1550838 BEARING AS-ROLLER Caterpillar parts
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
Rating:
Alternative (cross code) number:
CA1550838
155-0838
1550838
CA1550838
155-0838
1550838
Weight: 0.35 pounds 0 kg.
WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$196.97
23 Apr 2024
US: Fast 404
1550838 Bearing As Fits CATERPILLARR Models 1550838
MAXCBD Part Number: 1550838
MAXCBD Part Number: 1550838
03 Oct 2017
BLQ: BLQ
1550838 BEARING AS
1550838 BEARING AS
1550838 BEARING AS
This part in 5 request:
Show.
This information for suppliers only!
2021-10-27
2021-07-02
2021-06-02
2019-05-08
2019-05-08
Number on catalog scheme:
21
For full view, you need register
Compatible equipment models: 1550838:
Information:
Event E031Conditions Which Generate This Code:The Electronic Control Module (ECM) detects the following condition:
The air inlet pressure for the left turbocharger is above the default pressure of 7 kPa (28 inches of H2O) for five seconds.
The air inlet pressure for the right turbocharger is above the default pressure of 7 kPa (28 inches of H2O) for five seconds.System Response:The event is logged. When the air inlet restriction exceeds 7 kPa (28 inches of H2O) the ECM will derate the engine. The ECM will derate the engine in increments of 2% per 1 kPa (4 inches of H2O) up to a maximum derate level of 25%. Air filter restriction is determined by measuring the atmospheric pressure and the turbocharger inlet pressures and calculating the difference.Possible Performance Effect:
Low powerTroubleshooting:
There may be a problem with the air inlet system.
There may be a problem with the atmospheric pressure sensor or the left or right turbocharger inlet pressure sensors.Test Step 1. Check for "ACTIVE" Diagnostic Codes.
Start the Caterpillar Electronic Technician (ET).
Turn the main power to the ON position.
Check for any active diagnostic codes or logged diagnostic codes. Expected Result:No diagnostic codes are present.Results:
OK - No diagnostic codes are present. Proceed to Test Step 2.
Not OK - Diagnostic codes are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem.STOPTest Step 2. Perform a Check of the Air Inlet System.
Check for restrictions in the air inlet system. Refer to the Testing and Adjusting manual for information on inspecting the air inlet system. Expected Result:There are no problems with the air inlet system.Results:
OK - There are no problems with the air inlet system. There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem.STOP
Not OK - There is a problem with the air inlet system.Repair: Repair the problem. Ensure that the repair eliminates the problem.STOP
The air inlet pressure for the left turbocharger is above the default pressure of 7 kPa (28 inches of H2O) for five seconds.
The air inlet pressure for the right turbocharger is above the default pressure of 7 kPa (28 inches of H2O) for five seconds.System Response:The event is logged. When the air inlet restriction exceeds 7 kPa (28 inches of H2O) the ECM will derate the engine. The ECM will derate the engine in increments of 2% per 1 kPa (4 inches of H2O) up to a maximum derate level of 25%. Air filter restriction is determined by measuring the atmospheric pressure and the turbocharger inlet pressures and calculating the difference.Possible Performance Effect:
Low powerTroubleshooting:
There may be a problem with the air inlet system.
There may be a problem with the atmospheric pressure sensor or the left or right turbocharger inlet pressure sensors.Test Step 1. Check for "ACTIVE" Diagnostic Codes.
Start the Caterpillar Electronic Technician (ET).
Turn the main power to the ON position.
Check for any active diagnostic codes or logged diagnostic codes. Expected Result:No diagnostic codes are present.Results:
OK - No diagnostic codes are present. Proceed to Test Step 2.
Not OK - Diagnostic codes are present.Repair: Repair the diagnostic codes that are present. Refer to the appropriate topic in the "Troubleshooting With a Diagnostic Code" section of this manual. Ensure that the repair eliminates the problem.STOPTest Step 2. Perform a Check of the Air Inlet System.
Check for restrictions in the air inlet system. Refer to the Testing and Adjusting manual for information on inspecting the air inlet system. Expected Result:There are no problems with the air inlet system.Results:
OK - There are no problems with the air inlet system. There may be an intermittent problem.Repair: Monitor the operation of the engine. Repair the problem. Ensure that the repair eliminates the problem.STOP
Not OK - There is a problem with the air inlet system.Repair: Repair the problem. Ensure that the repair eliminates the problem.STOP
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
M312, M313C, M313D, M315, M315C, M316C, M318
206B, 212B, M315, M315C, M316C, M318, M318C, M318C MH, M320, M322C
315B L, 317B LN, M313C, M313D, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318
M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, M318
213B, 214B, 224B, M312, M315, M318, M320
M313C, M313D, M315, M315D 2
307B, 311C, 312C, 312C L, 314C, 320C, 325C, 330C, 330C L, M312
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320C, 320D, 320D L, 320D2, 320D2 L, 32...
318B, 320 L, 320B, 320N, 322, 322 FM L, 322 LN, 322B L, 322C FM, 325, 325 L, 325 LN, 325B L, 330, 330 FM L, 330B L, 345B L, 350, 350 L, 5080, HYDRAULIC, M315C, M315D, M316C, M316D, M317D 2, M320, M322...
322B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330B L, 345B, 345B II, 345B II MH, 345B L, M315C, M315D, M316C, M316D, M317D 2, P115, S115, VPC-30, VPS-35, W345B II
330, 330 FM L, 330 L, 330D, M315C, M315D, M316C, M316D, M317D 2, P115
527, 908, D5R LGP, D6K2, D6K2 LGP, D6N, D6N LGP, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, GSH15, GSH15-60, GSH22B, GSH9, GSH9B, M313C, M315C, M318C, M318C MH, M318D MH, M322C, M322D MH, M325C MH
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2
M312, M313C, M313D, M315, M315C, M315D, M315D 2, M316C, M316D, M317D 2, PC206, PC310B
2443064
BEARING-SLEEVE
301.4C, 301.5, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.7D
301.4C, 301.5, 301.7D, 301.7D CR, 302.2D, 302.4D, 302.5, 302.7D
1397352
BEARING
301.5
301.5
1397344
BEARING
301.5
301.5
1347564
BEARING
313B
313B
1347563
BEARING
313B
313B
1347558
BEARING
313B
313B
1367711
BEARING
M315
M315
1367717
BEARING
M312
M312
2024124
BEARING GP-SELF-ALIGNING
M312, M313C, M315, M315C, M316C, M318C, M318C MH, M322C
M312, M313C, M315, M315C, M316C, M318C, M318C MH, M322C