4364759 AXLE GP-STEERING Caterpillar parts
MH3037
Rating:
Alternative (cross code) number:
CA4364759
436-4759
4364759
CA4364759
436-4759
4364759
MATERIAL HANDLER,
This part in 4 request:
Show.
This information for suppliers only!
2023-09-04
2022-12-08
2020-11-25
2020-02-20
Compatible equipment models: 4364759:
For full view, you need register
Information:
Transmission Clutch Engagement Pressure Calibration (Using Caterpillar Electronic Technician)
Use the ET in order to calibrate the transmission clutch pressures. The procedures are performed in order to compensate for variations in the transmission components.Note: The torque converter lockup clutch calibration procedure is performed during the calibration procedure for the seven transmission clutches.Calibration is required in the following situations:
Before dealer delivery to the customer.
After replacing the transmission ECM
After replacing or servicing any of the ECPC valves or the main relief valve
After replacing or rebuilding the transmission or torque converter
After replacing the transmission control charge pump
Degradation in shift qualityThe transmission ECM must detect the following conditions before starting the calibration procedure:
The parking brakes are ENGAGED.
The service brakes are RELEASED.
The engine speed is at low idle (approximately 700 rpm).
The gear selector is in the PARK position.
The transmission oil temperature is above 70 °C (158 °F) and below 85 °C (185 °F).
The transmission output speed (TOS) is 0 rpm.
There are no active clutch solenoid diagnostic codes.
There are no active transmission or torque converter speed sensor diagnostic codes.
There are no active transmission or torque converter temperature sensor diagnostic codes.If any of these conditions are not met during the calibration, the procedure is aborted immediately.The sustain pressure calibration requires pressure gauges to measure the actual pressure in the clutch. The Data View diagnostic tool should be used when possible. Eight pressure gauges should be installed before the calibration procedure begins. The transmission ECPC valve pressure taps are located on the cover of the transmission and the lockup clutch (LUC) ECPC is located on the torque converter case.
Illustration 1 g01283296
ET Calibration ScreenUse the Cat ET to calibrate the transmission clutch pressures. Select the "CALIBRATION" option from the Service Menu in Cat ET. Follow the instructions that are provided. Use the Cat ET in order to increase the individual pressure of the clutch. Use the Cat ET in order to decrease the individual pressure of the clutch. The pressure changes can be viewed on the pressure gauge.
Use the ET in order to calibrate the transmission clutch pressures. The procedures are performed in order to compensate for variations in the transmission components.Note: The torque converter lockup clutch calibration procedure is performed during the calibration procedure for the seven transmission clutches.Calibration is required in the following situations:
Before dealer delivery to the customer.
After replacing the transmission ECM
After replacing or servicing any of the ECPC valves or the main relief valve
After replacing or rebuilding the transmission or torque converter
After replacing the transmission control charge pump
Degradation in shift qualityThe transmission ECM must detect the following conditions before starting the calibration procedure:
The parking brakes are ENGAGED.
The service brakes are RELEASED.
The engine speed is at low idle (approximately 700 rpm).
The gear selector is in the PARK position.
The transmission oil temperature is above 70 °C (158 °F) and below 85 °C (185 °F).
The transmission output speed (TOS) is 0 rpm.
There are no active clutch solenoid diagnostic codes.
There are no active transmission or torque converter speed sensor diagnostic codes.
There are no active transmission or torque converter temperature sensor diagnostic codes.If any of these conditions are not met during the calibration, the procedure is aborted immediately.The sustain pressure calibration requires pressure gauges to measure the actual pressure in the clutch. The Data View diagnostic tool should be used when possible. Eight pressure gauges should be installed before the calibration procedure begins. The transmission ECPC valve pressure taps are located on the cover of the transmission and the lockup clutch (LUC) ECPC is located on the torque converter case.
Illustration 1 g01283296
ET Calibration ScreenUse the Cat ET to calibrate the transmission clutch pressures. Select the "CALIBRATION" option from the Service Menu in Cat ET. Follow the instructions that are provided. Use the Cat ET in order to increase the individual pressure of the clutch. Use the Cat ET in order to decrease the individual pressure of the clutch. The pressure changes can be viewed on the pressure gauge.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts axle Caterpillar catalog:
3954405
AXLE GP-REAR
MH3037
MH3037
4364760
AXLE AR-REAR
MH3037
MH3037
MH3037
3954404
AXLE GP-STEERING
MH3037
MH3037
4364910
AXLE GP-STEERING
MH3037
MH3037
MH3037
4364336
AXLE
MH3037
MH3037
3954404
AXLE GP-STEERING
MH3037
MH3037
MH3037
4364760
AXLE AR-REAR
MH3037
MH3037
3869386
AXLE AR-FIXED
R1600H
R1600H
MH3037
4364910
AXLE GP-STEERING
MH3037
MH3037