1P0011 BEARING Caterpillar parts
16, 631C, 769, 824B, 988, D343, G343
Rating:
Alternative (cross code) number:
CA1P0011
1P-0011
1P0011
CA1P0011
1P-0011
1P0011
Weight: 0.30 pounds 0 kg.
GAS ENGINE, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$32.45
26 Jan 2020
0.348550836222[0.00] Poun
-: -
Twbestest 1P-0011 Test Leads (Silicone) with 20Amps Alligator Clips(Threaded Slide-on) and10Amps Alligator Clips(Threaded Slide-on) with Flexible Boots
Test lead set connects a compatible electrical test meter to a device for testing Cat III, 1000 volt, Cat IV, 600 volt, 10 amps || Set includes two lead wires with threaded test probe tips, two large alligator clips and two insulated slide-on alligator clip set with flexible boots (Santoprenen rubber) || Threaded alligator clips with teeth that grip the conductor to provide a more secure, hands-free connection than probe tips || Push-on alligator clips have 2mm banana plug adapter for connecting to 2mm probe leads || 35" (0.9 meter) test leads with right-angle shrouded banana plugs, distinctive comfort grip probes, double insulated silicone leads(UL3239)
Test lead set connects a compatible electrical test meter to a device for testing Cat III, 1000 volt, Cat IV, 600 volt, 10 amps || Set includes two lead wires with threaded test probe tips, two large alligator clips and two insulated slide-on alligator clip set with flexible boots (Santoprenen rubber) || Threaded alligator clips with teeth that grip the conductor to provide a more secure, hands-free connection than probe tips || Push-on alligator clips have 2mm banana plug adapter for connecting to 2mm probe leads || 35" (0.9 meter) test leads with right-angle shrouded banana plugs, distinctive comfort grip probes, double insulated silicone leads(UL3239)
Number on catalog scheme:
None
For full view, you need register
Compatible equipment models: 1P0011:
Information:
Static Switch Description
Illustration 1 g01277605
(1) Static switch
Illustration 2 g01277585
Static switch assembly
(2) Heat sink and shroud
(3) Snubber assembly
(4) Static switch interface board
(5) Static switch module Note: There are three snubber assemblies and three static switch modules.The static switch assembly (1) is composed of three thyristor modules. One module is connected to each of the input phases. Each module has two devices. In the system, the devices are connected in parallel. However, the devices are connected in opposite directions. The following functions are functions of the static switch:
Isolation of the input node during a discharge
Synchronization of the signals of the inverter node to the signals of the input node upon restoration of the input signals after an outage
Initial charge of the DC busThe following information applies to all three of the phases.
Only one of the parallel thyristors is turned on at a time.
The thyristors only conduct current when the thyristors are forward biased. Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge
Illustration 1 g01277605
(1) Static switch
Illustration 2 g01277585
Static switch assembly
(2) Heat sink and shroud
(3) Snubber assembly
(4) Static switch interface board
(5) Static switch module Note: There are three snubber assemblies and three static switch modules.The static switch assembly (1) is composed of three thyristor modules. One module is connected to each of the input phases. Each module has two devices. In the system, the devices are connected in parallel. However, the devices are connected in opposite directions. The following functions are functions of the static switch:
Isolation of the input node during a discharge
Synchronization of the signals of the inverter node to the signals of the input node upon restoration of the input signals after an outage
Initial charge of the DC busThe following information applies to all three of the phases.
Only one of the parallel thyristors is turned on at a time.
The thyristors only conduct current when the thyristors are forward biased. Removal Procedure
Refer to Systems Operation, Testing and Adjusting, UENR3954, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in a static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge
Cat SIS web machinery list:
Parts bearing Caterpillar catalog:
966C, 966R, 988
980B, 988
980, 980B, 988
69D, 768B, 768C, 769, 769C, 769D, 770, 770G, 771C, 771D, 772, 772B, 772G, 772G OEM, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 775B, 775D, 775E, 775F, 775G, 775G LRC, AD30, AD40, AD45, AD45B, AD55, ...
12E, 16, 769, 772, 773
16, 768B, 769, 769C, 772, 773, 773B
16, 768B, 769, 772, 773, D550B
69D, 768B, 769, 769C
824B, 824C, 826C, 834B, 836
14E, 16
14E, 16
14E, 16
3306, 769, D333B, D342, D342C
8S2738
BEARING
D398
D398
8S2736
BEARING GROUP
D398
D398
5M1786
BEARING
651, 657, D337, D337F, D342C, D343, D353C, D397D, D8H, D9E, D9G
651, 657, D337, D337F, D342C, D343, D353C, D397D, D8H, D9E, D9G
4L7836
BEARING
D342C, D343, D348, D349, D353C, D379A, D398, D399
D342C, D343, D348, D349, D353C, D379A, D398, D399
D342C, D8H
4M9428
BEARING ASSEM.
12E, 977H, D8H, D9E
12E, 977H, D8H, D9E
3306, 631C, 641B, 772, D348, D379B, G3304, G3306
9S2245
BEARING
D342, D342C, D8H
D342, D342C, D8H
9M4876
BEARING
594, D353C, D9H
594, D353C, D9H
594, D353C, D9H
594, D353C, D9E, D9G, D9H