside of the truck frame. The relay valves are: (A) front brakes relay valve, (B) retarder relay valve, (C) service brake relay valve.
To prevent possible personal injury remove air from the system before any hoses are disconnected.
1. Lift the truck body and put FT1437 Body Support in position. See INSTALL AND REMOVE BODY SUPPORT on Page 8. Put identification on all electrical wires and hoses connected to the relay valves for correct installation.2. Disconnect electrical wires from switch (5).3. Disconnect three hoses (2), (4) and (6) from the relay valves.4. Remove three bolts (1) that fasten plate (3) to the frame. 5. Disconnect electrical wires from switch (7).6. Disconnect five hoses (8), (9), (10), (11) and (12) from the relay valves. 7. Remove six nuts (13), bolts that fasten the relay valves to the plate. 8. Make a separation of three relay valves (14).Install Brake Relay Valves
1. Make a connection of three relay valves (1). Install the valves on plate (2) with six bolts, nuts, washers and lockwashers. 2. Connect electrical wires to switch (3).3. Connect five hoses (4) to the relay valves. 4. Put the relay valves and plate (2) in position in the frame. Install the three bolts, nuts and lockwashers that fasten the plate to the frame. 5. Connect electrical wires to switch (7).6. Connect three hoses (5), (6) and (8) to the relay valves.Disassemble Brake Relay Valve
start by:a) remove brake relay valve 1. Remove four bolts (1) and remove the cover from housing (2). 2. Remove piston (3) and O-ring seal from cover (4). 3. Remove O-ring seal (5) from housing (2). 4. Remove four screws (6) and cover (7) from the housing. 5. Remove valve (8), spring (9), seal holder (7) and washer from the housing.Assemble Brake Relay Valve
1. Inspect the condition of all O-ring seals and make replacements as needed. 2. Install seals on seal holder (2) and valve (1). Install the valve, spring (4), seal holder and washer (5) in housing (3). 3. Install cover (6) on the housing with four screws. 4. Install O-ring seal (7) on housing (3). 5. Install seal (8) on piston (9), and install the piston in cover (10). 6. Install housing assembly (3) on cover assembly (10) with four bolts.
Parts alternator Caterpillar catalog:
1392617
ALTERNATOR GP-CHARGING
3054, 3054B, 312B L, 312C, 315B L, 554, BG-225C, M312, M315
3054, 3054B, 312B L, 312C, 315B L, 554, BG-225C, M312, M315
3054, 3054B, 3056, 307, 312, 312B L, 312C, 315, 315B L, 317, 554, BG-225C, M312, M315, M316C, M318C, M318C MH, M322C
0042987
ALTERNATOR
WE-601B
WE-601B
06006319
ALTERNATOR ADAPTER KIT
TSF-54, TSM-54
TSF-54, TSM-54
AP-1200
1G7266
ALTERNATOR GP
AP-800
AP-800
0827022
ALTERNATOR
CB-521, CB-525B, PS-300
CB-521, CB-525B, PS-300
7R4180
ALTERNATOR
AP-800, CP-433B, CS-323
AP-800, CP-433B, CS-323
E200B
E110B, E120, E120B, E140, E200B
1714257
ALTERNATOR GP
D7R II
D7R II
