0990715 BEARING-SLEEVE Caterpillar parts
311, 311B, 312, 312B, E110B, E120B
Rating:
Alternative (cross code) number:
CA0990715
099-0715
0990715
CA0990715
099-0715
0990715
Weight: 2 pounds 1 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$63.30
12 Oct 2018
300 Hundredths Pounds
CTP: CTP
Caterpillar BUSHING (0990715)
0990715 Weight(lbs): 2.90 Length(cm): 10.1000 Width(cm): 10.1000 Depth(cm): 10.1000
0990715 Weight(lbs): 2.90 Length(cm): 10.1000 Width(cm): 10.1000 Depth(cm): 10.1000
12 Oct 2018
400 Hundredths Pounds
CTP: CTP
0990715 Bushing Fits Caterpillar 312
Warranty
Warranty
Number on catalog scheme:
2
For full view, you need register
Information:
Probable Causes
The probable root causes are listed in order below:
Customer Specified Parameters (normal operation)
Cold Mode Operation
Individual malfunctioning cylinder
"Power train Data Link"
Personality Module
Torque Limit SwitchRecommended Actions
Perform the following diagnostic procedures in order:
Check Customer Specified Parameters.
Verify that the complaint is not normal operation (programmed parameter).
Connect an Electronic Service Tool.
Check the following parameters:
"Lower Gears Engine RPM Limit"
"Intermediate Gears Engine RPM Limit"
"Gear Down Protection Engine RPM Limit"
Set each parameter to the parameter's maximum value one at a time and determine whether the problem is corrected.
Check Cold Mode Operation.Note: This is normal operation if the problem occurs only after start-up in cold weather.
Connect an Electronic Service Tool.
Monitor the Electronic Service Tool in order to verify that the engine has progressed from Cold Mode.An Active Cold Mode is indicated in the upper corner of any Status Screen.
Check for an individual malfunctioning cylinder.
Ensure that the Electronic Unit Injector Connector (J300/P300) is fully connected and ensure that the Electronic Unit Injector Connector (J300/P300) is free of corrosion.
Ensure that the ECM Engine Harness Connector (J2/P2) is fully connected and ensure that the Engine Harness Connector (J2/P2) is free of corrosion.
Connect an Electronic Service Tool. Use the Cylinder Cutout Test. Access the Cylinder Cutout Test by selecting the "Diagnostic Menu" and the "Diagnostics Test Menu". Run the Cylinder Cutout Test in order to disable each cylinder. Disabling each cylinder allows the technician to isolate the misfiring cylinders.If the misfiring cylinder can be isolated to a specific cylinder, refer to Troubleshooting, "Injector Solenoid Circuit - Test".
Check the "Power train Data Link". Ensure that the SAE J1922 or the SAE J1939 Power train Data Link is not limiting the power.
Connect an Electronic Service Tool.
Monitor the "Power train Data Link" Status screen while the vehicle is experiencing problems.If the "Power train Data Link" Status screen indicates that the "Power train Data Link" is limiting the power or the rpm, verify that this is not normal operation. If this is not normal operation, refer to the vehicle OEM for repairs.
Check the ECM or the Personality Module.
Connect an Electronic Service Tool.
Verify that the correct Personality Module has been installed.Refer to Troubleshooting, "ECM Memory - Test".
Check the Torque Limit Switch.
Connect an Electronic Service Tool.
Check the setting for the Customer Parameter for the "Torque Limit".If the "Torque Limit" is programmed below 3400 N m (2500 lb ft), check the status screen for the Torque Limit Switch. Ensure that the status screen indicates that the Torque Limit Switch is OFF. If the status of the Torque Limit Switch is ON and a "Torque Limit" is programmed, the system is operating correctly. If the switch that is connected to this signal input is not switching ON and switching OFF, refer to Troubleshooting, "PTO Switch Circuit - Test".
The probable root causes are listed in order below:
Customer Specified Parameters (normal operation)
Cold Mode Operation
Individual malfunctioning cylinder
"Power train Data Link"
Personality Module
Torque Limit SwitchRecommended Actions
Perform the following diagnostic procedures in order:
Check Customer Specified Parameters.
Verify that the complaint is not normal operation (programmed parameter).
Connect an Electronic Service Tool.
Check the following parameters:
"Lower Gears Engine RPM Limit"
"Intermediate Gears Engine RPM Limit"
"Gear Down Protection Engine RPM Limit"
Set each parameter to the parameter's maximum value one at a time and determine whether the problem is corrected.
Check Cold Mode Operation.Note: This is normal operation if the problem occurs only after start-up in cold weather.
Connect an Electronic Service Tool.
Monitor the Electronic Service Tool in order to verify that the engine has progressed from Cold Mode.An Active Cold Mode is indicated in the upper corner of any Status Screen.
Check for an individual malfunctioning cylinder.
Ensure that the Electronic Unit Injector Connector (J300/P300) is fully connected and ensure that the Electronic Unit Injector Connector (J300/P300) is free of corrosion.
Ensure that the ECM Engine Harness Connector (J2/P2) is fully connected and ensure that the Engine Harness Connector (J2/P2) is free of corrosion.
Connect an Electronic Service Tool. Use the Cylinder Cutout Test. Access the Cylinder Cutout Test by selecting the "Diagnostic Menu" and the "Diagnostics Test Menu". Run the Cylinder Cutout Test in order to disable each cylinder. Disabling each cylinder allows the technician to isolate the misfiring cylinders.If the misfiring cylinder can be isolated to a specific cylinder, refer to Troubleshooting, "Injector Solenoid Circuit - Test".
Check the "Power train Data Link". Ensure that the SAE J1922 or the SAE J1939 Power train Data Link is not limiting the power.
Connect an Electronic Service Tool.
Monitor the "Power train Data Link" Status screen while the vehicle is experiencing problems.If the "Power train Data Link" Status screen indicates that the "Power train Data Link" is limiting the power or the rpm, verify that this is not normal operation. If this is not normal operation, refer to the vehicle OEM for repairs.
Check the ECM or the Personality Module.
Connect an Electronic Service Tool.
Verify that the correct Personality Module has been installed.Refer to Troubleshooting, "ECM Memory - Test".
Check the Torque Limit Switch.
Connect an Electronic Service Tool.
Check the setting for the Customer Parameter for the "Torque Limit".If the "Torque Limit" is programmed below 3400 N m (2500 lb ft), check the status screen for the Torque Limit Switch. Ensure that the status screen indicates that the Torque Limit Switch is OFF. If the status of the Torque Limit Switch is ON and a "Torque Limit" is programmed, the system is operating correctly. If the switch that is connected to this signal input is not switching ON and switching OFF, refer to Troubleshooting, "PTO Switch Circuit - Test".
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E110B, E120B
307B, 311, 311B, 312, 312B, 312B L, 313B, 320 L, 320B, 320C, 320N, 322B L, 322C, 322C FM, 325, 325 L, 325B L, 325C, 330B L, 350, 350 L, 375, 375 L
307B, 308D, 311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 313B, 314C, 320B, 320C, 320D, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 325B L, 325C, 325C L, 325D, 325D L, 329D L, 330B L, 330C, 330C ...
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
308C, 308D, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 320D, 320D L, 320D2, 320D2 L, 320E, ...
311B, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315, 315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320C, 3...
311B, 311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315, 315B, 315C, 315D L, 317B LN, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320B U, 320C, 3...
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN
0990334
BEARING AS-NEEDLE
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
0990322
BEARING-ROLLER
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 3...
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR
311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L
0931812
BEARING-SLEEVE
311, 315, 317, E110, E110B, E140, E180, E70
311, 315, 317, E110, E110B, E140, E180, E70
1057385
BEARING-SLEEVE
315, 315B L, 317, 317B LN, 318B
315, 315B L, 317, 317B LN, 318B
315, 315B, 315B L, 315C, 317, 317B LN, 318B, 320 L
1163588
BEARING-SLEEVE
315, 317, HYDRAULIC
315, 317, HYDRAULIC
313D2 LGP, 315, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 3...
307C, 308C, 311C, 312, 312B L, 312C, 312C L, 314C, 315C, 315D L