8E0853 BALL JOINT AS Caterpillar parts
AP-650B, AP-800D, CB-434C, CB-434D, CB-534C, CB-534D, CB-535B, CB-564D, CB-634C, CB-634D, CD-54, CP-433E, CP-533E, CS-423E, CS-433E, CS-533E, D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8...
Rating:
Alternative (cross code) number:
CA8E0853
8E-0853
8E0853
CA8E0853
8E-0853
8E0853
Weight: 0.010 pounds 0 kg.
Information:
PIVOT ANGLE
30
ROD LENGTH
14.27
mm
BODY PIVOT LENGTH
32.5
STUD PIVLOT LG
20.5
BODY THREAD
.25-28
BODY THREAD LENGTH
14
STUD THD
.25-28
ASPHALT PAVER, VIBRATORY COMPACTOR,
Compatible equipment models: 8E0853:
Number on catalog scheme:
2
For full view, you need register
Information:
Deck/Work Over Mode (Low Idle Power Shift)
The transmission will shift according to the operator input by using the up arrow and the down arrow. The transmission will operate as a low idle power shift transmission and the transmission will shift at an engine speed less than or equal to 850 rpm.Quick to NEUTRAL
Note: This function is applicable only in the pump application.When the quick to neutral switch is activated, the transmission quickly downshifts to the NEUTRAL position. When the quick to neutral switch is deactivated, the transmission will remain in the NEUTRAL position until the transmission shift control is placed in the NEUTRAL position. Then, the transmission can be shifted to the desired gear.Switching Drop Box Modes
Note: The following conditions must be met in order to switch drop box modes.
The engine must remain running at LOW IDLE.
Transmission gear is in NEUTRAL.
The transmission has no output speed. Four Wheel Drive (4WD) Switching Modes
Procedure for Engaging 4WD
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Press the brakes and maintain the engine at LOW IDLE.
Place the transmission in the lowest possible gear. The TH31 should be placed in the 1F gear. The TH35 should be placed in the 2F gear.
Toggle the 4WD/2WD switch to the 4WD position.
Drive the vehicle in the forward direction for one half the length of the vehicle. Engine speed will be limited until the shift is complete and the vehicle stops moving.
Apply the brakes and stop the vehicle.
Place the transmission in neutral.
Check the keypad shifter for 4WD engagement. Note: If the transmission is in 4WD then the procedure is complete. If the transmission control display is still blinking, repeat the procedure and direction.Procedure for Disengaging 4WD
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Press the brakes and maintain the engine at low idle.
Place the transmission in the lowest possible gear. The TH31-E61 should be placed in the 1F gear. The TH35-E81 should be placed in the 2F gear.
Toggle the 4WD/2WD switch to the 2WD position.
Drive the vehicle in the forward direction for one half the length of the vehicle. Engine speed will be limited until the shift is complete and the vehicle stops moving.
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Check the keypad shifter for 2WD engagement. Note: If the transmission is in 2WD then the procedure is complete. If the transmission control display is still blinking, repeat the procedure and direction.PTO Pump Displacement Control
This function on the TH31-E61 and TH35-E81 transmissions outputs a variable electric current. This current can be used to power displacement control solenoids on variable displacement hydraulic pumps or other solenoids or equipment requiring a variable input current. The transmission supports two separate variable output currents.The ECM uses proportional drivers to output a current from 0 amp – 2 amp which are controlled using two switches for each current driver, an on/off switch, and a current increment/decrement switch. When the on/off switch is moved to the ON position, the output
The transmission will shift according to the operator input by using the up arrow and the down arrow. The transmission will operate as a low idle power shift transmission and the transmission will shift at an engine speed less than or equal to 850 rpm.Quick to NEUTRAL
Note: This function is applicable only in the pump application.When the quick to neutral switch is activated, the transmission quickly downshifts to the NEUTRAL position. When the quick to neutral switch is deactivated, the transmission will remain in the NEUTRAL position until the transmission shift control is placed in the NEUTRAL position. Then, the transmission can be shifted to the desired gear.Switching Drop Box Modes
Note: The following conditions must be met in order to switch drop box modes.
The engine must remain running at LOW IDLE.
Transmission gear is in NEUTRAL.
The transmission has no output speed. Four Wheel Drive (4WD) Switching Modes
Procedure for Engaging 4WD
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Press the brakes and maintain the engine at LOW IDLE.
Place the transmission in the lowest possible gear. The TH31 should be placed in the 1F gear. The TH35 should be placed in the 2F gear.
Toggle the 4WD/2WD switch to the 4WD position.
Drive the vehicle in the forward direction for one half the length of the vehicle. Engine speed will be limited until the shift is complete and the vehicle stops moving.
Apply the brakes and stop the vehicle.
Place the transmission in neutral.
Check the keypad shifter for 4WD engagement. Note: If the transmission is in 4WD then the procedure is complete. If the transmission control display is still blinking, repeat the procedure and direction.Procedure for Disengaging 4WD
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Press the brakes and maintain the engine at low idle.
Place the transmission in the lowest possible gear. The TH31-E61 should be placed in the 1F gear. The TH35-E81 should be placed in the 2F gear.
Toggle the 4WD/2WD switch to the 2WD position.
Drive the vehicle in the forward direction for one half the length of the vehicle. Engine speed will be limited until the shift is complete and the vehicle stops moving.
Apply the brakes and come to a complete stop.
Place the transmission in neutral.
Check the keypad shifter for 2WD engagement. Note: If the transmission is in 2WD then the procedure is complete. If the transmission control display is still blinking, repeat the procedure and direction.PTO Pump Displacement Control
This function on the TH31-E61 and TH35-E81 transmissions outputs a variable electric current. This current can be used to power displacement control solenoids on variable displacement hydraulic pumps or other solenoids or equipment requiring a variable input current. The transmission supports two separate variable output currents.The ECM uses proportional drivers to output a current from 0 amp – 2 amp which are controlled using two switches for each current driver, an on/off switch, and a current increment/decrement switch. When the on/off switch is moved to the ON position, the output
Cat SIS web machinery list:
Parts ball Caterpillar catalog:
24H, 24M, 517, 527, 561M, 561N, 589, 613C, 613C II, 613G, 651E, 657E, 657G, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 824C, 82...
572R, 572R II, 578, 583R, 583T, 587R, 587T, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 980C, 980F, 980F II, 980...
589, 824C, 824G, 824G II, 824H, 824K, 825G, 825G II, 825H, 825K, 826C, 826G, 826G II, 826H, 826K, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 980F, 980F II, 980G, 980G II, 980H, 980K, 980K HLG, 980...
589, 834G, 834H, 834K, 836G, 836H, 836K, 988G, 988H, 988K, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R, D9T
117, 118, 119, 127, 128, 129, 25, 30, 572R II, 578, 587R, 589, 619, 651, 657, 657B, 666, 769, 772, 834, 966F, 966G, 966G II, 972G, 972G II, 972H, 972K, 972M, 980F, 980G, 980H, 980K, 980M, 992, D10N, D...
578, 583R, 589, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 826C, 834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 844, 844H, 844K, 854G, 854K, 902, 906, 906H, 906H2, 907H...
578, 583R, 587R, 587T, D8N, D8R, PL87
572G, 578, 627, 627B, 977H, 988, D5, D5B, D6C, D6D, D6H, D6H XR, D7G, D7H, D8N
14E, 527, 578, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 950, 966C, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D7E, D7E LGP, D7G, D7H, D7R, D8N, D8R
12F, 12G, 14E, 14G, 16, 16G, 627B, 637D, 844, 844H, 854G, 854K, 933, 939, 990, 990 II, 990H, 992G, 992K, 994F, D10, D10N, D11N, D3C III, D4C III, D5C III, D8L, D9L, D9N, D9R
583T, 587R, 587T, 621G, 627G, 631G, 637G, 963D, 973C, D7E, D7E LGP, D8R, D8R II, D8T, HA871, PL83, PL87, TK371, TK381
16, 583T, 651, 657, 666, 768B, 769, 772, 773, 993K, AP-1055D, AP-600D, AP-655C, AP-655D, BG-2455D, BG-260D, BG600D, BG655D, CW-14, D350E, D350E II, D35HP, D3B, D400, D400E, D400E II, D40D, PF-290B, PF...
6Y2841
BALL BEARING
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
6Y3140
BALL JOINT AS
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
D6H, D6H II, D6H XL, D6H XR, D6R, D6R STD, D7H, D7R XR, D8N, D8R, D9R
517, 527, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II
517, 527, 561M, 561N, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962H, 966C, 966H, 966R, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D5N, D5R LGP, D6M, D6N, D6N L...
814B, 815B, 966D, 966F, 966F II, 970F, D5H, D5H XL, D5HTSK II
814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, D5H, D5HTSK II
931B, 931C, 933, 939, D3C, D3C II, D3C III, D4C III, D5C III
6S7940
BALL JOINT AS
901C, 902C, 903C, 904B, 904H, 931B, 931C, 931C II, 933, 933C, 935B, 939, 939C, D3, D3B, D3C, D3C II, D3C III, D3G, D4C, D4C III, D4G, D5C III, D5G
901C, 902C, 903C, 904B, 904H, 931B, 931C, 931C II, 933, 933C, 935B, 939, 939C, D3, D3B, D3C, D3C II, D3C III, D3G, D4C, D4C III, D4G, D5C III, D5G
613, 950, 955H, 983, D4H, D5H, D7F
517, 518, 518C, 613C, 613C II, 936F, 966C, D250D, D4H XL, D4HTSK II, D4HTSK III
7T8419
BALL BEARING
902, 906, 908, CP-433E, CP-44, CS-423E, CS-433E, CS-44, D6H, D7H
902, 906, 908, CP-433E, CP-44, CS-423E, CS-433E, CS-44, D6H, D7H
7T8420
BALL BEARING
D6F SR, D6G SR, D6H, D7H
D6F SR, D6G SR, D6H, D7H