7D8245 BALLSTUD Caterpillar parts
120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12F, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA...
Rating:
Alternative (cross code) number:
CA7D8245
7D-8245
7D8245
CA7D8245
7D-8245
7D8245
Weight: 4 pounds 1 kg.
Information:
BALL DIA
69.85
C/L TO SHOULDER
0
MOTOR GRADER, TRACK FELLER BUNCHER,
Compatible equipment models: 7D8245:
MOTOR GRADER
120
120B
120G
120H
120H ES
120H NA
120K
120K 2
120M
120M 2
12E
12F
12G
12H
12H ES
12H NA
12K
12M
12M 2
12M 3
12M 3 AWD
130G
135H
135H NA
140
140B
140G
140H
140H ES
140H NA
140K
140K 2
140M
140M 2
140M 3
140M 3 AWD
143H
14E
160G
160H
160H ES
160H NA
160K
160M
160M 2
160M 3
160M 3 AWD
163H
163H NA
Information:
Illustration 1 g00895497
Schematic of the temperature sensor (transmission oil)
This diagnostic code is associated with the temperature sensor (transmission oil). The FMI 08 means that the ECM has determined that the signal frequency or the signal pulse width is not within the expected range. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
Mechanical devices are loose.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0177 FMI 08 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure. Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact C).
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact C to frame ground. Expected Result:The voltage is 8.Results:
OK - The voltage is 8. Proceed to Test Step 3.
NOT OK - The voltage is not 8. The circuit is open. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT OF THE SENSOR.
Turn the key start switch and the disconnect switch to the OFF position.
At the back of the harness connector for the sensor, remove the 7X-1710 Multimeter Probe from contact C and insert the probe along the signal wire (contact A).
At the back of the harness connector for the sensor, insert the 7X-1710 Multimeter Probe along the ground wire (contact B).
Turn the disconnect switch and the key start switch to the ON position.
Monitor the signal of the sensor with the 146-4080 Digital Multimeter.
Without disconnecting the sensor or the hardware that is associated with the sensor from the machine, take the sensor through
Cat SIS web machinery list:
Parts ballstud Caterpillar catalog:
2G2411
BALLSTUD AS
12G, 130G, 140G
12G, 130G, 140G
4D1476
BALLSTUD
120B, 12E, 12F, 140, 140B, 14E
120B, 12E, 12F, 140, 140B, 14E
2D7838
BALLSTUD
140
140
2D0283
BALLSTUD
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
4H7805
BALLSTUD
120, 120B, 12E, 140, 140B
120, 120B, 12E, 140, 140B
7D0038
BALLSTUD
12F, 14E
12F, 14E
7D8761
BALLSTUD
14E, 16
14E, 16
6D3404
BALLSTUD
12F, 14E
12F, 14E
5D0345
BALLSTUD
12F, 14E
12F, 14E
8D4941
BALLSTUD ASSEM.
12G, 130G, 140G
12G, 130G, 140G
2G6561
BALLSTUD ASSEM.
120G, 12G, 130G
120G, 12G, 130G
9D6451
BALLSTUD ASSEM.
120G, 12G, 130G, FB221
120G, 12G, 130G, FB221
5V5351
BALLSTUD
227
227
5T6502
BALLSTUD
789
789
5T8597
BALLSTUD
785
785
6D1726
BALLSTUD
769
769
2M6345
BALLSTUD
768B, 769, 772, 773
768B, 769, 772, 773
6D6033
BALLSTUD
12F, 14E
12F, 14E
2G2411
BALLSTUD AS
12G, 130G, 140G
12G, 130G, 140G
2G5962
BALLSTUD AS
120G
120G
6J9749
BALLSTUD
7A, 7S, D7G
7A, 7S, D7G
3R3297
BALLSTUD
7A, D7F
7A, D7F