AVSPARE.COM
parts catalog

ARM 1P7304 - Caterpillar


1P7304 ARM Caterpillar parts 777
Rating:
41
Alternative (cross code) number:
CA1P7304
1P-7304
1P7304
Caterpillar 1P7304 ARM
Weight: 0.100 pounds 0 kg.

Buy ARM 1P7304 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compatible equipment models: 1P7304:

TRUCK  777   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:


Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Specifications
Table 1
D7E Brake Pressure Test    
Date     Product    
Item     Specification     Actual    
Engine speed     High Idle        
Pressure with the brakes ON (B1)     Less than
70 kPa (10 psi)        
Pressure with the brakes OFF (B1)     Greater than
2500 kPa (365 psi)        Introduction
The following test will determine if the pressure of the oil that is delivered to the service brakes from the brake valve is within the specified limit. Also, this test will determine whether the oil pressure to the brakes decreases to the specified limit when the brakes are activated.Note: Brake pressure is supplied by the steering charge pump. The steering charge pump is part of the hydraulic oil system.Required Tools
Illustration 1 g02571852
Tooling (A) 198-4240 Digital Pressure Indicator Gp
Table 2
Required Tools    
Tool    Item    Qty    Part No    Description    
A         198-4240     Digital Pressure Indicator Gp    
    A1     1     198-4234     Digital Indicator    
A2 1     198-4237     Pressure Sensor Gp
(0 to 3,445 kPa (0 to 500 psi))    
A3 1     198-4236     Adapter Cable As    Test Preparation
Move the machine to a smooth horizontal location.
Use suitable lifting devices in order to lift the machine. The tracks must be able to turn freely in both directions.
Place the steering control lever in the NEUTRAL position.
Engage the parking brake.
Lower the attachments to the ground.
Stop the engine.
Turn the key to the ON position, but do not start the engine.
Verify that the implement lockout switch is in the UNLOCKED position.
Move the control levers through the full range of travel several times. This procedure should relieve any pressure that may be present in the implement hydraulic system.
Make sure that the pressure in the entire hydraulic system has been released.
Turn the key to the OFF position.
Observe the state of the amber hazardous voltage present lamp. If the lamp is illuminated, do not perform any type of service on the machine. Wait until the lamp is not illuminated. Then, perform the lamp test in the next step.
While you observe the lamp, turn the disconnect switch to the OFF position. Then turn the disconnect switch to the ON position.Note: When the disconnect switch is cycled, the amber hazardous voltage present lamp will illuminate briefly. Then, the lamp will turn off indicating that the operation of the lamp is correct.
If an error message for the lamp circuit is displayed, or if the operation of the hazardous voltage present lamp does not appear to be correct, refer to the Troubleshooting, "General Information" section of the manual for information on troubleshooting the lamp circuit.
Once the hazardous voltage level has been

Caterpillar parts catalog:

Caterpillar parts catalog
777 TRUCK 84A00001-01283 (MACHINE) POWERED BY D348 ENGINE
776 TRACTOR 14H00001-00205 (MACHINE) POWERED BY D348 ENGINE
D10 TRACTOR 76X00001-00358 (MACHINE) POWERED BY D348 ENGINE
D10 TRACTOR / POWER SHIFT / 76X00359-UP (MACHINE) POWERED BY D348 ENGINE
777 TRUCK 84A01284-UP (MACHINE) POWERED BY D348 ENGINE
776 TRACTOR 14H00206-UP (MACHINE) POWERED BY D348 ENGINE
777 TRUCK 84A00001-01283 (MACHINE) POWERED BY D348 ENGINE
776 TRACTOR 14H00001-00205 (MACHINE) POWERED BY D348 ENGINE
D10 TRACTOR 76X00001-00358 (MACHINE) POWERED BY D348 ENGINE
D10 TRACTOR / POWER SHIFT / 76X00359-UP (MACHINE) POWERED BY D348 ENGINE
777 TRUCK 84A01284-UP (MACHINE) POWERED BY D348 ENGINE
776 TRACTOR 14H00206-UP (MACHINE) POWERED BY D348 ENGINE


Parts arm Caterpillar catalog:

5T9034 ARM AS-WIPER
769C, 771C, 773B, 775B, 776C, 777
2G3724 ARM
769C, 771C, 772B, 773B, 775B, 776, 776C, 777, 777B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.