1433836 BEARING-SLEEVE Caterpillar parts
M312
Rating:
Alternative (cross code) number:
CA1433836
143-3836
1433836
CA1433836
143-3836
1433836
Weight: 1 pounds 0 kg.
Information:
ID
70.23
mm
OD
85.16
mm
WIDTH
45
mm
WHEELED EXCAVATOR,
Compatible equipment models: 1433836:
Number on catalog scheme:
7A
For full view, you need register
Information:
Illustration 1 g02160341
Schematic of the Cat Data Link CircuitThis diagnostic code is recorded when the Implement (Screed) ECM does not receive the expected information from the Machine ECM.Note: The Implement (Screed) ECM is located under the Implement (Screed) Platform.The likely possible causes of this diagnostic code are listed below:
The software that is installed on the Machine ECM is incorrect.
The software that is installed on the Implement (Screed) ECM is incorrect.System Response:Select display features may not function properly.Test Step 1. VERIFY THE HARDWARE AND THE SOFTWARE PART NUMBERS.
Verify that the following information is correct:
The part number of the software of the Implement (Screed) ECM
The part number of the Machine ECM software
The part number of the Implement (Screed) ECM
The part number of the Machine ECM Note: Consult the Business Unit that produces the product for the correct part numbers of the configuration software. Expected Result:All part numbers are correct. Results:
OK - All part numbers are correct. Proceed to test step 2.
NOT OK - All part numbers are NOT correct. The part number of the Implement (Screed) ECM may be incorrect. The part number of the Machine ECM may be incorrect. The incorrect configuration software may also be installed. Repair: Replace the incorrect ECM with an ECM that has the correct part number. Flash the correct configuration software. See Troubleshooting, "Electronic Control Module - Flash Program".STOPTest Step 2. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch to the OFF position.
Inspect all harness connections that are related to the Cat Data Link. Make sure that the connectors are clean and tight.
Check the connectors for proper mating.
Check the wires at the connector.
Check each wire for nicks or signs of abrasion in the insulation.
Check for moisture at the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and check each socket of the machine harness connectors. Expected Result:The machine harness connectors are tight and free of corrosion. Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to test step 3.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness. STOPTest Step 3. CHECK FOR SHORTS TO GROUND.
The disconnect switch remains in the OFF position.
Disconnect the machine harness from all electronic control modules that use the Cat Data Link.
At the machine harness for the Implement (Screed) ECM, measure the resistance between frame ground and connector contacts J1-10 (wire 944-OR) and J1-20 (wire 945-BR) of the Cat Data Link circuit. Expected Result:The resistance is greater than 5000 ohms. Results:
OK - The resistance is greater than 5000 ohms. The harness circuit resistance is correct. Proceed to test step 4.
NOT OK - The resistance is less than 5000 ohms. The machine harness has failed. Repair: There is a short between frame ground and the Cat Data Link circuit in the machine harness. Repair the machine harness or replace the machine harness. STOPTest Step 4. CHECK FOR A SHORT TO THE +BATTERY CIRCUIT.
The disconnect switch remains in the OFF position.
All related electronic control
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
206, 212, 3054, 3054B, 3056, 3056E, 307, 312, 312B L, 312C, 315, 315B L, 317, 416, 416B, 416C, 416D, 420D, 424D, 426B, 426C, 428, 428B, 428C, 428D, 430D, 432D, 436C, 438B, 438C, 438D, 442D, 550B, 554,...
527, 65, 65C, 65E, 75, 75C, 75D, 75E, 85C, 85D, 85E, 943, 95E, CP-433C, CP-433E, CP-44, CP-56, CP-563, CP-573E, CP-64, CP-68B, CP-74B, CS-323C, CS-433C, CS-433E, CS-44, CS-533, CS-533C, CS-533D, CS-56...
AP-1000B, AP-900B, BG-260D, CB-214B, CW-34, M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318D, M318D MH, RT100, RT50, TH103, TH62, TH63, TH82, TH83
307B, 308D, 311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 313B, 314C, 320B, 320C, 320D, 322B L, 322C, 322C FM, 323D L, 324D, 324D L, 325B L, 325C, 325C L, 325D, 325D L, 329D L, 330B L, 330C, 330C ...
308C, 308D, 311, 311B, 311C, 311D LRR, 312D, 312D L, 312E, 312E L, 313D, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 320D, 320D L, 320D2, 320D2 L, 320E, ...
M312, M313C, M313D, M315, M315C, M316C, M318
213B, 214B, 224B, M312, M315, M318, M320
307B, 311C, 312C, 312C L, 314C, 320C, 325C, 330C, 330C L, M312
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320C, 320D, 320D L, 320D2, 320D2 L, 32...
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
2024124
BEARING GP-SELF-ALIGNING
M312, M313C, M315, M315C, M316C, M318C, M318C MH, M322C
M312, M313C, M315, M315C, M316C, M318C, M318C MH, M322C
307B, 311C, 312C, 312C L, 314C, 320C, 325C, 330C, 330C L, M312
1307814
BEARING
M312, M313C, M313D, M315D 2
M312, M313C, M313D, M315D 2
1324306
BEARING-ROLLER
M312, M313C
M312, M313C
1324298
BEARING-ROLLER
M312, M313C
M312, M313C
1324292
BEARING AS-NEEDLE
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318, M318C, M318C MH, M318D, M318D MH, M320, M322C, M322D, M322D MH
1307829
BEARING
M312, M313C, M313D, M315D 2
M312, M313C, M313D, M315D 2
1314646
BEARING
777G, 785D, M312
777G, 785D, M312
8U5508
BEARING-ROLLER
205B, 206B, 572R, 572R II, 623H, 623K, 623K LRC, M312
205B, 206B, 572R, 572R II, 623H, 623K, 623K LRC, M312
1179435
BEARING-SLEEVE
M312, M313C, M313D, M315D 2, M317D 2
M312, M313C, M313D, M315D 2, M317D 2
1056343
BEARING-SLEEVE
307, 307B, M312, M318, M318D MH, M320, M322D MH, M325C MH
307, 307B, M312, M318, M318D MH, M320, M322D MH, M325C MH
315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, 324E...
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320C, 320D, 320D L, 320D2, 320D2 L, 32...