1615811 BEARING Caterpillar parts
992G, 992K
Rating:
Alternative (cross code) number:
CA1615811
161-5811
1615811
CA1615811
161-5811
1615811
Weight: 51 pounds 23 kg.
Information:
ID
180.39
mm
OD
230.25
mm
WIDTH
196
mm
WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1615811 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP 1615811 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01251848
Typical example
Remove the bolts from retainers (2) and (6).
Remove the bolts from support bracket (4).
Remove tube (5) and the O-ring seals.
Remove the bolts from elbow (1). Remove elbow (1) and the gasket.
Disconnect the harness assembly from pressure sensor (3). Remove the bolts from pressure sensor (3). Remove pressure sensor (3).
Illustration 2 g00593655
Typical example
Remove mounting straps (7) and (9) that hold the water temperature regulator housing to the engine oil filter housing. Remove plate (8) from the engine oil filter housing.
Illustration 3 g01251850
Typical example
Attach Tooling (A) and a suitable lifting device to water temperature regulator housing (12). The weight of water temperature regulator housing (12) is approximately 59 kg (130 lb).
Remove bolts (11) and water temperature regulator housing (12) from exhaust manifold (13).
Remove the O-ring seals from water temperature regulator housing (12).
Remove regulator housing (10) from water temperature regulator housing (12).
Illustration 4 g01251884
Typical example
Remove water temperature regulators (14) from regulator housing (10).
Remove the valve assembly and the seals, if necessary.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01251848
Typical example
Remove the bolts from retainers (2) and (6).
Remove the bolts from support bracket (4).
Remove tube (5) and the O-ring seals.
Remove the bolts from elbow (1). Remove elbow (1) and the gasket.
Disconnect the harness assembly from pressure sensor (3). Remove the bolts from pressure sensor (3). Remove pressure sensor (3).
Illustration 2 g00593655
Typical example
Remove mounting straps (7) and (9) that hold the water temperature regulator housing to the engine oil filter housing. Remove plate (8) from the engine oil filter housing.
Illustration 3 g01251850
Typical example
Attach Tooling (A) and a suitable lifting device to water temperature regulator housing (12). The weight of water temperature regulator housing (12) is approximately 59 kg (130 lb).
Remove bolts (11) and water temperature regulator housing (12) from exhaust manifold (13).
Remove the O-ring seals from water temperature regulator housing (12).
Remove regulator housing (10) from water temperature regulator housing (12).
Illustration 4 g01251884
Typical example
Remove water temperature regulators (14) from regulator housing (10).
Remove the valve assembly and the seals, if necessary.
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
992G
834G, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, 980G, 980G II, 980H, 988G, 988H, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
992G
992G
992G
992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
844, 854G, 990 II, 992G
797, 834G, 834H, 836G, 836H, 844K, 854K, 988G, 988H, 990K, 992K, 993K, D8T, D9T
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 844K, 854K, 990K, 99...
992G
1020746
BEARING AS
375, 375 L, 5080, 5130, 5130B, 5230, 854G, 992G
375, 375 L, 5080, 5130, 5130B, 5230, 854G, 992G
844, 854G, 990 II, 992G
1409692
BEARING
950G, 962G, 966G, 972G, 980G
950G, 962G, 966G, 972G, 980G
950G, 962G, 980G
9U0578
BEARING
990, 990 II
990, 990 II
2290814
BEARING
992G
992G
2290798
BEARING
992G
992G
992G
1615810
BEARING
992G
992G
1461617
BEARING
992G
992G