AXLE GP-OSCILLATING 8X0134 - Caterpillar

Fabrication and Installation Instructions
Fabricating the Hose Assemblies
Cut hose (8) into the seven lengths that are specified in Table 3.
Table 3
Hose Lengths    
Hose    Qty    PC6 Cold Planers    PC9 Cold Planers    
A     2    
80 mm (3.0 inch)    
105 mm (4.0 inch)    
B     1    
137 mm (5.4 inch)    
185 mm (7.3 inch)    
C     2    
60 mm (2.4 inch)    
76 mm (3.0 inch)    
D     1    
114 mm (4.5 inch)    
155 mm (6.0 inch)    
E     1    
2400 mm (94.5 inch)    
Illustration 1 g03661702
Fabrication details for Hose Assembly (N) (A) Hose (B) Hose (C) Hose (D) Hose (2) 124-6256 Hose Clamp (4) 173-7549 Tee (5) 173-7551 Elbow
Fabricate hose assembly (N) by connecting components as shown.
Illustration 2 g03661741
Fabrication details for hose (E) (E) Hose (1) 006-6586 Hose Connector (2) 124-6256 Hose Clamp (3) 173-7492 Coupling
Install components to hose (E) .Installing the Water Spray Kit
Illustration 3 g03661759
Details for drilled holes
Table 4
Drilled Holes    
Dimension    PC6 Cold Planers    PC9 Cold Planers    
F    
14 mm (0.5 inch)    
G    
100 mm (4.0 inch)    
140 mm (5.5 inch)    
H    
252 mm (10.0 inch)    
340 mm (13.4 inch)    
J    
402 mm (16.0 inch)    
540 mm (21.3 inch)    
K    
531 mm (21.0 inch)    
710 mm (28.0 inch)    
L    
75 mm (3.0 inch)    
M    
50 mm (2.0 inch)    
Drill six holes that are 17.5 mm (0.7 inch) in diameter. See Illustration 3 and Table 4 for the locations.
Place the hose assembly (N) so that the threaded ends of the six connectors are extended through the six drilled holes.
Access the threaded end of the connectors through the inspection door that is located on the top of the cold planer.
Install a nozzle (7) in each of the six connectors from the inside of the cold planer. Install retainers (6) in order to secure nozzles (7) in the connectors.Note: The installation of retainers (6) will also secure the connectors to the cold planer.
Illustration 4 g03661793
Installation of the hose assemblies (N) Hose Assembly (E) Hose Assembly (1) 006-6586 Hose Connector (4) 173-7549 Tee
Install hose assembly (E) to hose assembly (N). The threaded end of hose connector (1) on hose assembly (E ) is connected to tee (4), which is the middle connector on hose assembly (N) .
Illustration 5 g03661805
Installation of the hose assemblies (E) Hose Assembly (3) 173-7492 Coupling (9) 7K-1181 Cable Strap
Route hose assembly (E) along the hydraulic hoses. Secure hose assembly (E) to the hydraulic hoses with cable straps (9) .
Attach the quick connect coupler (3) on hose assembly (E) to the connector on the lift arm.
Adjust the nozzles for the correct spray pattern. Adjust the nozzles that are