2F7949 BASE-CAP JET Caterpillar parts
Rating:
Alternative (cross code) number:
CA2F7949
2F-7949
2F7949
CA2F7949
2F-7949
2F7949
Weight: 0.01 pounds 0 kg.
Information:
Installation Procedure
Start By:
Ensure that the machine and the work tool is parked on a level surface prior to starting the following procedure. Ensure that the hydraulic lockout that is on the machine is in the LOCKED position.
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Illustration 1 g00851828
Attach a hoist and a suitable lifting device to grapple arm (1) .
Insert grapple arm (1) into the felling head.
Install pivot pin (5) .
Install bolt (6) and the nut into pivot pin (5) .
Illustration 2 g00854323
Typical Example
Install locknut (7) and the washer on pivot pin (5). Note: The nut should already be installed if the left grapple arm cylinder was removed.Tighten the locknut until the clearance between the arm hub (8) and the frame hub (9) is 1 .5 mm (.04 .02 inch).
Remove the lifting device.
Illustration 3 g00851829
Place cylinder (4) into the grapple arm frame.
Install pivot pin (2) .
Install bolt (3) and the nut into pivot pin (2) .
Connect hydraulic hose assembly (8) to the head end of cylinder (4). Connect the hydraulic hose assembly to the rod end of cylinder (4) .
Start By:
Ensure that the machine and the work tool is parked on a level surface prior to starting the following procedure. Ensure that the hydraulic lockout that is on the machine is in the LOCKED position.
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Illustration 1 g00851828
Attach a hoist and a suitable lifting device to grapple arm (1) .
Insert grapple arm (1) into the felling head.
Install pivot pin (5) .
Install bolt (6) and the nut into pivot pin (5) .
Illustration 2 g00854323
Typical Example
Install locknut (7) and the washer on pivot pin (5). Note: The nut should already be installed if the left grapple arm cylinder was removed.Tighten the locknut until the clearance between the arm hub (8) and the frame hub (9) is 1 .5 mm (.04 .02 inch).
Remove the lifting device.
Illustration 3 g00851829
Place cylinder (4) into the grapple arm frame.
Install pivot pin (2) .
Install bolt (3) and the nut into pivot pin (2) .
Connect hydraulic hose assembly (8) to the head end of cylinder (4). Connect the hydraulic hose assembly to the rod end of cylinder (4) .
Parts base Caterpillar catalog:
2F7732
BASE A.
Caterpillar
Caterpillar
2F7731
BASE A.
Caterpillar
Caterpillar
2F5304
BASE A.
Caterpillar
Caterpillar
2F3917
BASE A.
Caterpillar
Caterpillar
2F3883
BASE A.
Caterpillar
Caterpillar
2F3748
BASE A.
Caterpillar
Caterpillar
2F8027
BASE A.
Caterpillar
Caterpillar
2F8503
BASE A.
Caterpillar
Caterpillar
2G6223
BASE-RIM
Caterpillar
Caterpillar
2H1078
BASE
Caterpillar
Caterpillar
2H1080
BASE
Caterpillar
Caterpillar
2H1081
BASE
Caterpillar
Caterpillar