6D7337 ARM ASSEM. (R.H.) Caterpillar parts
120, 120B, 12E
Rating:
Alternative (cross code) number:
CA6D7337
6D-7337
6D7337
CA6D7337
6D-7337
6D7337
Weight: 32 pounds 14 kg.
MOTOR GRADER,
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02898881
Illustration 2 g02898938
If necessary, remove the Original Equipment Manufacturer's (OEM) driven equipment from accessory drive (4). Refer to the OEM for the correct procedure.
If the OEM driven equipment was not installed onto accessory drive (4). Remove cover plate (2) and remove gasket (3) (not shown).
Remove Allen head bolts (6) from accessory drive (4). Remove the accessory drive housing from the front housing.
Remove O-ring seals (7) from the accessory drive. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound 1
B - Loctite 506 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the bore in the front housing for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.
Illustration 3 g02898938
Illustration 4 g02898881
Install new O-ring seals (7) onto accessory drive (4).
Apply Tooling (A) onto O-ring seals (7).
Install accessory drive (4) to housing (5).
Apply Tooling (B) onto the threads of Allen head bolts (6).
Install Allen head bolts (6) to accessory drive (4).
Equally tighten the Allen head bolts (6) in order to pull accessory drive (4) into housing (5).
Tighten Allen head bolts to a torque of 25 N m (221 lb in).
Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
If necessary, install the OEM driven equipment to accessory drive (4). Refer to the OEM for the correct procedure.
If the OEM driven equipment was not installed onto accessory drive (4), position new gasket (3) (not shown) and cover plate (2) onto accessory drive (4).
Apply Tooling (B) onto the threads of bolts (1).
Install bolts (1) to cover plate (2). Tighten the bolts to a torque of 25 N m (221 lb in).
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02898881
Illustration 2 g02898938
If necessary, remove the Original Equipment Manufacturer's (OEM) driven equipment from accessory drive (4). Refer to the OEM for the correct procedure.
If the OEM driven equipment was not installed onto accessory drive (4). Remove cover plate (2) and remove gasket (3) (not shown).
Remove Allen head bolts (6) from accessory drive (4). Remove the accessory drive housing from the front housing.
Remove O-ring seals (7) from the accessory drive. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6396 O-Ring Assembly Compound 1
B - Loctite 506 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Inspect the bore in the front housing for damage. If necessary, replace the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove" and Disassembly and Assembly, "Housing (Front) - Install" for the correct procedure.
Illustration 3 g02898938
Illustration 4 g02898881
Install new O-ring seals (7) onto accessory drive (4).
Apply Tooling (A) onto O-ring seals (7).
Install accessory drive (4) to housing (5).
Apply Tooling (B) onto the threads of Allen head bolts (6).
Install Allen head bolts (6) to accessory drive (4).
Equally tighten the Allen head bolts (6) in order to pull accessory drive (4) into housing (5).
Tighten Allen head bolts to a torque of 25 N m (221 lb in).
Ensure that there is tactile backlash between the idler gear and the accessory drive gear.
If necessary, install the OEM driven equipment to accessory drive (4). Refer to the OEM for the correct procedure.
If the OEM driven equipment was not installed onto accessory drive (4), position new gasket (3) (not shown) and cover plate (2) onto accessory drive (4).
Apply Tooling (B) onto the threads of bolts (1).
Install bolts (1) to cover plate (2). Tighten the bolts to a torque of 25 N m (221 lb in).
Caterpillar parts catalog:
Parts arm Caterpillar catalog:
120, 120B, 12E
120, 12E, 12F, 140B
4D2702
ARM
120B, 12E, 140B
120B, 12E, 140B
4D2671
ARM
120B, 12E, 140B
120B, 12E, 140B
2D7380
ARM
12E, 16
12E, 16
4D7293
ARM
12E
12E
120, 120B, 12E
120B, 12E, 12F, 140, 140B, 14E
6D8179
ARM ASSEM.
12F, 14E
12F, 14E
5D1823
ARM
12E, 12F, 14E
12E, 12F, 14E
4D1477
ARM ASSEM.
120B, 12E
120B, 12E
2D5318
ARM ASSEM. (MALE)
120G, 12E, 12F, 140, 14E, 16
120G, 12E, 12F, 140, 14E, 16
5D1344
ARM ASSEM.
120G, 12E, 12F, 140, 14E, 16
120G, 12E, 12F, 140, 14E, 16
5D1343
ARM ASSEM.
120G, 12E, 12F, 140, 14E, 16
120G, 12E, 12F, 140, 14E, 16
120, 120B, 12E