0969534 BEARING Caterpillar parts
E110B, E120B, E200B
Rating:
Alternative (cross code) number:
CA0969534
096-9534
0969534
CA0969534
096-9534
0969534
Weight: 0.15 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
14
For full view, you need register
Information:
In order to achieve the longest life of the components for the snubber, the operation of the snubber should be monitored constantly. The adjustment should be tight enough to avoid damaging contact with the arch or the boom while the grapple arms (tongs) are empty.
Illustration 1 g00956113
Illustration 2 g00956038
View A-AUpper Joint Assembly (1) Bolt. (2) Cap. (3) Shims. (4) Reaction plate. (5) Friction plate.
Illustration 3 g00956037
View B-BLower Joint Assembly (1) Bolt. (2) Cap. (3) Shims. (4) Reaction plate. (5) Friction plate.The amount of drag of the snubber is set with shims (3). In order to increase the drag of the snubber, remove shims. In order to decrease drag of the snubber, add shims.
To adjust the snubber, loosen bolts (1) from cap (2) .Note: Each shim goes halfway around cap (2). Therefore, the shims are removed in pairs. The machine is shipped with 5 shim thicknesses.
Add or remove shims until the desired swing of the grapple is achieved.Use the shims, as needed. (3) 203-3956 Shim ... 1.21 mm (.048 inch)
Replace reaction plates (4) and friction plates (5). Remove all of the shims. The drag of the snubber is low. See the following procedure.Installation Procedure
Upper Joint Assembly
Illustration 4 g00956218
(6) 204-9606 Shim. (7) 204-9607 Shim. (8) Pin.
Illustration 5 g00956219
View A-A (1) Bolt. (2) Cap. (3) 203-3956 Shim. (4) Reaction plate. (5) Friction plate. (9) O-ring seal. (10) Bushing. (11) Lip seal. (12) Pin. (13) Spring. (14) Retaining ring. (15) Bushing.
Install one reaction plate (4) and one friction plate (5) .Note: All friction plates should be dipped in 8T-9579 Oil for five minutes before assembly.Note: A total of five friction plates are required for proper operation.
Insert the pin (12) with retaining ring (14) until the retaining ring touches the first friction plate (5) .
Install the rest of the parts.Note: Install cap (2) with the reversed grease zerk at the top.
Retract the pin (8) far enough in order to slide shims (6,7) between the lug edge and the clevis end. Insert the shims and assemble pin (8) .Use the shims, as needed. (6) 204-9606 Shim ... 2.29 mm (.090 inch) (7) 204-9607 Shim ... 1.52 mm (.060 inch)
Apply 5P-0960 Molybdenum Grease on the bearings and the clutch housing through the grease fittings that are on the bearing. Apply the grease to the clutch housing until grease comes out of the reversed grease zerk.
Repeat Step 5 again after one hour of operation after the initial fill.Lower Joint Assembly
Illustration 6 g00956278
Illustration 7 g01061806
View B-B (1) Bolt (2) Cap (3) 203-3956 Shim (4) Reaction plate (5) Friction plate (6) 204-9606 Shim (7) 204-9607 Shim (8) Pin (9) O-ring seal (10) Bushing (11) Lip seal (12) Pin (13) Spring (14) Retaining ring
Install pin (8) .
Install one reaction plate (4) and one friction plate (5) .Note: All friction plates should be dipped in 8T-9579 Oil for five minutes before assembly.Note: A total of five friction plates are required for proper operation.
Insert the pin (12) with retaining ring (14) to the back of the clutch housing.
Insert shims
Illustration 1 g00956113
Illustration 2 g00956038
View A-AUpper Joint Assembly (1) Bolt. (2) Cap. (3) Shims. (4) Reaction plate. (5) Friction plate.
Illustration 3 g00956037
View B-BLower Joint Assembly (1) Bolt. (2) Cap. (3) Shims. (4) Reaction plate. (5) Friction plate.The amount of drag of the snubber is set with shims (3). In order to increase the drag of the snubber, remove shims. In order to decrease drag of the snubber, add shims.
To adjust the snubber, loosen bolts (1) from cap (2) .Note: Each shim goes halfway around cap (2). Therefore, the shims are removed in pairs. The machine is shipped with 5 shim thicknesses.
Add or remove shims until the desired swing of the grapple is achieved.Use the shims, as needed. (3) 203-3956 Shim ... 1.21 mm (.048 inch)
Replace reaction plates (4) and friction plates (5). Remove all of the shims. The drag of the snubber is low. See the following procedure.Installation Procedure
Upper Joint Assembly
Illustration 4 g00956218
(6) 204-9606 Shim. (7) 204-9607 Shim. (8) Pin.
Illustration 5 g00956219
View A-A (1) Bolt. (2) Cap. (3) 203-3956 Shim. (4) Reaction plate. (5) Friction plate. (9) O-ring seal. (10) Bushing. (11) Lip seal. (12) Pin. (13) Spring. (14) Retaining ring. (15) Bushing.
Install one reaction plate (4) and one friction plate (5) .Note: All friction plates should be dipped in 8T-9579 Oil for five minutes before assembly.Note: A total of five friction plates are required for proper operation.
Insert the pin (12) with retaining ring (14) until the retaining ring touches the first friction plate (5) .
Install the rest of the parts.Note: Install cap (2) with the reversed grease zerk at the top.
Retract the pin (8) far enough in order to slide shims (6,7) between the lug edge and the clevis end. Insert the shims and assemble pin (8) .Use the shims, as needed. (6) 204-9606 Shim ... 2.29 mm (.090 inch) (7) 204-9607 Shim ... 1.52 mm (.060 inch)
Apply 5P-0960 Molybdenum Grease on the bearings and the clutch housing through the grease fittings that are on the bearing. Apply the grease to the clutch housing until grease comes out of the reversed grease zerk.
Repeat Step 5 again after one hour of operation after the initial fill.Lower Joint Assembly
Illustration 6 g00956278
Illustration 7 g01061806
View B-B (1) Bolt (2) Cap (3) 203-3956 Shim (4) Reaction plate (5) Friction plate (6) 204-9606 Shim (7) 204-9607 Shim (8) Pin (9) O-ring seal (10) Bushing (11) Lip seal (12) Pin (13) Spring (14) Retaining ring
Install pin (8) .
Install one reaction plate (4) and one friction plate (5) .Note: All friction plates should be dipped in 8T-9579 Oil for five minutes before assembly.Note: A total of five friction plates are required for proper operation.
Insert the pin (12) with retaining ring (14) to the back of the clutch housing.
Insert shims
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B
311, 311B, 312, 312B, E110B, E120B
311C, 315C, 315D L, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 322, 32...
318C, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 3...
320 L, 320B, 320B L, 320N, 321B, 322 FM L, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330D FM, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, ...
0854734
BEARING
320, 325, E110B, E120B, E200B, E240C, EL240B
320, 325, E110B, E120B, E200B, E240C, EL240B
320 L, 320N, E200B
320 L, 320N, E200B, S305
320, 320 L, 320N, E200B
1R8922
BEARING
E110B, E120B
E110B, E120B
5I5358
BEARING
E110B, E200B
E110B, E200B
0969539
BEARING, UNDER
E110B, E120B, E200B
E110B, E120B, E200B
E110B, E120B, E200B
5I4948
BEARING CAP SET
E200B
E200B
0946182
BEARING
E450
E450
0946170
BEARING
E450
E450
5I5356
BEARING
E110B, E200B
E110B, E200B
5I5336
BEARING
E110B, E120B, E200B
E110B, E120B, E200B
0991460
BEARING
E200B
E200B
0964259
BEARING
E200B
E200B
5I5095
BEARING
E110B, E120B, E200B
E110B, E120B, E200B
E110B, E120B, E200B