1F8359 BALL Caterpillar parts
12E, 311, 311B, 312, 312B, 315, 315B, 315B FM L, 317, 69D, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 773F, 775B, 775D, 775E, 775F, 776C, 776D, 777, 777D, 777F, 784B, 784C, 785, 785B, 785C, 7...
Rating:
Alternative (cross code) number:
CA1F8359
1F-8359
1F8359
CA1F8359
1F-8359
1F8359
Weight: 0.15 pounds 0 kg.
EXCAVATOR, UNDERCARRIAGE,
Compatible equipment models: 1F8359:
Information:
Procedure
Table 1
Troubleshooting Test Steps Values Results
1. Identify Any Active Code Associated With The Circuit Voltage
A. Connect Cat® Electronic Technician (Cat ET) Service Tool.
B. Check for codes.
No codes present.
OK - No codes present.
Go to Step 2.
Not OK - Code is present.
Go to the test procedure for that code.
STOP.
2. Check Connections And Harness
A. Inspect the circuit harness connectors(1).
B. Inspect the harness.
A. Connectors are:
* Clean
* Secure
* In good condition
B. Harness is not:
*Kinked
*Chafed
OK - Connections and harness are good.
Go to Step 3.
Not OK - A connection problem exists.
Repair:
A. Clean and secure connectors(1).
B. Verify that the problem is corrected.
STOP.
3. Check The System Voltage At The Display Module
A. Turn Start switch and Disconnect switch ON.
B. Disconnect the harness from the display.
C. At the display harness connector, insert one 7X-1710 Multimeter Probe along the power contact.
D. At the display harness connector, insert one 7X-1710 Multimeter Probe along the return contact.
E. Observe the voltage measurement while wiggling the connectors and wires.
Voltage is:
≥ 21.5 VDC
< 24.8 VDC
OK - Voltage is correct, the display module has failed.
Repair: Replace the display module.
STOP.
Not OK - Voltage is < 21.5 VDC.
Repair: Check the power circuit fuse or circuit breaker.
OK - Fuse is OK or circuit breaker is not tripped.
Go to Step 4.
NOT OK - Fuse is blown or circuit breaker is tripped.
Repair: Replace the fuse or reset the circuit breaker.
STOP.
4. Check The Power Circuit For An Open
A. Harness remains disconnected from the display.
B. Disconnect the power wire from the ECM.
C. Insert one 7X-1710 Multimeter Probe at each end of the power wire.
D. Observe the resistance measurement.
Wire has continuity.
OK - Wire has continuity.
Go to Step 5.
Not OK - Wire is open.
Repair: Repair or replace the harness.
STOP.
5. Check The Ground Circuit
A. Harness remains disconnected from the display.
B. Insert one 7X-1710 Multimeter Probe at the display harness connector return contact.
C. Insert one 7X-1710 Multimeter Probe at frame ground.
D. Observe the resistance measurement.
Wire has continuity.
OK - Wire has continuity.
Go to Step 6.
Not OK - Wire is open.
Repair: Repair or replace the harness.
STOP.
6. Check The System Voltage At The ECM
A. Turn Start switch and Disconnect switch ON.
B. At the display harness connector, insert one 7X-1710 Multimeter Probe along the power contact.
C. At the display harness connector, insert one 7X-1710 Multimeter Probe along the return contact.
D. Observe the voltage measurement while wiggling the connectors and wires.
Voltage is:
≥ 21.5 VDC
< 24.8 VDC
OK - Voltage is correct, the ECM may have failed.
Contact your technical communicator(2).
Not OK - Voltage is < 21.5 VDC.
Repair: Repair or replace the harness.
STOP.
(1) See Testing and Adjusting, "Electrical Connector - Inspect".
(2) If ECM replacement is required, see Testing and Adjusting, "Module - Replace".
Table 1
Troubleshooting Test Steps Values Results
1. Identify Any Active Code Associated With The Circuit Voltage
A. Connect Cat® Electronic Technician (Cat ET) Service Tool.
B. Check for codes.
No codes present.
OK - No codes present.
Go to Step 2.
Not OK - Code is present.
Go to the test procedure for that code.
STOP.
2. Check Connections And Harness
A. Inspect the circuit harness connectors(1).
B. Inspect the harness.
A. Connectors are:
* Clean
* Secure
* In good condition
B. Harness is not:
*Kinked
*Chafed
OK - Connections and harness are good.
Go to Step 3.
Not OK - A connection problem exists.
Repair:
A. Clean and secure connectors(1).
B. Verify that the problem is corrected.
STOP.
3. Check The System Voltage At The Display Module
A. Turn Start switch and Disconnect switch ON.
B. Disconnect the harness from the display.
C. At the display harness connector, insert one 7X-1710 Multimeter Probe along the power contact.
D. At the display harness connector, insert one 7X-1710 Multimeter Probe along the return contact.
E. Observe the voltage measurement while wiggling the connectors and wires.
Voltage is:
≥ 21.5 VDC
< 24.8 VDC
OK - Voltage is correct, the display module has failed.
Repair: Replace the display module.
STOP.
Not OK - Voltage is < 21.5 VDC.
Repair: Check the power circuit fuse or circuit breaker.
OK - Fuse is OK or circuit breaker is not tripped.
Go to Step 4.
NOT OK - Fuse is blown or circuit breaker is tripped.
Repair: Replace the fuse or reset the circuit breaker.
STOP.
4. Check The Power Circuit For An Open
A. Harness remains disconnected from the display.
B. Disconnect the power wire from the ECM.
C. Insert one 7X-1710 Multimeter Probe at each end of the power wire.
D. Observe the resistance measurement.
Wire has continuity.
OK - Wire has continuity.
Go to Step 5.
Not OK - Wire is open.
Repair: Repair or replace the harness.
STOP.
5. Check The Ground Circuit
A. Harness remains disconnected from the display.
B. Insert one 7X-1710 Multimeter Probe at the display harness connector return contact.
C. Insert one 7X-1710 Multimeter Probe at frame ground.
D. Observe the resistance measurement.
Wire has continuity.
OK - Wire has continuity.
Go to Step 6.
Not OK - Wire is open.
Repair: Repair or replace the harness.
STOP.
6. Check The System Voltage At The ECM
A. Turn Start switch and Disconnect switch ON.
B. At the display harness connector, insert one 7X-1710 Multimeter Probe along the power contact.
C. At the display harness connector, insert one 7X-1710 Multimeter Probe along the return contact.
D. Observe the voltage measurement while wiggling the connectors and wires.
Voltage is:
≥ 21.5 VDC
< 24.8 VDC
OK - Voltage is correct, the ECM may have failed.
Contact your technical communicator(2).
Not OK - Voltage is < 21.5 VDC.
Repair: Repair or replace the harness.
STOP.
(1) See Testing and Adjusting, "Electrical Connector - Inspect".
(2) If ECM replacement is required, see Testing and Adjusting, "Module - Replace".
Cat SIS web machinery list:
Parts ball Caterpillar catalog:
2H3814
BALL BEARING
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D F...
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D F...
4S8546
BALL BEARING
589, 641B, 650B, 777, 785, 789, 814, 824C, 826C, 834B, 936, 950, 950B, 950B/950E, 955K, 955L, 966C, 980C, 983B, 988B, D11N, D400, D44B, D5, D550B, D5B, D5H, D5HTSK II, D8L, D9L, D9N, G936
589, 641B, 650B, 777, 785, 789, 814, 824C, 826C, 834B, 936, 950, 950B, 950B/950E, 955K, 955L, 966C, 980C, 983B, 988B, D11N, D400, D44B, D5, D550B, D5B, D5H, D5HTSK II, D8L, D9L, D9N, G936
8M6418
BALL BEARING
613, 950, 955H, 983, D4H, D5H, D7F
613, 950, 955H, 983, D4H, D5H, D7F
1B4102
BALL BEARING
55, 57, 58, 941, 951B, 955C, 955H, 955K, 955L, D4D, D4E, D4E SR
55, 57, 58, 941, 951B, 955C, 955H, 955K, 955L, D4D, D4E, D4E SR
9M1997
BALL BEARING
14E, 528, 54, 55, 57, 572G, 58, 594H, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 977K, AD55B, AD60, D10N, D10R, D4H, D4HTSK II, D5B...
14E, 528, 54, 55, 57, 572G, 58, 594H, 769C, 772B, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 977K, AD55B, AD60, D10N, D10R, D4H, D4HTSK II, D5B...
9M2004
BALL BEARING
14E, 572G, 621, 621B, 621E, 621F, 621R, 623, 623B, 623E, 627, 627B, 627E, 631C, 631E, 633C, 633D, 637D, 637E, 641B, 650B, 651E, 657B, 657E, 657G, 769C, 773B, 777, 777B, 977K, D6C, D6D, D6E, D6G, D7G
14E, 572G, 621, 621B, 621E, 621F, 621R, 623, 623B, 623E, 627, 627B, 627E, 631C, 631E, 633C, 633D, 637D, 637E, 641B, 650B, 651E, 657B, 657E, 657G, 769C, 773B, 777, 777B, 977K, D6C, D6D, D6E, D6G, D7G
5S4442
BALL BEARING
621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 631E, 631G, 633C, 633D, 633E II, 637D, 637E, 637G,...
621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631C, 631E, 631G, 633C, 633D, 633E II, 637D, 637E, 637G,...
8E7898
BALL BEARING
785, 789, 793, 990, 990 II, 992C, 992D, 992G, 994, D10, D11N, D11R
785, 789, 793, 990, 990 II, 992C, 992D, 992G, 994, D10, D11N, D11R
6V3205
BALL BEARING
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ
1688452
BALL BEARING
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325 L, 325B, 325B L, 325C, 325C FM, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, OEMS
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 324D, 324D L, 324D LN, 325 L, 325B, 325B L, 325C, 325C FM, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, OEMS
8E6414
BALL BEARING
325, 325 L, 325 LN, OEMS
325, 325 L, 325 LN, OEMS
1688453
BALL BEARING
330B, 330B L, OEMS
330B, 330B L, OEMS
2N6642
BALL
7231
7231
5B9018
BALL JOINT
824C, 826C, 955C, 977D, 980C, CW-14, D315, D398, D399, PS-150B, PS-150C, PS-200B
824C, 826C, 955C, 977D, 980C, CW-14, D315, D398, D399, PS-150B, PS-150C, PS-200B
3N1910
BALL BEARING
3208
3208
9L2685
BALL JOINT
140, 1673, 1673B, 1673C, 1674, 1676, 1693, 225, 245, 613, 613B, 613C, 613C II, 633D, 815B, 824C, 826C, 834B, 836, 901C, 902C, 903C, 916, 926, 930R, 931B, 936, 936F, 950B, 966C, 966D, 966R, 980C, 980F,...
140, 1673, 1673B, 1673C, 1674, 1676, 1693, 225, 245, 613, 613B, 613C, 613C II, 633D, 815B, 824C, 826C, 834B, 836, 901C, 902C, 903C, 916, 926, 930R, 931B, 936, 936F, 950B, 966C, 966D, 966R, 980C, 980F,...
2H6410
BALL
D250B, D25C, D300B, D30C, D337F, D342, D342C, D343, D350C, D353C, D35C, D35HP, D364, D375D, D400, D40D
D250B, D25C, D300B, D30C, D337F, D342, D342C, D343, D350C, D353C, D35C, D35HP, D364, D375D, D400, D40D
1P0231
BALL
1673C, 1674, 1676, 3304, 3306, 631C, 941, 943, 950, 966C, D6C, D7F, D8K
1673C, 1674, 1676, 3304, 3306, 631C, 941, 943, 950, 966C, D6C, D7F, D8K
6F8785
BALL
D326F, D337, D337F, D342, D353C, D364, D375D, D397D, D9E
D326F, D337, D337F, D342, D353C, D364, D375D, D397D, D9E
7F3966
BALL
D364
D364
5B9133
BALL
D315, D326F, D337, D343, D375D, D397D
D315, D326F, D337, D343, D375D, D397D
5B1088
BALL
D315, D342
D315, D342
0589318
BALL
D379B
D379B
5B9419
BALL
120B, 12E, 140B, 14E, 518, 518C, 528, 528B, 530B, 651, 814, 834, 910, 920, 930, 950, 966C, 980B, 992, D315, D337, D342C, D343, D397D, D398, D8H, FB518, G342C
120B, 12E, 140B, 14E, 518, 518C, 528, 528B, 530B, 651, 814, 834, 910, 920, 930, 950, 966C, 980B, 992, D315, D337, D342C, D343, D397D, D398, D8H, FB518, G342C