2298597 BALL BEARING Caterpillar parts
836, 988B, 988F, 988F II, 992C
Rating:
Alternative (cross code) number:
CA2298597
229-8597
2298597
CA2298597
229-8597
2298597
Weight: 2 pounds 0 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compatible equipment models: 2298597:
Number on catalog scheme:
17
For full view, you need register
Information:
Oil Change Interval
Considerations for the oil change interval include the type of fuel and the engine application. An established S O S oil analysis program enables used oil to be evaluated. The evaluation can be used to determine if this oil change interval is suitable for your specific engine.Engines That Use Bio-Gas
The oil change interval is determined by the results of oil analysis. Change the lubrication oil when oil analysis determines that the oil has reached the condemning limit. Also, change the engine oil filters.Change the Engine Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Ensure that the engine is stopped before performing this procedure. Attach a DO NOT OPERATE tag to the starting controls.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.Note: Drain the oil into a suitable container. Dispose of fluids according to local regulations.
Illustration 1 g00789667
(1) Drain valve
Open drain valve (1) in order to drain used oil. After the oil has drained, close drain valve (1) .Note: If a suction device is used in order to remove the oil from the oil pan, ensure that the suction device is clean. This will prevent dirt from entering the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
Clean the oil suction screen.Note: Approximately 1 L (1 qt) of oil will remain in the housing after the sump has been completely drained. This oil will pour out of the housing when the cover for the oil suction screen is removed. Prepare to catch the oil in a suitable container. Clean up any spilled oil with rags. DO NOT use absorbent particles to clean up the oil.
Illustration 2 g00789729
(2) Screen assembly
Loosen the bolts of the cover for the oil suction screen. Remove the cover and the gasket. Discard the old gasket. Slide screen assembly (2) from the tube.
Wash the screen assembly in clean nonflammable solvent. Allow the screen assembly to dry before installation.
Install the screen assembly. Install a new gasket. Install the cover.
Change the engine oil filters. Refer to this Operation and Maintenance Manual, "Engine Oil Filter - Change" topic (Maintenance Section).
Only use oils that are recommended by Caterpillar. For the proper oil to use, refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section).
Engine damage can occur if the crankcase is filled above the "FULL" mark on the oil level gauge (dipstick).An overfull crankcase can cause the crankshaft to dip into the oil. This
Considerations for the oil change interval include the type of fuel and the engine application. An established S O S oil analysis program enables used oil to be evaluated. The evaluation can be used to determine if this oil change interval is suitable for your specific engine.Engines That Use Bio-Gas
The oil change interval is determined by the results of oil analysis. Change the lubrication oil when oil analysis determines that the oil has reached the condemning limit. Also, change the engine oil filters.Change the Engine Oil
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Ensure that the engine is stopped before performing this procedure. Attach a DO NOT OPERATE tag to the starting controls.
Do not drain the oil when the engine is cold. As the oil cools, suspended waste particles settle on the bottom of the oil pan. The waste particles are not removed when the cold oil is drained. Drain the crankcase with the oil warm. This draining method allows the waste particles that are suspended in the oil to be drained properly.Failure to follow this recommended procedure will allow the waste particles to be recirculated through the engine lubrication system with the new oil.
After the engine has been operated at normal operating temperature, STOP the engine.Note: Drain the oil into a suitable container. Dispose of fluids according to local regulations.
Illustration 1 g00789667
(1) Drain valve
Open drain valve (1) in order to drain used oil. After the oil has drained, close drain valve (1) .Note: If a suction device is used in order to remove the oil from the oil pan, ensure that the suction device is clean. This will prevent dirt from entering the oil pan. Be careful not to strike the engine oil suction tubes or the piston cooling jets.
Clean the oil suction screen.Note: Approximately 1 L (1 qt) of oil will remain in the housing after the sump has been completely drained. This oil will pour out of the housing when the cover for the oil suction screen is removed. Prepare to catch the oil in a suitable container. Clean up any spilled oil with rags. DO NOT use absorbent particles to clean up the oil.
Illustration 2 g00789729
(2) Screen assembly
Loosen the bolts of the cover for the oil suction screen. Remove the cover and the gasket. Discard the old gasket. Slide screen assembly (2) from the tube.
Wash the screen assembly in clean nonflammable solvent. Allow the screen assembly to dry before installation.
Install the screen assembly. Install a new gasket. Install the cover.
Change the engine oil filters. Refer to this Operation and Maintenance Manual, "Engine Oil Filter - Change" topic (Maintenance Section).
Only use oils that are recommended by Caterpillar. For the proper oil to use, refer to this Operation and Maintenance Manual, "Refill Capacities and Recommendations" topic (Maintenance Section).
Engine damage can occur if the crankcase is filled above the "FULL" mark on the oil level gauge (dipstick).An overfull crankcase can cause the crankshaft to dip into the oil. This
Caterpillar parts catalog:
Parts ball Caterpillar catalog:
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992G, 992K, 993K, 994, 994D, 994F, 994H, D11R, D11T
5P1669
BALL BEARING
797, 797B, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H, D10, D11N, D11R, D11T
797, 797B, 844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H, D10, D11N, D11R, D11T
1103970
BALL
988G
988G
3098477
BALL BEARING
773F, 775F, 834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
773F, 775F, 834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K
525, 525B, 525C, 535B, 535C, 545, 545C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966F, 966F II, 966G, 966G II, 966H, 966K, 970F, 972G, 972G II, 972H, 972K, R1300, R1300G
1300960
BALL BEARING
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 836G, 836H, 950G, 962G, 980G, 980G II, 980H
824G, 824G II, 824H, 825G, 825G II, 825H, 826G, 826G II, 826H, 836G, 836H, 950G, 962G, 980G, 980G II, 980H
814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, R1300, R1300G, R1700 II, R1700G, R2900, R2900G, R3000H
1052036
BALL BEARING
993K, 994, 994D, 994F, 994H
993K, 994, 994D, 994F, 994H
785, 789, 793, 990, 990 II, 992C, 992D, 992G, 994, D10, D11N, D11R
6Y3424
BALL BEARING
785, 992C, 994
785, 992C, 994
5P4904
BALL BEARING
990, 990 II, 992C, 992D, 992G, 994, D10, D11N, D11R
990, 990 II, 992C, 992D, 992G, 994, D10, D11N, D11R
5P6728
BALL BEARING
785, 789, 992C, D10, D11N
785, 789, 992C, D10, D11N