AVSPARE.COM
parts catalog

BARREL ASSEM. 9J3969 - Caterpillar


9J3969 BARREL ASSEM. Caterpillar parts 14G, 225, 245
Rating:
86
Alternative (cross code) number:
CA9J3969
9J-3969
9J3969
Caterpillar 9J3969 BARREL ASSEM.
Weight: 22 pounds 10 kg.

Buy BARREL ASSEM. 9J3969 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR, MOTOR GRADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$470.04
 

09 Feb 2022

US: Florida-Parts-Z
9J2417 - Barrel ASSEM. 9J3969 9J8266 for Caterpillar (CAT)
FIRST PRICE PARTS
$331.83
 

20 Mar 2017

BLQ: BLQ
9J3969 BARREL A
Number on catalog scheme: 1
  For full view, you need register

Compatible equipment models: 9J3969:

EXCAVATOR  225   245  
MOTOR GRADER  14G   Caterpillar

Information:


Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Illustration 1 g01186208
Left side view of engine
(1) Fuel priming pump (if equipped)
Illustration 2 g01326675
Detailed view of the fuel filter and priming pump
(2) Fuel priming pump
(3) Air purge fitting If the fuel system runs out of fuel or if air is introduced into the fuel system, either of the following procedures may be followed. If necessary, fill the fuel tank with clean diesel fuel.Using the Engine to Prime the Fuel System
Turn the ignition switch to the OFF position.
Unlock the fuel priming pump (if equipped) by turning the cap counterclockwise.
Purging air from the fuel system requires the air purge fitting to be opened. Turn the air purge fitting counterclockwise by three full turns. Do not remove the fitting.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Crank the engine for 30 seconds. Use a suitable container to catch the fuel while you crank the engine. Allow the starting motor to cool for two minutes. Note: Most of the air should be purged from the system after four or five cranking cycles.
Repeat Step 4 until the engine starts and runs. If the engine runs rough, continue to operate the engine at low idle until the engine runs smoothly.
Observe the air purge fitting. When a small drop of fuel appears at the threads of the air purge fitting, close the air purge fitting. After the air purge fitting is closed, tighten the air purge fitting. Refer to Specifications, SENR3130 for the correct torque. Note: Failure to tighten all fittings could result in serious fuel leaks.
After the engine has operated smoothly for 30 seconds, turn the priming valve to the LOCK position. Note: The

Caterpillar parts catalog:

Caterpillar parts catalog
14G MOTOR GRADER 96U01098-04297 (MACHINE) POWERED BY 3306 ENGINE
16G MOTOR GRADER 93U00001-01178 (MACHINE)
14G MOTOR GRADER 96U00001-01097 (MACHINE)
245 EXCAVATOR 95V00001-00470 (MACHINE)
225 EXCAVATOR 51U00001-00589 (MACHINE)
225 EXCAVATOR 51U00590-02033 (MACHINE)
245 EXCAVATOR 95V00001-00470 (MACHINE)
225 EXCAVATOR 76U00694-01199 (MACHINE) POWERED BY 3304 ENGINE
225 EXCAVATOR 51U00001-00589 (MACHINE)
225 EXCAVATOR 51U00590-02033 (MACHINE)
225 EXCAVATOR 76U00001-00693 (MACHINE)


Parts barrel Caterpillar catalog:

9T3370 BARREL-CYLINDER
1090, 1190, 1190T, 1290T, 1390, 215B, 225, 2290, 231D, 2390, 2391, 2491, 2590, 322B L, 322C, 322C FM, 324D FM, 324D FM LL, 325B L, 325C FM, 325D FM, 325D FM LL, 330B L, 330C FM, 330C L, 330D FM, 330D ...
9J8667 BARREL ASSEM.
235, 245, 245D, 953, 963, 963B, 973, 992C, 992D, 992G, 994, 994D, 994F
9J2417 BARREL ASSEM.
14G, 16G, 215, 225, 227, 235D, 245, 245B, 245D, 943, 990, 990 II
9T8448 BARREL
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 24H, 24M, 5230, 5230B, 789B, 789C, 789D, 793, 793B, 793C, D8N, D8R, D8R II, D9R
3824818 BARREL AS
308E, 308E CR, 308E SR
3535820 BARREL AS-DRIVEN
311F LRR, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L
3535819 BARREL AS-DRIVE
311F LRR, 312E, 312E L, 314E CR, 314E LCR, 316E L, 318E L
2934368 BARREL
M313D, M315D 2
1570394 BARREL
M318D MH, M322D MH
9J2417 BARREL ASSEM.
14G, 16G, 215, 225, 227, 235D, 245, 245B, 245D, 943, 990, 990 II
9J8667 BARREL ASSEM.
235, 245, 245D, 953, 963, 963B, 973, 992C, 992D, 992G, 994, 994D, 994F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.