2301584 ALTERNATOR GP-CHARGING Caterpillar parts
834G, 836G, 988G
Rating:
Alternative (cross code) number:
CA2301584
230-1584
2301584
CA2301584
230-1584
2301584
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 2301584:
Number on catalog scheme:
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar SIS
Custom Product Support Literature for the 988G Wheel Loader 2TW00001-UP (MACHINE) »
230-1584
ALTERNATOR GP-CHARGING
2Q-8490 Modification Ar-Scoop Custom Product Support Literature for the 834G Series II Wheel Dozer BPC00001-UP (MACHINE) »
230-1584
ALTERNATOR GP-CHARGING
Custom Product Support Literature for the 834G Series II Wheel Type Tractor and 836G Series II Landfill Compactor BPC00001-UP (MACHINE) »
230-1584
ALTERNATOR GP-CHARGING
836G Landfill Compactor BRL00001-UP (MACHINE) POWERED BY 3456 Engine »
230-1584
ALTERNATOR GP-CHARGING
834G Wheel Tractor BPC00001-UP (MACHINE) POWERED BY 3456 Engine »
230-1584
ALTERNATOR GP-CHARGING
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 456-7992 Tool - Puller (Injector) 1
B 8T-2998 Lubricant - Start By:
Remove the rocker arms and the rocker arm shaft.
Remove the fuel manifold (rail)
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03858297
Remove harness assembly (1) .
Illustration 2 g03851663
If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer.
Remove valve bridges (5). Note the location and orientation of the valve bridges for installation purposes.
Remove bolt (3) from clamp (4) .
Place an identification mark on electronic unit injector (2) for installation purposes. Each electronic unit injector must be reinstalled in the original location in the cylinder head.
Illustration 3 g03851718
Use Tooling (A) to remove the electronic unit injector and the clamp from the cylinder head.
Illustration 4 g03852013
Remove O-ring seal (7) and washer (6) from electronic unit injector (2) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install electronic unit injector (2) in the reverse order of removal.Note: Install electronic unit injector (2) into the original location in the cylinder head.
Lubricate O-ring seal (6) with Tooling (B) .
Tighten bolt (3) to a torque of 46 3 N m (34 2 lb ft).End By:
Install the fuel manifold (rail)
Install the rocker arms and the rocker arm shaft.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 456-7992 Tool - Puller (Injector) 1
B 8T-2998 Lubricant - Start By:
Remove the rocker arms and the rocker arm shaft.
Remove the fuel manifold (rail)
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g03858297
Remove harness assembly (1) .
Illustration 2 g03851663
If the injector hold down bolt is loose during the removal procedure, inspect the injector bore for wear and debris. Replace the clamp and spacer.
Remove valve bridges (5). Note the location and orientation of the valve bridges for installation purposes.
Remove bolt (3) from clamp (4) .
Place an identification mark on electronic unit injector (2) for installation purposes. Each electronic unit injector must be reinstalled in the original location in the cylinder head.
Illustration 3 g03851718
Use Tooling (A) to remove the electronic unit injector and the clamp from the cylinder head.
Illustration 4 g03852013
Remove O-ring seal (7) and washer (6) from electronic unit injector (2) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install electronic unit injector (2) in the reverse order of removal.Note: Install electronic unit injector (2) into the original location in the cylinder head.
Lubricate O-ring seal (6) with Tooling (B) .
Tighten bolt (3) to a torque of 46 3 N m (34 2 lb ft).End By:
Install the fuel manifold (rail)
Install the rocker arms and the rocker arm shaft.
Parts alternator Caterpillar catalog:
3501457
ALTERNATOR GP-CHARGING
C4.4, C4.4XQ100, C4.4XQ80
C4.4, C4.4XQ100, C4.4XQ80
2625046
ALTERNATOR GP-CHARGING
824H, 825H, 834H, 988H
824H, 825H, 834H, 988H
4308211
ALTERNATOR GP-CHARGING
793F, 793F CMD, 793F OEM
793F, 793F CMD, 793F OEM
6L6597
ALTERNATOR GROUP
D353C, G353D
D353C, G353D
3753358
ALTERNATOR GP-CHARGING
D6T LGP, D6T LGPPAT
D6T LGP, D6T LGPPAT
3054C, 3054E, 416D, 420D, 424D, 428D, 430D, 432D, 442D
3N7608
ALTERNATOR MOUNTING GROUP
D346, D348, D349
D346, D348, D349