ALTERNATOR GP-CHARGING 2895973 - Caterpillar

Illustration 20 g06306331
(3) 6V-8400 O-Ring Seal
(4) 523-7784 Hose As.
(14) 523-7785 Hose As.
(15) 6V-9854 Elbow
(16) 6V-8741 Union
(20) 5K-9090 O-Ring Seal
Install union (16) and O-ring (3) onto hose (4). Connect elbow (15) and O-ring (20) to the union, and connect hose (14) to the elbow. Connect the end of the hose with the straight coupling.
Illustration 21 g06306351
(R) 8T-5005 Bolt
(17) 8T-7934 Hard Washer
(18) 163-3098 Fitting
(19) 4J-0520 O-Ring Seal
(20) 5K-9090 O-Ring Seal
(21) 8C-3206 Half Flange
(22) 9J-3866 Adapter
Place adapter (22) and an O-ring (19) onto the pump. Place fitting (18) and an O-ring (19) onto the adapter. Secure the fitting with two half flanges (21), four saved bolts (R), and four washers (17).
Illustration 22 g06306371
(N) 164-5567 Quick Disconnect Coupler As
(P) 6V-0852 Dust Cap
(23) 241-6215 Elbow As
Install elbow (23) onto the pump. Install the saved quick disconnect coupling (N) and dust cap (P) on the elbow.
Illustration 23 g06306384
(14) 523-7785 Hose As.
(18) 163-3098 Fitting
(20) 5K-9090 O-Ring Seal
(24) 6V-9854 Elbow
(25) 6V-9840 Swivel Tee
Install elbow (24) onto fitting (18). Install two O-rings (20) on the top and bottom ports of swivel tee (25). Install the tee on the elbow. Connect hose (14) to the bottom of the tee.
Illustration 24 g06306420
(C) 8T-4195 Bolt
(D) 8T-4121 Hard Washer
(K) 5P-7468 Clip
(L) 5P-7469 Clip
(M) 5P-8444 Grommet
(5) 8T-4182 Bolt
(6) 8T-4121 Hard Washer
(7) 455-8433 Mount As
(8) 9L-8781 Washer
(9) 344-5675 Nut
(14) 523-7785 Hose As.
(26) 523-7783 Bracket
Place bracket (26) into position where the former bracket was removed. Install using saved bolt (C) and washer (D).
Install saved grommet (M), clip (K), and clip (L) onto hose (14). Secure the clips to bracket (26) using bolt (5), washer (6), mount (7) washer (8), and nut (9).
Illustration 25 g06306439
(27) 523-7786 Hose As.
Install hose (27) onto the tee.
Illustration 26 g06306448
(C) 8T-4195 Bolt
(D) 8T-4121 Hard Washer
(K) 5P-7468 Clip
(L) 5P-7469 Clip
(M) 5P-8444 Grommet
(27) 523-7786 Hose As.
(28) 150-3073 Plug As
(29) 561-3039 Bracket
Install bracket (29) onto the engine harness clamping next to the starter using the existing hardware. Install saved grommet (M) onto hose (27). Secure the hose to the bracket using saved clip (K), clip (L), bolt (C), and washer (D).
Install plug (28) onto hose (27).