1995358 BEARING Caterpillar parts
247, 247B, 267, 267B, 287
Rating:
Alternative (cross code) number:
CA1995358
199-5358
1995358
CA1995358
199-5358
1995358
Weight: 0.93 pounds 0 kg.
MULTI TERRAIN LOADER,
Number on catalog scheme:
1
For full view, you need register
Information:
4. Pull out the knob to release the transmission control lock.It is possible to start the engine when the transmission control lever is in FORWARD or REVERSE, but the machine will not move. Should this happen, move the lever to NEUTRAL, then to the desired speed and direction.
Be sure the area is clear of personnel and obstructions.
5. Move the transmission control to the desired travel direction. Rotate the control to the desired speed. 6. Depress the accelerator pedal.Drive the machine forward for best visibility and control.
For operator safety and comfort and maximum service life of power train components, deceleration and/or braking is recommended before any directional shifts are made.
Emergency Brake System
If the brake system air pressure drops below normal operating pressure, a warning horn will sound. The low brake pressure and the parking brake indicators on the operator's panel will light up. The fault light will start flashing.If the pressure drops further, the parking/emergency brake will apply automatically and the transmission will shift to neutral.Be prepared for a sudden stop. Correct the reason for the loss of air pressure. Do not move the machine without normal air pressure.
In an emergency, the machine can be moved with the parking/emergency brake applied, with the engine running, by holding the shift lever in 1st speed. The lever and transmission will return to NEUTRAL immediately when the lever is released.
Moving the machine with the parking/emergency brake applied can cause excessive wear or damage to the brake. If necessary, have the brake repaired before operating the machine.
Loss of brake oil or air pressure will cause the brake indicators on the operator panel to light up. The emergency brake will automatically engage and stop the machine. The fault light will also flash when the monitor system lights go on.Test Emergency Braking System:
Be sure that the area around the machine is clear of personnel and obstructions.Be sure the antipivot link is in the carry position.Test the brakes on a dry, level surface.Fasten the seat belt before testing the brakes.
1. Start the engine and raise the bucket slightly. 2. With the parking brake applied, shift the transmission to 3rd gear forward.It will be necessary to hold the lever in forward or the lever will move to NEUTRAL. 3. Gradually increase the engine speed to high idle. The machine must not move.
If the machine begins to move, reduce the engine speed immediately and apply the service brakes.
The parking brake light must come on. The main fault light must flash and the warning horn must sound.
If the machine moved while testing, have your Caterpillar dealer inspect the brake. If necessary, repair the parking brake before returning the machine to operation.
4. Reduce engine speed, shift the transmission to NEUTRAL, lower the bucket to the ground, and stop the engine.Manual Release of Emergency Brake
Do not operate the machine if the brake was applied due to a malfunction of the air system or the brake.Correct any problem before attempting to operate the machine.Block the wheels securely so that the machine cannot
Be sure the area is clear of personnel and obstructions.
5. Move the transmission control to the desired travel direction. Rotate the control to the desired speed. 6. Depress the accelerator pedal.Drive the machine forward for best visibility and control.
For operator safety and comfort and maximum service life of power train components, deceleration and/or braking is recommended before any directional shifts are made.
Emergency Brake System
If the brake system air pressure drops below normal operating pressure, a warning horn will sound. The low brake pressure and the parking brake indicators on the operator's panel will light up. The fault light will start flashing.If the pressure drops further, the parking/emergency brake will apply automatically and the transmission will shift to neutral.Be prepared for a sudden stop. Correct the reason for the loss of air pressure. Do not move the machine without normal air pressure.
In an emergency, the machine can be moved with the parking/emergency brake applied, with the engine running, by holding the shift lever in 1st speed. The lever and transmission will return to NEUTRAL immediately when the lever is released.
Moving the machine with the parking/emergency brake applied can cause excessive wear or damage to the brake. If necessary, have the brake repaired before operating the machine.
Loss of brake oil or air pressure will cause the brake indicators on the operator panel to light up. The emergency brake will automatically engage and stop the machine. The fault light will also flash when the monitor system lights go on.Test Emergency Braking System:
Be sure that the area around the machine is clear of personnel and obstructions.Be sure the antipivot link is in the carry position.Test the brakes on a dry, level surface.Fasten the seat belt before testing the brakes.
1. Start the engine and raise the bucket slightly. 2. With the parking brake applied, shift the transmission to 3rd gear forward.It will be necessary to hold the lever in forward or the lever will move to NEUTRAL. 3. Gradually increase the engine speed to high idle. The machine must not move.
If the machine begins to move, reduce the engine speed immediately and apply the service brakes.
The parking brake light must come on. The main fault light must flash and the warning horn must sound.
If the machine moved while testing, have your Caterpillar dealer inspect the brake. If necessary, repair the parking brake before returning the machine to operation.
4. Reduce engine speed, shift the transmission to NEUTRAL, lower the bucket to the ground, and stop the engine.Manual Release of Emergency Brake
Do not operate the machine if the brake was applied due to a malfunction of the air system or the brake.Correct any problem before attempting to operate the machine.Block the wheels securely so that the machine cannot
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
247, 247B, 267, 267B, 287
247, 247B, 257B, 267, 267B, 287
205B, 216, 228, 236, 236B, 236B3, 242B3, 246C, 247, 248, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C...
216, 228, 236, 236B, 236B3, 242B3, 246C, 247, 248, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 3054...
12H, 12H NA, 140H, 140H NA, 236, 236B, 24H, 24M, 252B, 252B3, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D XHP, 287, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D XHP, 30/30, 315C, 3...
236, 236B, 246C, 246D, 252B, 252B3, 256C, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D X...
267, 267B, 287, 906H, 906H2, 907H, 907H2, 908H, 908H2, AP1000E, AP1055E, BG1000E, BG1055E, CB-434B, CB-434C, CB-434D, CB-44B, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB-634D, CD-54, CD-54B,...
267, 267B, 287
120H, 12H NA, 140H NA, 14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 216, 232B, 242B, 242B3, 242D, 247, 247B, 257B, 257B3, 257D, 259B3, 259D, 3P, 3S, 621H, 621K, 627B, 627E, 627F, 627G, 627H, 627K, 62...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906, 906H, 907H, 908H, C3.4
3073074
BEARING-ROLLER
216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 247B, 247B3, 252B, 252B3, 257B, 257B3, 259B3, 267B, 268B, CS-54B
216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 242B, 242B3, 247B, 247B3, 252B, 252B3, 257B, 257B3, 259B3, 267B, 268B, CS-54B
2303755
BEARING-SLEEVE
267B, 287
267B, 287
236, 236B, 246C, 246D, 252B, 252B3, 256C, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D X...
0813698
BEARING
216, 216B, 216B3, 236, 236B, 236B3, 242B, 242B3, 247, 252B, 252B3, 257B3, 259B3, 267B, 268B, 904B, 904H, CB-434D, CB-44B, CB-521, CB-525B, CB-534, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB...
216, 216B, 216B3, 236, 236B, 236B3, 242B, 242B3, 247, 252B, 252B3, 257B3, 259B3, 267B, 268B, 904B, 904H, CB-434D, CB-44B, CB-521, CB-525B, CB-534, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB...
1413049
BEARING
236, 236B, 236B3, 247, 247B, 248, 252B, 252B3, 267, 267B, 268B, 287, AP-600D, AP1000E, BG-260D, BG1000E, BG500E, BG600D, CB-334D, CB-334E, CB-335D, CB-545
236, 236B, 236B3, 247, 247B, 248, 252B, 252B3, 267, 267B, 268B, 287, AP-600D, AP1000E, BG-260D, BG1000E, BG500E, BG600D, CB-334D, CB-334E, CB-335D, CB-545
236, 236B, 236B3, 248, 252B, 252B3, 268B
1641231
BEARING
416D, 420D, 424D, 428D, 432D, 438D, 442D
416D, 420D, 424D, 428D, 432D, 438D, 442D
1834934
BEARING-SELF-ALIGNING
420D, 420E, 420F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 442D, 442E, 444E, 444F, 446D, 450E, 450F
420D, 420E, 420F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 442D, 442E, 444E, 444F, 446D, 450E, 450F
2108238
BEARING
TH210, TH215
TH210, TH215
2093038
BEARING
TH210, TH215
TH210, TH215
267, 267B, 287
267, 267B, 287, 906H, 906H2, 907H, 907H2, 908H, 908H2, AP1000E, AP1055E, BG1000E, BG1055E, CB-434D, CB-44B, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB-634D, CB-64, CD-54, CD-54B, CP-533E, C...
267, 267B, 287, 906H, 906H2, 907H, 907H2, 908H, 908H2, AP1000E, AP1055E, BG1000E, BG1055E, CB-434B, CB-434C, CB-434D, CB-44B, CB-534C, CB-534D, CB-54, CB-54B, CB-564D, CB-634C, CB-634D, CD-54, CD-54B,...
2681941
BEARING-TAPERED ROLLER
267, 267B, 287, AP-600D, AP1000E, BG-260D, BG1000E, BG500E, BG600D
267, 267B, 287, AP-600D, AP1000E, BG-260D, BG1000E, BG500E, BG600D