1057366 BEARING-SLEEVE Caterpillar parts
315, 315B, 315B L, 315C, 317, 317B LN, M313C, M313D, M315D 2, M318, M318C, M318C MH, M318D, M318D MH, M322D, M322D MH
Rating:
Alternative (cross code) number:
CA1057366
105-7366
1057366
CA1057366
105-7366
1057366
Weight: 2 pounds 1 kg.
Information:
ID
70.23
mm
OD
85.16
mm
WIDTH
85
mm
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YNRSP 1057366 Bushing Sleeve Bearing for Heavy Equipment (1Pcs)
YNRSP Brand: YNRSP || Part Number: 1057366 || Part Type: Bushing || Weight: 2.64 lbs (1.2 kg) || Fits Model: 3046, 3054, 3054C, 3054E, 3056E, 3116, C4.4, C6.6, 315, 315B L
YNRSP Brand: YNRSP || Part Number: 1057366 || Part Type: Bushing || Weight: 2.64 lbs (1.2 kg) || Fits Model: 3046, 3054, 3054C, 3054E, 3056E, 3116, C4.4, C6.6, 315, 315B L
1057366 105-7366 Bushing,Bearing as fits Caterpillar cat e320d 319d 323d 324d
FARWAY Aftermarket Replacent Parts; 3 Months Warranty
FARWAY Aftermarket Replacent Parts; 3 Months Warranty
Number on catalog scheme:
18A
For full view, you need register
Compatible equipment models: 1057366:
Information:
Check the exciter armature. Ensure that the rotating rectifier is tight. If a failure of a rectifier is suspected, proceed to the "Testing a Three-Diode Rectifier Block" section.Testing a Three-Diode Rectifier Block
Illustration 1 g00610240
Illustration 2 g00613971
Three-Diode Rectifier Block (two pieces)
The following procedure tests all three diodes within a block. Check the positive rectifier block and the negative rectifier block. If any meter reading does not fall within the given ranges, replace the rectifier block.
Set the digital multimeter on the diode range. Remove all leads from the rectifier block.
To test the negative rectifier block, follow these steps:
Place the red test lead on the negative "-" terminal. Place the black test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). All readings on the meter should be between 0.4 and 1.0.
Place the black test lead on the negative "-" terminal. Place the red test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). In all cases, the meter should read "OL" (overload).
To test the positive rectifier block, follow these steps:
Place the red test lead on the positive "+" rectifier terminal. Place the black test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). In all cases, the meter should read "OL" (overload).
Place the black test lead on the positive "+" rectifier terminal. Place the red test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). All readings on the meter should be between 0.4 and 1.0. Note: A shorted diode can damage the exciter rotor. If a diode is shorted, check the exciter rotor. Refer to the Testing and Adjusting, "Winding - Test" and Testing and Adjusting, "Insulation - Test". Perform these tests.Note: This rectifier block also contains varistor "CR7". "CR7" can be checked by measuring the resistance between the positive "+" rectifier terminal and the negative "-" rectifier terminal. The resistance should be a minimum of 15000 ohms.
Illustration 1 g00610240
Illustration 2 g00613971
Three-Diode Rectifier Block (two pieces)
The following procedure tests all three diodes within a block. Check the positive rectifier block and the negative rectifier block. If any meter reading does not fall within the given ranges, replace the rectifier block.
Set the digital multimeter on the diode range. Remove all leads from the rectifier block.
To test the negative rectifier block, follow these steps:
Place the red test lead on the negative "-" terminal. Place the black test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). All readings on the meter should be between 0.4 and 1.0.
Place the black test lead on the negative "-" terminal. Place the red test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). In all cases, the meter should read "OL" (overload).
To test the positive rectifier block, follow these steps:
Place the red test lead on the positive "+" rectifier terminal. Place the black test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). In all cases, the meter should read "OL" (overload).
Place the black test lead on the positive "+" rectifier terminal. Place the red test lead on the following rectifier terminals: "AC1" (3), "AC2" (4) and "AC3" (5). All readings on the meter should be between 0.4 and 1.0. Note: A shorted diode can damage the exciter rotor. If a diode is shorted, check the exciter rotor. Refer to the Testing and Adjusting, "Winding - Test" and Testing and Adjusting, "Insulation - Test". Perform these tests.Note: This rectifier block also contains varistor "CR7". "CR7" can be checked by measuring the resistance between the positive "+" rectifier terminal and the negative "-" rectifier terminal. The resistance should be a minimum of 15000 ohms.
Cat SIS web machinery list:
Parts bearing Caterpillar catalog:
311C, 315C, 315D L, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 322, 32...
311C, 315C, 315D L, 318B, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 322, 32...
318B, 320 L, 320B, 320N, 322, 322 FM L, 322 LN, 322B L, 322C FM, 325, 325 L, 325 LN, 325B L, 330, 330 FM L, 330B L, 345B L, 350, 350 L, 5080, HYDRAULIC, M315C, M315D, M316C, M316D, M317D 2, M320, M322...
318B, 320 L, 322B L, 325, 325 LN, 325B L, 330B L, M320, M322C, M322D, M322D MH
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 318B, 320B, 320C, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B L, 325C, 325C FM, 325C L, 325D MH, 330C, 34...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320...
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
311C, 312C, 312C L, 314C, 315C
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, ...
M318C, M318C MH, M318D, M318D MH
324D, 325B L, 325C, 325C FM, 325D FM, 325D FM LL, 329D LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 33...
527, 908, D5R LGP, D6K2, D6K2 LGP, D6N, D6N LGP, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, GSH15, GSH15-60, GSH22B, GSH9, GSH9B, M313C, M315C, M318C, M318C MH, M318D MH, M322C, M322D MH, M325C MH
308C, 308D, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 320D, 320D L, 320D2, 320D2 L, 320E, ...
315, 315B, 315B L, 317, 317B LN, 318B, 320B, 320B L, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B L, 330B L, 345B L, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, ...
0931812
BEARING-SLEEVE
311, 315, 317, E110, E110B, E140, E180, E70
311, 315, 317, E110, E110B, E140, E180, E70
1057385
BEARING-SLEEVE
315, 315B L, 317, 317B LN, 318B
315, 315B L, 317, 317B LN, 318B
315, 315B, 315B L, 315C, 317, 317B LN, 318B, 320 L
1163588
BEARING-SLEEVE
315, 317, HYDRAULIC
315, 317, HYDRAULIC
8U5666
BEARING-ROLLER
206, 206B, 212, 212B, M315, M315C, M316C, M318
206, 206B, 212, 212B, M315, M315C, M316C, M318
M312, M313C, M313D, M315, M315C, M316C, M318
5W8680
BEARING
206, 206B, 212, 212B, 214B, 224B, M312, M315, M318, M320
206, 206B, 212, 212B, 214B, 224B, M312, M315, M318, M320
1026461
BEARING AS-ROLLER
315, 315B, 315B L, 317, 317B LN
315, 315B, 315B L, 317, 317B LN
311D LRR, 312B L, 312C, 312D, 312E, 314D LCR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320D...
315, 317, 320 L, 322 FM L, 325, 325 L, 325 LN, 350 L