AXLE GP-FRONT 4542286 - Caterpillar

4542286 AXLE GP-FRONT Caterpillar parts

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA4542286
454-2286
4542286

Weight: 874 pounds 396 kg.

Buy AXLE GP-FRONT 4542286 Caterpillar genuine, new aftermarket tractor parts with delivery

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Wildcat 700 Front & Rear Brake Pads 2014-2017 Semi-Metallic Bike Pad Front brake pads Rear brake pads Replacement brake kits Brake Quad bike Replacement brake pads Parts Braking Detail

$48.21

20 Oct 2022
33.4[15.03] Pounds
CN: qjembhx shop

Wildcat 700 Front & Rear Brake Pads 2014-2017 Semi-Metallic Bike Pad Front brake pads Rear brake pads Replacement brake kits Brake Quad bike Replacement brake pads Parts Braking Detail
AIKLA 2014-2017 700 Wildcat Spare parts Spare brake pads Part Motorcycle Bike || You will receive 4 sets of brake pads || Replacing the front & rear brakes.

Draeger 4542286 X-am 2500 Gas Detector, alkaline Ex/H2S-LC

$1,291.50

29 Mar 2020

-: -

Draeger 4542286 X-am 2500 Gas Detector, alkaline Ex/H2S-LC

This part in 1 request: Show. This information for suppliers only!

#1529652 4542286

2025-04-28

Number on catalog scheme:

Caterpillar 4542286 Parts scheme AXLE GP-FRONT

For full view, you need register

Information:

Table 1
Diagnostic Trouble Code
J1939 Code Code Description Comments
3242-15 Particulate Trap Intake Gas Temperature : High - least severe (1) There are no active 168 diagnostic codes.
The Aftertreatment Regeneration Device (ARD) has been running for at least 30 seconds. The temperature at the intake of the DPF rises above a temperature that is calculated by the ECM. The temperature threshold has been exceeded for 60 seconds.
The code is logged. The code remains active until electrical power to the ECM is cycled.
3242-16 Particulate Trap Intake Gas Temperature : High - moderate severity (2) There are no active 168 diagnostic codes.
The Aftertreatment Regeneration Device (ARD) has been running for at least 30 seconds. The temperature at the intake of the DPF rises above
690° C (1274° F) and the temperature then remains above
680° C (1256° F) for 60 seconds. These values are configurable.
Active regeneration is immediately disabled. Engine power is derated. The code is logged. The code remains active until electrical power to the ECM is cycled.
Follow the troubleshooting procedure in order to identify the root cause of the fault. Troubleshooting Procedure
Related Systems
Troubleshoot any faults that relate to the following systems or conditions:
Low output pressure from the turbochargers
Aftertreatment Regeneration Device (ARD)
NOx Reduction System (NRS)Troubleshoot the systems in the order that is listed above if there are faults in more than one of the systems. If no faults are apparent, refer to "DPF".DPF
Remove the inlet section from the DPF. Inspect the inside of the inlet section and the front face of the DPF for excessive ash.A small amount of ash is a normal condition. If the amount of ash is considered to be excessive, contact the Caterpillar technical communicator. Continue with this procedure after guidance has been received.
Inspect the inside of the inlet section and the front face of the DPF for oil.If oil is found, inspect the outlet of the turbochargers. If oil is found, contact the technical communicator at a Caterpillar dealer. Continue with this procedure after guidance has been received.
Clean the oil from the inside of the inlet section of the DPF and the front face of the DPF. Assemble the DPF. Run the engine for 15 minutes.Electronic Unit Injectors
If no oil is found in the previous test step, leave the inlet section disconnected from the DPF. Use the electronic service tool to disable the ARD. Set the value of the "Data Link ARD Disable Status" configuration parameter to "