2310705 AXLE GP-DRIVE & STEERING Caterpillar parts
416D, 420D, 424D, 428D, 432D, 442D
Rating:
Alternative (cross code) number:
CA2310705
231-0705
2310705
CA2310705
231-0705
2310705
Weight: 910 pounds 412 kg.
BACKHOE LOADER,
Information:
Illustration 1 g00487533
The spare output on the GSC is strictly for the use of customers. The spare output is programmable in order to activate under a variety of conditions. The default parameter programming causes the GSC to activate the output when the engine is in cooldown mode. The GSC treats a CID 0334 FMI 04 as an alarm fault. For more information, see Systems Operation, "Spare Input/Output Programming OP6". The customer and/or the dealer are responsible for documenting and troubleshooting any connections to this output.The voltage on the spare output is approximately 5.0 DCV when there are no connections and when the spare output is not active. When the spare output is active, the voltage on the spare output is approximately 0 volts. The spare output is capable of drawing (sinking) approximately 100 mA.The possible cause of a CID 0334 FMI 04 is a short to the negative battery of the spare output signal.Troubleshooting of a spare output fault is direct. The FMI defines the fault. An FMI 04 occurs when the spare output is shorted to battery"B-". In order to find the exact cause of the fault, use the following information.
FMI information
system schematic of spare output
documentation of the customer
documentation of the dealerTest Step 1. CHECK THE GENERATOR SET CONTROL
Verify that the CID 0334 FMI 04 diagnostic code is active.
Disconnect the wire from contact 36 of the GSC.
Measure the voltage between contact 36 of the GSC and frame ground.Expected Result:The voltage is approximately 5 1.0 DCV.Results:
OK - The voltage is approximately 5 1.0 DCV. The voltage is correct. Proceed to test step 2.
NOT OK - The voltage is NOT approximately 5 1.0 DCV. The voltage is NOT correct. The GSC has failed.Repair: It is unlikely that the GSC has failed. Exit this diagnostic code procedure and repeat the CID 0334 FMI 04 diagnostic code procedure again. If the cause of the failure is still unknown, then replace the GSC. Stop.Test Step 2. CHECK FOR A SHORT TO "B-" IN THE WIRING OF THE SPARE OUTPUT
Disconnect the "B-" terminal from the battery.
Disconnect the wire from contact 36 of the GSC.
Disconnect the other end of the wire at the customer device.
Measure the resistance between the wire that was disconnected from contact 36 of the GSC and the "B-" contact of the GSC.Expected Result:The resistance is greater than 5000 ohms.Results:
OK - The resistance is greater than 5000 ohms. The circuit is correct. 3
NOT OK - The resistance is less than 5000 ohms. The circuit is not correct. The spare output is shorted to negative battery"B-" .Repair: Repair the wiring of the spare output. Stop.Test Step 3. RECONNECT TO THE CUSTOMER DEVICE
Reconnect the wire to the customer device.
Reconnect the wire from contact 36 to the GSC.
Turn the switch for the ESC to STOP and check if the diagnostic code is still active.Expected Result:The diagnostic code is not active.Results:
OK - The diagnostic code is not active. It is likely that the problem was in the wiring harness or the problem is
Caterpillar SIS machinery equipment:
Caterpillar SIS
416D Backhoe Loader BGJ00523-01315 (MACHINE) POWERED BY 3054 Engine »
231-0705
AXLE GP-DRIVE & STEERING
420D Backhoe Loader BKC00502-UP (MACHINE) POWERED BY 3054 Engine »
231-0705
AXLE GP-DRIVE & STEERING
420D Backhoe Loader BMC00611-UP (MACHINE) POWERED BY 3054 Engine »
231-0705
AXLE GP-DRIVE & STEERING
442D Backhoe Loader SMJ00001-UP (MACHINE) POWERED BY 3054C Engine »
231-0705
AXLE GP-DRIVE & STEERING
424D Backhoe Loader CJZ00001-UP (MACHINE) POWERED BY 3054C Engine »
231-0705
AXLE GP-DRIVE & STEERING
428D Backhoe Loader BXC00001-UP (MACHINE) POWERED BY 3054C Engine »
231-0705
AXLE GP-DRIVE & STEERING
428D Backhoe Loader MBM00001-UP (MACHINE) POWERED BY 3054C Engine »
231-0705
AXLE GP-DRIVE & STEERING
432D Backhoe Loader TDR00001-UP (MACHINE) POWERED BY 3054C Engine »
231-0705
AXLE GP-DRIVE & STEERING
Caterpillar parts catalog:
Parts axle Caterpillar catalog:
1198190
AXLE GP-DRIVE & STEERING
426C, 436C, 438C, 438D, 442D
426C, 436C, 438C, 438D, 442D
1545465
AXLE GP-FRONT
416C, 416D, 420D, 424D, 426C, 428C, 430D, 436C
416C, 416D, 420D, 424D, 426C, 428C, 430D, 436C
1140165
AXLE & MTG GP-REAR
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1891834
AXLE GP-FRONT
416D, 420D, 424D, 430D
416D, 420D, 424D, 430D
1545472
AXLE GP-DRIVE & STEERING
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1562857
AXLE GP-REAR
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
416C, 416D, 420D, 424D, 426C, 428C, 428D, 432D, 436C, 438C, 438D, 442D
1562853
AXLE GP-REAR
416C, 416D, 420D, 426C, 430D, 436C
416C, 416D, 420D, 426C, 430D, 436C
1073716
AXLE & MTG GP-REAR
416C, 416D, 420D, 426C, 430D, 436C
416C, 416D, 420D, 426C, 430D, 436C
1863462
AXLE GP-DRIVE & STEERING
416D, 420D, 424D, 428D, 432D, 438D, 442D
416D, 420D, 424D, 428D, 432D, 438D, 442D
1693242
AXLE AS
416C, 416D, 420D, 424D, 426C, 428C, 430D, 436C
416C, 416D, 420D, 424D, 426C, 428C, 430D, 436C
1294280
AXLE AR-FIXED
966G, 966G II, 966H, 966K, 972G, 972G II
966G, 966G II, 966H, 966K, 972G, 972G II
1756262
AXLE & MTG GP-DRIVE
CP-433C
CP-433C
9R1310
AXLE GP-FRONT
446, 446B, 446D
446, 446B, 446D
2517571
AXLE AR-FIXED
972G II, 972H
972G II, 972H
1959693
AXLE AR-FIXED
938G, IT38G
938G, IT38G
2116604
AXLE GP-DRIVE
CP-573E, CP-663E, CS-663E, CS-683E
CP-573E, CP-663E, CS-663E, CS-683E
8I6430
AXLE GP-REAR
TH103
TH103
1831142
AXLE AR-OSCILLATING
966G, 966G II, 966H
966G, 966G II, 966H
1191082
AXLE AR-FIXED
814F, 814F II, 816F
814F, 814F II, 816F