9L3787 ALTERNATOR MOUNTING AND DRIVE GROUP Caterpillar parts
1676
Rating:
Alternative (cross code) number:
CA9L3787
9L-3787
9L3787
CA9L3787
9L-3787
9L3787
Weight: 3 pounds 1 kg.
TRUCK ENGINE,
Compatible equipment models: 9L3787:
Number on catalog scheme:
For full view, you need register
Caterpillar SIS machinery equipment:
Information:
Priming the Fuel System
Low Pressure Side of Pump
1. OPEN the VENT VALVE, on the pump housing. 2. Unlock and OPERATE the HAND PRIMING PUMP until fuel flows free of air bubbles from the vent drain line. 3. CLOSE the drain valve. 4. LOCK the priming pump.High Pressure Side of Pump
If, after priming the low pressure system, the engine will not start, or runs rough after starting, the high pressure fuel lines must be primed.Each injection pump has a reverse flow check valve. These cannot be opened with hand priming pump pressure. Use the following procedure to prime the high pressure fuel lines: 1. LOOSEN each of the FUEL LINE NUTS, at the cylinder head end, 1/2 turn.2. To remove air in the injection lines, move the governor lever to LOW IDLE. Crank the engine. 3. When the fuel flows freely without bubbles, tighten nuts. Torque to 40.8 7 N m (30 5 lb. ft.).Ether Starting Aid - Changing Ether Cylinder
Ether is poison and flammable.Do not smoke while changing cylinder.Use only in well ventilated areas.Use with care to avoid fires.Do not store replacement ether cylinders in living areas or in operator's compartment - keep out of the reach of children.Avoid breathing of vapors or repeated contact with skin.Do not store cylinders at temperatures above 49°C (120°F).Do not use cylinders in environments above 93°C (200°F).Do not store cylinders in direct sunlight.Do not puncture or burn cylinders.Discard cylinders in a safe place.
1. Loosen clamp (1) and UNSCREW the ETHER CYLINDER (2).2. Remove the used gasket and install the new gasket provided with each new cylinder.3. Install the new cylinder. Use Caterpillar part number 7N296 as a replacement cylinder. Tighten the cylinder hand tight. Refasten the cylinder clamp securely around the cylinder.
Low Pressure Side of Pump
1. OPEN the VENT VALVE, on the pump housing. 2. Unlock and OPERATE the HAND PRIMING PUMP until fuel flows free of air bubbles from the vent drain line. 3. CLOSE the drain valve. 4. LOCK the priming pump.High Pressure Side of Pump
If, after priming the low pressure system, the engine will not start, or runs rough after starting, the high pressure fuel lines must be primed.Each injection pump has a reverse flow check valve. These cannot be opened with hand priming pump pressure. Use the following procedure to prime the high pressure fuel lines: 1. LOOSEN each of the FUEL LINE NUTS, at the cylinder head end, 1/2 turn.2. To remove air in the injection lines, move the governor lever to LOW IDLE. Crank the engine. 3. When the fuel flows freely without bubbles, tighten nuts. Torque to 40.8 7 N m (30 5 lb. ft.).Ether Starting Aid - Changing Ether Cylinder
Ether is poison and flammable.Do not smoke while changing cylinder.Use only in well ventilated areas.Use with care to avoid fires.Do not store replacement ether cylinders in living areas or in operator's compartment - keep out of the reach of children.Avoid breathing of vapors or repeated contact with skin.Do not store cylinders at temperatures above 49°C (120°F).Do not use cylinders in environments above 93°C (200°F).Do not store cylinders in direct sunlight.Do not puncture or burn cylinders.Discard cylinders in a safe place.
1. Loosen clamp (1) and UNSCREW the ETHER CYLINDER (2).2. Remove the used gasket and install the new gasket provided with each new cylinder.3. Install the new cylinder. Use Caterpillar part number 7N296 as a replacement cylinder. Tighten the cylinder hand tight. Refasten the cylinder clamp securely around the cylinder.
Parts alternator Caterpillar catalog:
6L6024
ALTERNATOR ASSEMBLY
1676, 3304, 3306
1676, 3304, 3306
1673, 1673B, 1673C, 1674, 1676, 1693
5D9953
ALTERNATOR ARRANGEMENT
621, 621B
621, 621B
1P4407
ALTERNATOR
594, 824B, D9G
594, 824B, D9G