2624839 ARM & BEARING AS-LIFT Caterpillar parts
992G
Rating:
Alternative (cross code) number:
CA2624839
262-4839
2624839
CA2624839
262-4839
2624839
Weight: 14200 pounds 6441 kg.
WHEEL LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2018-03-13
2017-01-09
Compatible equipment models: 2624839:
Information:
Illustration 8 g00817741
Cut tie strap (22) which secures the wiring harness to the guide for the oil level gauge. Remove the boot and the wiring harness from terminal (23) on the air inlet heater.
Illustration 9 g00817747
Remove bolt (24) and the spacer. Remove screw (25) and the two wires.
Illustration 10 g00817749
Disconnect two electrical plugs (26) and (26a). Remove the boot, the nut and the wire from terminal (27) on the alternator.
Illustration 11 g00817744
Disconnect electrical plug (28). Loosen bolt (29). The bolt cannot be removed because of interference with the air conditioner lines. Remove bolts (30) .
Illustration 12 g00817753
Disconnect electrical plug (31). Remove two screws from switch (32), and cut four tie straps (33) .
Illustration 13 g00817757
Pull back the boot from the terminal (34). Remove the nut and two wires. Remove bolt (35), the spacer and the clip from the wiring harness. Remove screw (36) and the plastic cover from the starter.
Illustration 14 g00817760
Remove screw (37), and remove the wire.
Illustration 15 g00817764
Disconnect electrical plug (38). Remove bolt (39 ), washers and spacers (40) which secure battery cables (41) .
Illustration 16 g00817768
Remove sheet assembly (42) from below the engine. The component is part of the bottom guard group.
Illustration 17 g00817775
Remove two cable clips (43), and remove four tie straps (45). Remove sheet (44), upper sheet assembly (46), and lower sheet assembly (47) .
Illustration 18 g00817771
Illustration 19 g00817789
Install Tooling (A), (B), (C) and (D). Refer to Illustrations 18 and 19. The weight of the pump is approximately 136 kg (300 lb).
Illustration 20 g00817792
Remove bolts (48) which secure the main hydraulic pump to the engine flywheel housing.
Illustration 21 g00817796
Attach a suitable lifting device to the engine. The engine weighs approximately 395 kg (870 lb). Mark the locations of the motor mounts for installation purposes. Remove four motor mounts (49). Lift the engine from the machine.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts arm Caterpillar catalog:
2147636
ARM GP-WINDOW WIPER
844, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G, 938G II, 938H, 990, 990 II, 990H, 992G, 992K, 994F, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663...
844, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G, 938G II, 938H, 990, 990 II, 990H, 992G, 992K, 994F, CP-433E, CP-44, CP-533E, CP-54B, CP-56, CP-573E, CP-64, CP-663...
2147635
ARM GP-WINDOW WIPER
554, 564, 574B, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 844, 844H, 854G, 854K, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II,...
554, 564, 574B, 824G II, 824H, 824K, 825G II, 825H, 825K, 826G, 826G II, 826H, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 844, 844H, 854G, 854K, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G, 966G II,...
1852155
ARM AS-WIPER
814F, 814F II, 815F, 815F II, 816F, 816F II, 844, 844H, 854G, 854K, 990 II, 990H, 992G, 992K, 994F
814F, 814F II, 815F, 815F II, 816F, 816F II, 844, 844H, 854G, 854K, 990 II, 990H, 992G, 992K, 994F
2429531
ARM & BEARING AS
HA771, HA871, TK371, TK381
HA771, HA871, TK371, TK381
2466279
ARM AR-LIFT
994F, 994H
994F, 994H
2698594
ARM GP-LIFT
420D
420D
2425308
ARM AS-LIFT
420D
420D
2357301
ARM & BEARING AS-LIFT
928HZ, 930G
928HZ, 930G
3544314
ARM AS-LIFT
980H
980H
3544313
ARM AS-LIFT
980H
980H
2343090
ARM AS-LIFT
980G II, 980H
980G II, 980H