5P7602 BALL BEARING Caterpillar parts
14G, 14H, 14H NA, 16G, 16H, 16H NA
Rating:
Alternative (cross code) number:
CA5P7602
5P-7602
5P7602
CA5P7602
5P-7602
5P7602
Weight: 1 pounds 0 kg.
MOTOR GRADER,
Number on catalog scheme:
31
For full view, you need register
Information:
Machine Preparation
Move the machine to a smooth horizontal location. Move away from working machines and personnel. Lower the work tools to the ground.
Allow only one operator on the machine. Keep all personnel away from the machine or in the view of the operator.
Engage the parking brake.
Illustration 1 g03731880
Place the steering frame lock in the LOCKED position.Reference: For information about preparing a machine for troubleshooting, refer to the Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.Hydraulic Fan Speed (Testing and Adjusting)
Place the transmission in the NEUTRAL position. Engage the parking brake. Connect Caterpillar Electronic Technician (ET) to the diagnostic connector. The diagnostic connector is located to the left and behind the operator seat.
Illustration 2 g02427958
Start ET. When ET initializes, select the engine ECM from the choices that are available. Refer to Illustration 2.
Illustration 3 g02428248
Illustration 4 g02428436
Check all fault codes under the engine ECM. Ensure that no faults are present in the fan drive system. Ensure that no faults are present with the hydraulic oil temperature sensor, engine coolant temperature sensor and inlet manifold temperature sensor. If no faults are present, ensure that economy mode is “disabled” in the transmission or Power Train ECM configuration. Begin the calibration. Select "Service > Calibrations > Engine Cooling Fan Calibration". Refer to Illustration 3 and Illustration 4.
Illustration 5 g02428259
The screen that is shown in Illustration 5 will appear. Follow the instructions on the screen. Click on "OK".
Illustration 6 g02428276
The "Calibrations" screen will appear. Select both check boxes. Click on "Begin".
Illustration 7 g02428376
Ensure that the parking brake is set. Run the engine at high idle. Click on "Next" in the lower left corner of the screen.
Continue running the machine at high idle. Use the photo tach to measure the fan speed. Adjust the current for the fan solenoid by using the arrows at the bottom of the screen. Increasing the current will decrease the fan speed. Decreasing the current will increase the fan speed. Adjust the current until the minimum fan speed shown in Table 1 or Table 2 is reached.Note: If the machine is equipped with the variable pitch fan, set the fan
Move the machine to a smooth horizontal location. Move away from working machines and personnel. Lower the work tools to the ground.
Allow only one operator on the machine. Keep all personnel away from the machine or in the view of the operator.
Engage the parking brake.
Illustration 1 g03731880
Place the steering frame lock in the LOCKED position.Reference: For information about preparing a machine for troubleshooting, refer to the Testing and Adjusting, "Machine Preparation for Troubleshooting" for the machine that is being serviced.Hydraulic Fan Speed (Testing and Adjusting)
Place the transmission in the NEUTRAL position. Engage the parking brake. Connect Caterpillar Electronic Technician (ET) to the diagnostic connector. The diagnostic connector is located to the left and behind the operator seat.
Illustration 2 g02427958
Start ET. When ET initializes, select the engine ECM from the choices that are available. Refer to Illustration 2.
Illustration 3 g02428248
Illustration 4 g02428436
Check all fault codes under the engine ECM. Ensure that no faults are present in the fan drive system. Ensure that no faults are present with the hydraulic oil temperature sensor, engine coolant temperature sensor and inlet manifold temperature sensor. If no faults are present, ensure that economy mode is “disabled” in the transmission or Power Train ECM configuration. Begin the calibration. Select "Service > Calibrations > Engine Cooling Fan Calibration". Refer to Illustration 3 and Illustration 4.
Illustration 5 g02428259
The screen that is shown in Illustration 5 will appear. Follow the instructions on the screen. Click on "OK".
Illustration 6 g02428276
The "Calibrations" screen will appear. Select both check boxes. Click on "Begin".
Illustration 7 g02428376
Ensure that the parking brake is set. Run the engine at high idle. Click on "Next" in the lower left corner of the screen.
Continue running the machine at high idle. Use the photo tach to measure the fan speed. Adjust the current for the fan solenoid by using the arrows at the bottom of the screen. Increasing the current will decrease the fan speed. Decreasing the current will increase the fan speed. Adjust the current until the minimum fan speed shown in Table 1 or Table 2 is reached.Note: If the machine is equipped with the variable pitch fan, set the fan
Caterpillar parts catalog:
Parts ball Caterpillar catalog:
120B, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3,...
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 416B, 416C, 416D, 420D, 424D, 426, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 4...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, 163H,...
120G, 12G, 130G, 140G, 14G, 153, 160G, 163, 16G, 183B, 2384C, 2484C, 30/30, 311, 311B, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, ...
12E, 12G, 16, 16G, 215, 215B, 215D, 219D, 225, 225D, 229, 229D, 231D, 235, 235B, 235C, 235D, 245, 245B, 245D, 30/30, 307B, 312, 312D, 312D L, 314D CR, 314D LCR, 315, 315D L, 317, 3192, 319D, 319D L, 3...
12E, 140B, 140H, 143H, 14H, 14M, 16, 160H, 163H, 1693, 16G, 16H, 16M, 245, 24M, 301.5, 301.6C, 302.5, 302.5C, 303, 303.5, 307C, 307D, 308C, 308D, 308E, 3114, 3116, 3176, 3176B, 3176C, 3196, 3304, 3306...
12E, 153, 16, 163, 16G, 172, 173B, 183B, 191, 245, 3406, 3406B, 3408, 3408B, 3408C, 3412, 375, 561B, 572G, 578, 583H, 583K, 589, 594, 594H, 611, 613C, 613C II, 613G, 615, 615C, 621, 621B, 621E, 623, 6...
120G, 12E, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 215, 215B, 215C, 215D, 225, 231D, 235, 235B, 235C, 245, 325, 325 L, 325 LN, 3512C, 375, 375 L, 561B, 561C, 561D, E240C, G3508, G35...
120G, 12G, 130G, 140G, 14G, 14H NA, 160G, 16G, 16H NA, 589, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D8L, D9L, D9R
12F, 12G, 14E, 14G, 16, 16G, 627B, 637D, 844, 844H, 854G, 854K, 933, 939, 990, 990 II, 990H, 992G, 992K, 994F, D10, D10N, D11N, D3C III, D4C III, D5C III, D8L, D9L, D9N, D9R
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA
9U9693
BALL BEARING
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 24H
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 24H
2228288
BALL BEARING
330C, 330C L, 345B, 345B II, 345B II MH, 345B L, W345B II
330C, 330C L, 345B, 345B II, 345B II MH, 345B L, W345B II
330B, 330B L, OEMS
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
120G, 12G, 130G, 140G, 160G
2436690
BALL
24H, 24M
24H, 24M
1361020
BALL BEARING
24H, 24M
24H, 24M
5Y0014
BALL
120G, 140G
120G, 140G
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA