1128971 BEARING GP-PILLOW BLOCK Caterpillar parts
950G, 950G II, 950H, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
Rating:
Alternative (cross code) number:
CA1128971
112-8971
1128971
CA1128971
112-8971
1128971
Weight: 15 pounds 7 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YNRSP 1128971 Bearing for Heavy Equipment
YNRSP Brand: YNRSP || Part Number: 1128971 || Part type: Bearing || Weight: 16.8 lbs (7.63 kg) || Fits Model: 3126, 3126B, C7, IT62G, IT62G II, IT62H, 950G, 950G II, 950H, 962G
YNRSP Brand: YNRSP || Part Number: 1128971 || Part type: Bearing || Weight: 16.8 lbs (7.63 kg) || Fits Model: 3126, 3126B, C7, IT62G, IT62G II, IT62H, 950G, 950G II, 950H, 962G
This part in 4 request:
Show.
This information for suppliers only!
2024-07-25
2023-02-28
2022-04-19
2018-04-06
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 1128971:
Information:
Disassemble Governor Drive
start by:a) separation of governor from governor drive 1. Remove locknut (2) and loosen bolt (1) one complete turn. 2. Put the governor drive on wooden blocks. Use a brass punch and hammer to hit (tap) bolt (1) to loosen gear (3) from shaft (5).3. Install a 5/16"-18 NC jam nut on bolt (4) even with the end of bolt (4). Use a brass punch and hammer to loosen the bolt from the lever.4. Remove bolt (1), washer, jam nut and bolt (4).5. Remove gear (3) and shaft (5). 6. Remove lever and shaft assembly (7), lever (8) and shaft (6). 7. Inspect bearing (9) for wear and damage. If a replacement is needed, use tooling (A) to remove it.8. Inspect seal (10) for wear and damage. If a replacement is needed, the seal must be destroyed to be removed.9. Inspect bearings (11) for wear and damage. If replacements are needed, use tooling (A) to remove these.Assemble Governor Drive
1. If bearing (2) was removed, make an alignment of the oil holes in the bearing and housing (1). Use tooling (A) to install bearing (2) even with the face of housing (1). 2. If bearing (3) was removed, install the bearing with tooling (A) approximately 0.30 in. (7.6 mm) above the face of housing (1).3. If bearing (4) was removed, install the bearing with tooling (A) even with the bottom of the seal counterbore.4. Install seal (5), with the lips of the seal toward the inside, with tooling (A) to the bottom of the seal counterbore. Put a small amount of engine oil on the lip of seal (5). 5. Put shaft (6) and lever (9) in position in housing (1).6. Put lever and shaft assembly (8) in position in housing (1) through lever (9). Make sure the end of lever (9) is engaged in the groove of shaft (6).
Before dowel (7) is installed make sure the end of shaft (8) does not make contact with the inner face of bearing (3). If the end of shaft (8) makes contact with the inner face of bearing (3), move the bearing away from the end of the shaft.
7. Install dowel (7) that holds shaft (8) in place.8. Fasten lever (9) to shaft (8) with the taper bolt and locknut. 9. Put shaft (11) in position in housing (1).10. Install gear (10) on shaft (11).end by:a) connection of governor to governor drive
start by:a) separation of governor from governor drive 1. Remove locknut (2) and loosen bolt (1) one complete turn. 2. Put the governor drive on wooden blocks. Use a brass punch and hammer to hit (tap) bolt (1) to loosen gear (3) from shaft (5).3. Install a 5/16"-18 NC jam nut on bolt (4) even with the end of bolt (4). Use a brass punch and hammer to loosen the bolt from the lever.4. Remove bolt (1), washer, jam nut and bolt (4).5. Remove gear (3) and shaft (5). 6. Remove lever and shaft assembly (7), lever (8) and shaft (6). 7. Inspect bearing (9) for wear and damage. If a replacement is needed, use tooling (A) to remove it.8. Inspect seal (10) for wear and damage. If a replacement is needed, the seal must be destroyed to be removed.9. Inspect bearings (11) for wear and damage. If replacements are needed, use tooling (A) to remove these.Assemble Governor Drive
1. If bearing (2) was removed, make an alignment of the oil holes in the bearing and housing (1). Use tooling (A) to install bearing (2) even with the face of housing (1). 2. If bearing (3) was removed, install the bearing with tooling (A) approximately 0.30 in. (7.6 mm) above the face of housing (1).3. If bearing (4) was removed, install the bearing with tooling (A) even with the bottom of the seal counterbore.4. Install seal (5), with the lips of the seal toward the inside, with tooling (A) to the bottom of the seal counterbore. Put a small amount of engine oil on the lip of seal (5). 5. Put shaft (6) and lever (9) in position in housing (1).6. Put lever and shaft assembly (8) in position in housing (1) through lever (9). Make sure the end of lever (9) is engaged in the groove of shaft (6).
Before dowel (7) is installed make sure the end of shaft (8) does not make contact with the inner face of bearing (3). If the end of shaft (8) makes contact with the inner face of bearing (3), move the bearing away from the end of the shaft.
7. Install dowel (7) that holds shaft (8) in place.8. Fasten lever (9) to shaft (8) with the taper bolt and locknut. 9. Put shaft (11) in position in housing (1).10. Install gear (10) on shaft (11).end by:a) connection of governor to governor drive
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
936F, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
854G, 950G, 950G II, 950H, 962G, 962G II, 962H, D10N, D10R, D10T, D9L, IT62G, IT62G II, IT62H
950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
928HZ, 930G, 950 GC, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
950G, 950H, 950K, 962H, 962K, 966M, 966M XE, 972M, 972M XE, IT62H
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D...
834G, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 980H, 988G, 988H, 992G, 992K
950G, 950G II, 950H, 962G, 962G II, 962H, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G, 972G II, 972H, 972M, 972M XE, R1300, R1300G, R1300G II
950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H
950G II, 950H, 962G II, 962H
814F, 815F, 816F, 950H, 962G, 966F, 966F II, 970F, R1600
936F, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966H, 966K, 966M, IT62G, IT62G II, IT62H, R1300, R1300G, R1300G II
2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 950G, 950G II, 950H, 9...
1118898
BEARING
633E II
633E II
350, 365C, 365C L, 365C L MH, 374D L, 375, 375 L, 5080, 550, 550B, 560B, 570, 570B, 580, 580B, 631E, 631G, 633E II, 637E, 637G, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 797, 797B, 797F, 844, ...
1118523
BEARING
631E, 631G, 633E II, 637E, 637G, D9T
631E, 631G, 633E II, 637E, 637G, D9T
631E, 631G, 633E II, 637E, 637G, D9T
1633922
BEARING
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G, R1600, R1700G, R2900
824G, 825G, 826G, 950G, 962G, 966G, 972G, 980G, IT62G, R1600, R1700G, R2900
928HZ, 930G, 950 GC, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 960F, 962G, 962G II, 962H, IT62G, IT62G II, IT62H
854G, 950G, 950G II, 950H, 962G, 962G II, 962H, D10N, D10R, D10T, D9L, IT62G, IT62G II, IT62H
4E9665
BEARING
824G, 825G, 826G, 844, 854G, 950G, 962G, 966G, 972G, 980G, 990, 990 II, 992G, IT62G, R1600, R2900
824G, 825G, 826G, 844, 854G, 950G, 962G, 966G, 972G, 980G, 990, 990 II, 992G, IT62G, R1600, R2900
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H