1365017 BASE AS-FUEL FILTER Caterpillar parts
3406E, 3456, 385C, 735, 740, C-15, C-16, C-18, C11, C13, C15, C15 I6, C16, C18, C18 I6, CX31-C15I, CX35-P800, D350E II, D400E II, D8R II, PM3456, TH35-C15I, TH35-C15T
Rating:
Alternative (cross code) number:
CA1365017
136-5017
1365017
CA1365017
136-5017
1365017
Weight: 2 pounds 1 kg.
ARTICULATED TRUCK, TRUCK ENGINE,
Number on catalog scheme:
1
For full view, you need register
Information:
3208 Engines;
225 Excavators;
613, 613B TractorsWhen a new crankshaft or a new short block assembly is installed in an earlier 3208 Engine that had a crankshaft with six counterweights, it is possible that oil will leak from between the flywheel and crankshaft flange. The early 3208 Engines that had crankshafts with six counterweights had eight bolt holes in the flywheel and in the crankshaft flange. The crankshafts and short block assemblies that are used for parts service on these earlier engines have ten bolt holes in the crankshaft flange. When the flywheel with eight bolt holes is assembled to the crankshaft with ten bolt holes, oil will go through the two extra holes in the crankshaft flange and leak out between the flywheel and the crankshaft flange. Later flywheels all have ten bolt holes.
Either of two procedures that follow can be used to prevent this type of oil leakage. The first procedure can be done faster but if a replacement crankshaft or short block is installed at a later date, it will be necessary to do the procedure again. For a permanent modification, use "Procedure 2".
Procedure 1
Two A2291 Screws or two screws with no heads are needed. The screws must not be more than .62" (15.7 mm) long and must have 7/16" - 20 thread. Put 9S3263 Thread Lock Compound on the threads and install the screws in the extra holes of the crankshaft flange. See Illustration 1.
Illustration 1. Screw installed in bolt hole.
Be sure the screws are installed in the bolt holes so both ends of the screws are below the inner and outer surface of the flange. If the screws are installed too far into the bolt hole, the ends of the screws can hit the cylinder block and cause damage to the engine.
Procedure 2
Remove the flywheel and machine two .469" (11.91 mm) holes as shown in Illustration 2. Machine a .030" (0.76 mm) X 45° chamfer at the ends of the two holes toward the crankshaft.
Install the flywheel to the crankshaft with ten bolts. Put 8H5137 Sealing Compound on the threads of the bolts.
Illustration 2. Bolt holes in rear face of flywheel.
225 Excavators;
613, 613B TractorsWhen a new crankshaft or a new short block assembly is installed in an earlier 3208 Engine that had a crankshaft with six counterweights, it is possible that oil will leak from between the flywheel and crankshaft flange. The early 3208 Engines that had crankshafts with six counterweights had eight bolt holes in the flywheel and in the crankshaft flange. The crankshafts and short block assemblies that are used for parts service on these earlier engines have ten bolt holes in the crankshaft flange. When the flywheel with eight bolt holes is assembled to the crankshaft with ten bolt holes, oil will go through the two extra holes in the crankshaft flange and leak out between the flywheel and the crankshaft flange. Later flywheels all have ten bolt holes.
Either of two procedures that follow can be used to prevent this type of oil leakage. The first procedure can be done faster but if a replacement crankshaft or short block is installed at a later date, it will be necessary to do the procedure again. For a permanent modification, use "Procedure 2".
Procedure 1
Two A2291 Screws or two screws with no heads are needed. The screws must not be more than .62" (15.7 mm) long and must have 7/16" - 20 thread. Put 9S3263 Thread Lock Compound on the threads and install the screws in the extra holes of the crankshaft flange. See Illustration 1.
Illustration 1. Screw installed in bolt hole.
Be sure the screws are installed in the bolt holes so both ends of the screws are below the inner and outer surface of the flange. If the screws are installed too far into the bolt hole, the ends of the screws can hit the cylinder block and cause damage to the engine.
Procedure 2
Remove the flywheel and machine two .469" (11.91 mm) holes as shown in Illustration 2. Machine a .030" (0.76 mm) X 45° chamfer at the ends of the two holes toward the crankshaft.
Install the flywheel to the crankshaft with ten bolts. Put 8H5137 Sealing Compound on the threads of the bolts.
Illustration 2. Bolt holes in rear face of flywheel.
Cat SIS web machinery list:
Parts base Caterpillar catalog:
3126, 3126B, 3304, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 3412E, 3456, 350, 3516, 5110B, 621, 621B, 623B, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 6...
16G, 16H NA, 245, 245B, 3116, 3126, 3208, 3304, 3306, 3306B, 3306C, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3508B, 3508C, 3512, 3512B, 3512C, 3516B, 3516C, 375,...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 215, 3116, 3304, 3304B, 3306, 3306B, 3406B, 578, 583R, 587R, 615, 615C, 81...
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 725, 730, 966H, 972H, 980C, C11, C13, CX31-C13I, D8N, R1600H, R1700G, RM-300, TH35-C11I, TH35-C13I, W345C MH
16G, 16H NA, 578, 583R, 587R, 631D, 657E, 69D, 769C, 769D, 771C, 771D, 824G, 825G, 826C, 826G, 834B, 836, 980C, 980F, 980G, 988B, 988F, 988F II, AD40, AD45, AE40, AE40 II, D8N, D8R, D8R II
2319483
BASE-FILTER
793F AC, 795F AC, 795F XQ, D5N, D6N, D8R, D8R II
793F AC, 795F AC, 795F XQ, D5N, D6N, D8R, D8R II
611, 613C, 613C II, 615C, 735, 740, 769C, 769D, 770, 771C, 771D, 772, 776, 776C, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793D, 814F, 815B, 815F, 816F, 824G, 825G, 826G, 834B, 836, 966D, ...
8Y5913
BASE-ARMREST
613G, 621G, 621H, 623G, 623H, 627G, 627H, 631G, 637G, 657G, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 924K, 930K, 938K, 950F II, 950G, 950G II, 950H, ...
613G, 621G, 621H, 623G, 623H, 627G, 627H, 631G, 637G, 657G, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 924K, 930K, 938K, 950F II, 950G, 950G II, 950H, ...
1533539
BASE-PEDAL
D350E II, D400E II
D350E II, D400E II
2118611
BASE
735, 740, 773D, D350E II, D400E II
735, 740, 773D, D350E II, D400E II
1591868
BASE
D8R II
D8R II
1471974
BASE
3508, 3508B, 3512, 3512B, 3516, 3516B, PM3508, PM3512, PM3516
3508, 3508B, 3512, 3512B, 3516, 3516B, PM3508, PM3512, PM3516
1291992
BASE-RELAY
3412C, 3508, 3508B, 3512, 3512B, 3516, 3516B, G3508, G3512, G3516, G3516B, G3520B, PP3516
3412C, 3508, 3508B, 3512, 3512B, 3516, 3516B, G3508, G3512, G3516, G3516B, G3520B, PP3516
G3508, G3508B, G3512, G3512B, G3516, G3516B, G3520B, PMG3516
3543206
BASE AS-FUEL TANK
3406C, 3412C
3406C, 3412C
2164424
BASE AS
3406E, 3456
3406E, 3456
2309372
BASE AS
3406E, 3456
3406E, 3456
2309371
BASE AS
3406E, 3456
3406E, 3456