3091280 ALTERNATOR GP-CHARGING Caterpillar parts
C9, TH31-E61
Rating:
Alternative (cross code) number:
CA3091280
309-1280
3091280
CA3091280
309-1280
3091280
INDUSTRIAL ENGINE, PETROLEUM TRANSMISSION,
Compatible equipment models: 3091280:
Number on catalog scheme:
For full view, you need register
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Note: Put identification marks on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps keep contaminants out of the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Swing the upper structure in order to gain access to the cover that is located under the cab.
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Illustration 1 g00854404
Remove bolts (2) and cover (1) .
Illustration 2 g01432111
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 3 g01435495
Disconnect harness assembly (3). Remove switch (4). Disconnect all hose assemblies (6) from implement pilot valve (5) .
Illustration 4 g01435505
Remove fittings (7) .
Illustration 5 g01435507
Remove bolt (9) and lever assembly (8) .
Illustration 6 g01435508
Remove bolts (10) and implement pilot valve (5) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Note: Put identification marks on all hose assemblies and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps keep contaminants out of the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Swing the upper structure in order to gain access to the cover that is located under the cab.
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "System Pressure - Release".
Illustration 1 g00854404
Remove bolts (2) and cover (1) .
Illustration 2 g01432111
Remove the cap from the hydraulic tank. Install Tooling (A) onto the hydraulic tank. Attach an air supply hose to Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 3 g01435495
Disconnect harness assembly (3). Remove switch (4). Disconnect all hose assemblies (6) from implement pilot valve (5) .
Illustration 4 g01435505
Remove fittings (7) .
Illustration 5 g01435507
Remove bolt (9) and lever assembly (8) .
Illustration 6 g01435508
Remove bolts (10) and implement pilot valve (5) .
Parts alternator Caterpillar catalog:
1673C, 3114, 3116, 3126, 3126B, 3176, 3176B, 3176C, 3196, 3208, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3408, 3408E, 3412E, 3456, 45, 55, AP-1000, AP-1050, C-10, C-12, C-15, C-16, C-9, C11, C13, C15,...
3116, 3126, 3126B, 3176B, 3176C, 3196, 3304, 3306, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, C-...
3126B, 3176C, 3196, 320B, 325B L, 330B L, 3412, 345B L, 350, 365B, 365B II, 539, 561M, 561N, 572R, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 825C, 825G, 825G II, 938G, 950G, 950G II, 95...
120H, 120H NA, 12H, 12H ES, 12H NA, 12M, 135H, 135H NA, 140G, 140H, 140H NA, 140M, 14H NA, 160H, 160H ES, 160M, 16H NA, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 324D FM, 324D FM LL, 32...
3406B, 3406C, 3412E, 3508B, 3512B, 3516B, 3516C, 583T, 587T, C-12, C11, C13, C15, C18, C27, C32, C7, C9, CX31-C13I, CX31-C15I, CX35-P800, D6R II, D6R III, D7R II, D8T, D9R, DEUCE, TH31-E61, TH35-C11I,...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M 2, 160M 3, 160M 3 AWD, 16M, 3512C, 725C, 730C, 735B, 740B, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F X...
120H, 120H ES, 12G, 12H, 12H ES, 135H, 135H NA, 140G, 140H ES, 16G, 16H NA, 3114, 3116, 3126B, 3176C, 3208, 330, 3304, 3306, 3306B, 330B L, 3406C, 3412, 3412C, 345B, 527, 528B, 530B, 583R, 587R, 589, ...
3126B, 322C, 324D, 324D L, 324D LN, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 3406E, 34...
120H, 120H ES, 120H NA, 12H ES, 12H NA, 135H NA, 140H ES, 140H NA, 143H, 14H NA, 160H ES, 160H NA, 163H NA, 16H NA, 3114, 3126B, 3176B, 3176C, 3196, 3306, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412...
3400707
ALTERNATOR GP-CHARGING
C11, C13, CX31-C13I, TH35-C11I, TH35-C13I
C11, C13, CX31-C13I, TH35-C11I, TH35-C13I
3117455
ALTERNATOR GP-CHARGING
C4.4, SPF343C
C4.4, SPF343C
2831309
ALTERNATOR GP-CHARGING
303.5C, 303.5D, 303C CR, 304D CR
303.5C, 303.5D, 303C CR, 304D CR
3767735
ALTERNATOR GP-CHARGING
330D, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
3715017
ALTERNATOR GP-CHARGING
C15, C32, C7, C9
C15, C32, C7, C9