APRON AS 2082977 - Caterpillar

2082977 APRON AS Caterpillar parts 621G, 627G

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2082977
208-2977
2082977

Weight: 2190 pounds 993 kg.

Buy APRON AS 2082977 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL SCRAPER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

KFBE Round Tablecloth 60 inch Cute Panda Table Cloth Cartoon Pattern Table Cover Heat-Resistant Washable Polyester for Dining Wedding Party Christmas 2082977

$21.99

04 Aug 2023

CN: KFBE

KFBE Round Tablecloth 60 inch Cute Panda Table Cloth Cartoon Pattern Table Cover Heat-Resistant Washable Polyester for Dining Wedding Party Christmas 2082977
KFBE Round Tablecloth 60 inch Size:60inch/152.4CM diameter with white lace 1.57inch/4CM || Eco-Friendly&Non-Toxic Materials:Made of soft polyester,Machine Washable and reusable. || Features: Environmental health material, comfortable feel, natural skin-friendly, anti-wrinkle and wear-resistant, unwiredrawn, high heat does not deform, with good water and oil repellent performance. || Multi Purpose Utilization:our tablecloth is perfect for wedding, birthday party, bridal or baby shower, candy buffet, Christmas,Halloween,exhibition event and other various parties. || Excellent Service: We offers excellent customer service.If you have any problem with our products,please feel free to let us know and we will solve it for you within 24 hours.

Number on catalog scheme: 3

Caterpillar 2082977 Parts scheme APRON AS

For full view, you need register

Compatible equipment models: 2082977:

WHEEL SCRAPER 621G 627G Caterpillar

Information:

Illustration 1 g02562918
Schematic of the proportional solenoid (Bowl raise)This diagnostic code is associated with the Proportional Solenoid (Bowl Raise). The FMI 06 means that the ECM has determined that the current of the solenoid is above normal. The possible causes of this diagnostic code are listed:
The energize circuit of the solenoid is shorted to ground.
The solenoid has failed.
The ECM has failed. The failure of ECM is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1275 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code occurs, a warning (Category 1) is shown on the monitor. The diagnostic code will cause the solenoid to be de-energized at all times. The bowl will not move up in response to a command. The bowl can be moved in a downward direction.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position.Note: Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness.Expected Result:CID 1275 FMI 06 changes to CID 1275 FMI 05 when the solenoid is disconnected.Results:
YES - CID 1275 FMI 06 changes to CID 1275 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid.STOP
NO - CID 1275 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J1-48 (wire R715-GN) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-48 (wire R715-GN) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1275 FMI 06.Expected Result:The CID 1275 FMI 06 is active.Results:
YES - The CID 1275 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again.