ALTERNATOR GP 5486882 - Caterpillar

Changes to Buttons, Dialogs, and Windows
Material Type Updated - In GIS mode, Material Type (MT) in Digital windows shows both Material ID and Block.GIS with History Windows - Operators can use the Truck Load History and the Dipper Load History windows when in GIS mode.Machine Configuration Utility (MCU) Release Notes
Note: The MCU Server/Client requires Microsoft .NET framework 4.5. If not installed, the MCU may not display your machines.Screen Configuration Utility (SCU) Release Notes
Installing SCU v6.2.1
When installing SCU v6.2.1, Windows may display a "Microsoft Visual C++ 2015 Redistributable (x86) - 14.0.24215" message. Select the "I agree" tick box and then select install. At the end of the SCU install, Windows may display a computer restart required message. Reboot the computer.System Troubleshooting
Table 3 outlines the corrective action for the listed trouble.
Table 3
System Troubleshooting
Trouble Description Corrective Action
The Sensor Diagnostics window does not show communication from the software to the AS4x0 sensor. The fault is intermittent. A loose solder joint or a loosely tightened plug breaks the connection. Solder or tighten the plug.
The AS4x0 does not consistently reconnect when unplugged and plugged in again. This symptom is often due to loose solder joints or a loose plug. Solder or tighten the plug.
Communication is delayed between the sensor and the on-board software. After fixing any fault with a connection to the sensor, the on-board software and the sensor may take up to 30 seconds to communicate. After 30 seconds, open the "Sensor Diagnostics" window to determine if the software has connected to the sensor. If not connected, cycle the power to restart the software, then recheck in the window. Reference Section
Firmware Matrix
The tables in this section capture the latest firmware versions that are supported by Terrain v6.2.1.
Table 4
Terrain On-board Software
Application Version
BIOS version G610 v29
Terrain for Grading and Loading
CAESultra Resource DLL - All languages 6.2.xxx
G610 version of XPe operating system Xpe v1.04
Terrain Installer TerrainInstaller.6.2.xxx
Table 5
CAES Office Software Versions
Application Version
CAT2 DB6
CAT DB Configurator
CAT Editor
CAT Reports NA(Not used for Command)
Terrain Office 2.0.3-7
Cat MineStar Office(Fleet and Detect) 5.1-21
MCU Server
MCU Client 6.2.xxx
Table 6
Utilities
Application Version
CGStestSuite.62 GNSS v0.72
Configuration Toolbox 6.9.0.5
Easy IP DNS 1.2 B1.0.0.64
MCG Flash Prod ver 1.17.0
MSControllerCAES (on-board) MSControllerCAES
TerrainDemo Installer TerrainDemo. 5.3.xxx.exe
Table 7
Angle Sensors
Device Version
AS450 2.29 or newer
AS460 2.29 or newer Receiver Firmware
Table 8 lists the minimum receiver firmware and the latest firmware that is packaged with the Terrain for grading and loading installer.
Table 8
Receiver Firmware
Receiver Minimum firmware version(1) Packaged with Terrain for grading and loading installer
MS35x Series
MS352 5.06
"MS9x2506.s"
MS9x0 Series
MS990 3.9 4.49/3.81
"MS990449.s"
MS9x2 Series
MS992
Single and Dual antenna 4.89/0.42 5.21
“MS9x2521.s”
MS952
MS972
MS9x5 Series
MS955 5.21MS9x2521.s
MS975
MS995
(1) First number listed is application firmware version, second number is monitor version