3599426 ALTERNATOR AS Caterpillar parts
C7.1
Rating:
Alternative (cross code) number:
CA3599426
359-9426
3599426
CA3599426
359-9426
3599426
Weight: 12 pounds 5 kg.
GENERATOR SET,
Compatible equipment models: 3599426:
Number on catalog scheme:
4
For full view, you need register
Information:
Illustration 1 g02714481
Schematic of the Cat Data Link for770G, 772G and 777G Off-Highway Trucks, 773G and 775G Quarry Trucks
Illustration 2 g03859095
Schematic of the Cat Data Link for 777E and 773E Off-Highway Trucks
This diagnostic code is recorded when the VIMS ECM is not sending the necessary parameters to the Advisor ECM at the proper rate. The update rate for parameters that are generated by the VIMS ECM is not correct. The communication failure may be due to disconnected connectors or a faulty wiring harness.The possible causes of this diagnostic code are listed:
The VIMS ECM has the incorrect software installed.
The Advisor ECM has the incorrect software installed.
Incompatible software may be installed.
The fuse for the VIMS ECM may have failed.Test Step 1. CHECK THE VIMS ECM AND THE ADVISOR ECM FOR PROPER SOFTWARE VERSIONS.
Use Caterpillar Electronic Technician (ET) to verify that the versions of software are compatible.Expected Result:The proper versions of software are installed on the Advisor ECM and the VIMS ECM.Results:
YES - The versions of software are compatible. Proceed to Test Step 2.
NO - The proper software is not installed.Repair: Flash the proper software to the appropriate ECM. Cycle the key switch to initialize the new software. Ensure that the diagnostic code is no longer active.STOPTest Step 2. RECHECK FOR DIAGNOSTIC CODES.
Ensure that diagnostic code is active.Expected Result:The diagnostic code is inactive. The diagnostic code indicator is inactive.Results:
YES - The diagnostic code indicator and the diagnostic code are inactive.Repair: Clear the diagnostic code.STOP
NO - The diagnostic code is active.Repair: Ensure that the proper software is installed before replacing the ECM. If the software is correct, replace the Advisor ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". If the Advisor ECM was just replaced , install a new VIMS ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace" for the machine that is being serviced.STOP
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts alternator Caterpillar catalog:
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M 2, 160M 3, 160M 3 AWD, 16M, 3512C, 725C, 730C, 735B, 740B, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F X...
140H, 143H, 14H, 160H, 163H, 16H, 2384C, 2470C, 2484C, 2570C, 2670C, 2864C, 374F L, 390F L, 553C, 559C, 563C, 573C, 579C, 586C, 770G, 772G, 773F, 775F, 777C, 777D, 777F, 844H, 953D, 963D, 990H, AD55B,...
3500619
ALTERNATOR GP-CHARGING
C6.6, C7.1
C6.6, C7.1
C4.4, C4.4XQ100, C4.4XQ80, C7.1
C13, C7.1, C9.3, CX31-C13I
3218930
ALTERNATOR
C7.1
C7.1
C4.4, C7.1
312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L, C4.4, C7.1
3218940
ALTERNATOR
BG1000E, BG1055E, C6.6, C7.1, D6N LGP, D6N OEM
BG1000E, BG1055E, C6.6, C7.1, D6N LGP, D6N OEM
3238733
ALTERNATOR AS
C1.5, C2.2
C1.5, C2.2
3013C, 3024, 3024C, AP-255E, BB-621C, C1.5, C2.2, CB-214E, CB-22, CB-334E, CB-34
3013C, 3024, 3024C, AP-255E, BB-621C, C1.5, C2.2, CB-214E, CB-22, CB-334E, CB-34
2W5955
ALTERNATOR AS-CHARGING
G3304, G3306, G3406, G3408, G3606, G379, G398, G399
G3304, G3306, G3406, G3408, G3606, G379, G398, G399
1W0634
ALTERNATOR & GUARD AS
3408, 3408C, 3412, 3412C
3408, 3408C, 3412, 3412C