BAFFLE 2584287 - Caterpillar

2584287 BAFFLE Caterpillar parts 246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2584287
258-4287
2584287

Weight: 0.22 pounds 0 kg.

Buy BAFFLE 2584287 Caterpillar genuine, new aftermarket tractor parts with delivery
COMPACT TRACK LOADER, SKID STEER LOADER,

Compatible equipment models: 2584287:

COMPACT TRACK LOADER 279C 279C2 289C 289C2 299C

MULTI TERRAIN LOADER 277C 277C2 287C 287C2 297C

SKID STEER LOADER 246C 256C 262C 262C2 272C Caterpillar

Number on catalog scheme: 4

For full view, you need register

Information:

Illustration 1 g01065561
Schematic of the Detent Coil (Tilt Back)This diagnostic code is associated with the Detent Coil (Tiltback). The FMI 06 means that the ECM has determined that there is a short to ground in the solenoid circuit. The possible causes of this diagnostic code are listed:
The internal windings for the detent coil have low impedance.
The internal windings for the detent coil are shorted.
The signal circuit from the ECM to the detent coil is shorted to ground.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0361 FMI 06 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The tiltback detent coil cannot be energized resulting in loss of tiltback kickout feature.The control is unable to hold lever in detent position.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Observe the status of the diagnostic code.
Disconnect the solenoid with the active diagnostic code from the machine harness. Expected Result:CID 0361 FMI 06 changes to CID 0361 FMI 05 when the solenoid is disconnected.Results:
YES - CID 0361 FMI 06 changes to CID 0361 FMI 05 when the solenoid is disconnected. The circuit is correct.Repair: The solenoid has failed. Repeat this test "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Stop.
NO - CID 0361 FMI 06 remains active. Proceed to Test Step 2.Test Step 2. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO GROUND.
Turn the key start switch and the disconnect switch to the OFF position.
The solenoid remains disconnected from the machine harness.
Disconnect the machine harness connector(s) from the ECM.
At the machine harness connector, measure the resistance from the signal contact J2-13 (wire H720-BU) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J2-13 (wire H720-BU) and the circuit with the low resistance measurement.Repair: Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the harness connectors and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 0361 FMI 06. Expected Result:The CID 0361 FMI 06 is active. Results:
YES - The CID 0361 FMI 06 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is