2582306 BEARING-SLEEVE Caterpillar parts
D6R, D6R II
Rating:
Alternative (cross code) number:
CA2582306
258-2306
2582306
CA2582306
258-2306
2582306
Weight: 0.73 pounds 0 kg.
TRACK-TYPE TRACTOR,
Information:
Start By:
Remove the valve lifter groups. Refer to Disassembly and Assembly, "Valve Lifter - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00575670
Illustration 2 g00643307
Earlier
Illustration 3 g00643309
Later
Remove the camshaft inspection covers from the side of the cylinder block. Note: The engine must be rotated in order to remove all of the bolts that hold camshaft segment (4) in position.
Use Tooling (B) in order to loosen bolts (1) on the outside of camshaft segment (4).
If it is necessary to remove camshaft journal (2), loosen bolts (3) on the outside diameter.
Rotate the engine until bolts (1) and bolts (3) that were toward the inside of the cylinder block are on the outside.
Loosen remaining bolts (1) and bolts (3).
Illustration 4 g00615465
Earlier
Illustration 5 g00643310
Later
Note: The engine cannot be rotated after camshaft drive gear (5) is removed. Be sure that all of the necessary bolts have been loosened before the camshaft drive gear is removed.
Remove camshaft drive gear (5), if camshaft drive shaft assembly (6) will be removed.
Illustration 6 g01301387
Engage and lock the manual barring group in order to prevent the rotation of the crankshaft when bolt (8) is loosened. Note: In order to prevent damage to the camshaft timing pins, be sure to remove the pins when bolt (8) is loosened.
Use Tooling (C) and loosen bolt (8) on each camshaft.
Remove bolt (8) and washer (9).
Remove bolts (7) and plate (10) from camshaft drive gear (5).
Place washer (9) in position between the camshaft and plate (10). This position is shown in Illustration 6. Install bolt (8).
Install bolts (7) hand tight. Note: Be sure that bolt (8) is installed. This installation will prevent the camshaft drive gears from falling as the gears are loosened from the taper on the camshaft.
Tighten bolts (7) evenly in order to loosen camshaft drive gear (5) from the taper on the camshaft.
Attach a suitable lifting device to camshaft drive gear (5). The weight of camshaft drive gear (5) is approximately 35 kg (77 lb). Remove bolt (8).
Remove bolts (7) from plate (10) and washer (9).
Remove camshaft drive gear (5) from the rear housing.
Illustration 7 g00643311
Earlier camshaft segments
Illustration 8 g00643312
Later camshaft segments
Note: Identify the proper orientation of the camshaft segments and the camshaft journals for installation purposes.
Install Tooling (A) under camshaft segment (4).
Remove bolts (1) that hold the camshaft segment in position.
Carefully move the front section of the camshaft toward the front of the engine. This is done in order to disengage the dowels in each end of the camshaft segment.
Carefully move camshaft segment (4) out of the engine on Tooling (A).
Attach a suitable lifting device to camshaft segment (4). The weight of camshaft segment (4) is approximately 30 kg (66 lb). Remove the camshaft segment from Tooling (A). Put identification marks on the camshaft segment for proper installation.
Remove the spacers from each camshaft journal. Remove Tooling (A) from the engine. Note: Later camshaft segments do not have spacers.
Remove bolts (3) that hold camshaft journal (2) to the other camshaft segment. Note: Later camshaft segments do not have spacers.
Slide camshaft journal
Remove the valve lifter groups. Refer to Disassembly and Assembly, "Valve Lifter - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00575670
Illustration 2 g00643307
Earlier
Illustration 3 g00643309
Later
Remove the camshaft inspection covers from the side of the cylinder block. Note: The engine must be rotated in order to remove all of the bolts that hold camshaft segment (4) in position.
Use Tooling (B) in order to loosen bolts (1) on the outside of camshaft segment (4).
If it is necessary to remove camshaft journal (2), loosen bolts (3) on the outside diameter.
Rotate the engine until bolts (1) and bolts (3) that were toward the inside of the cylinder block are on the outside.
Loosen remaining bolts (1) and bolts (3).
Illustration 4 g00615465
Earlier
Illustration 5 g00643310
Later
Note: The engine cannot be rotated after camshaft drive gear (5) is removed. Be sure that all of the necessary bolts have been loosened before the camshaft drive gear is removed.
Remove camshaft drive gear (5), if camshaft drive shaft assembly (6) will be removed.
Illustration 6 g01301387
Engage and lock the manual barring group in order to prevent the rotation of the crankshaft when bolt (8) is loosened. Note: In order to prevent damage to the camshaft timing pins, be sure to remove the pins when bolt (8) is loosened.
Use Tooling (C) and loosen bolt (8) on each camshaft.
Remove bolt (8) and washer (9).
Remove bolts (7) and plate (10) from camshaft drive gear (5).
Place washer (9) in position between the camshaft and plate (10). This position is shown in Illustration 6. Install bolt (8).
Install bolts (7) hand tight. Note: Be sure that bolt (8) is installed. This installation will prevent the camshaft drive gears from falling as the gears are loosened from the taper on the camshaft.
Tighten bolts (7) evenly in order to loosen camshaft drive gear (5) from the taper on the camshaft.
Attach a suitable lifting device to camshaft drive gear (5). The weight of camshaft drive gear (5) is approximately 35 kg (77 lb). Remove bolt (8).
Remove bolts (7) from plate (10) and washer (9).
Remove camshaft drive gear (5) from the rear housing.
Illustration 7 g00643311
Earlier camshaft segments
Illustration 8 g00643312
Later camshaft segments
Note: Identify the proper orientation of the camshaft segments and the camshaft journals for installation purposes.
Install Tooling (A) under camshaft segment (4).
Remove bolts (1) that hold the camshaft segment in position.
Carefully move the front section of the camshaft toward the front of the engine. This is done in order to disengage the dowels in each end of the camshaft segment.
Carefully move camshaft segment (4) out of the engine on Tooling (A).
Attach a suitable lifting device to camshaft segment (4). The weight of camshaft segment (4) is approximately 30 kg (66 lb). Remove the camshaft segment from Tooling (A). Put identification marks on the camshaft segment for proper installation.
Remove the spacers from each camshaft journal. Remove Tooling (A) from the engine. Note: Later camshaft segments do not have spacers.
Remove bolts (3) that hold camshaft journal (2) to the other camshaft segment. Note: Later camshaft segments do not have spacers.
Slide camshaft journal
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
4S8538
BEARING-SPECIAL BALL
517, 527, 561M, 561N, 572R, 572R II, 583R, 587R, 587T, 814, 815, 910, 916, 926, 931B, 931C, 931C II, 933, 939, 950, 955K, 955L, 966C, D3B, D3C III, D4B, D4C, D4C III, D4H, D4H XL, D4HTSK II, D4HTSK II...
517, 527, 561M, 561N, 572R, 572R II, 583R, 587R, 587T, 814, 815, 910, 916, 926, 931B, 931C, 931C II, 933, 939, 950, 955K, 955L, 966C, D3B, D3C III, D4B, D4C, D4C III, D4H, D4H XL, D4HTSK II, D4HTSK II...
1T0902
BEARING-SLEEVE
572G, 572R, 572R II, 578, 583R, 587R, 587T, 955K, 955L, D6C, D6D, D6E, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7G2, D7H, D7R...
572G, 572R, 572R II, 578, 583R, 587R, 587T, 955K, 955L, D6C, D6D, D6E, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7G2, D7H, D7R...
1T0441
BEARING-BALL
572G, 572R, 572R II, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR, PF-300C, PS-...
572G, 572R, 572R II, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR, PF-300C, PS-...
0054834
BEARING AS-TAPERED ROLLER
515, 518C, 525, 528B, 530B, 583T, 936, 936F, 938F, 938G, 938G II, 938H, 938K, AP-800C, AP-800D, CS-643, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T,...
515, 518C, 525, 528B, 530B, 583T, 936, 936F, 938F, 938G, 938G II, 938H, 938K, AP-800C, AP-800D, CS-643, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T,...
6V0855
BEARING AS-TAPERED ROLLER
583T, 611, 615, 615C, 651E, 657E, 814B, 815B, 816B, 936, 943, 950B, 950B/950E, 966C, 966D, 966F, 966G, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, ...
583T, 611, 615, 615C, 651E, 657E, 814B, 815B, 816B, 936, 943, 950B, 950B/950E, 966C, 966D, 966F, 966G, D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D6R STD, D6T, ...
1003402
BEARING-SWASH
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
1003405
BEARING-SWASH
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12H, 12H ES, 12H NA, 12K, 12M, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, 24H, 824G...
7T9586
BEARING
D6H, D6H XL, D6H XR, D6R, D6R II
D6H, D6H XL, D6H XR, D6R, D6R II
1045361
BEARING-SLEEVE
561M, 561N, 572R, 572R II, 583R, 587R, 587T, D5M, D5N, D6M, D6N, D6R, D6R II, D7R, D7R II, PL87
561M, 561N, 572R, 572R II, 583R, 587R, 587T, D5M, D5N, D6M, D6N, D6R, D6R II, D7R, D7R II, PL87
1310825
BEARING-SLEEVE
572R, 572R II, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II
572R, 572R II, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II
1M3909
BEARING-SLEEVE
14E, 14M, 16M, 572R, 572R II, 583T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637D, 637E, 637G, 769, 769C, 769D, 770, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 7...
14E, 14M, 16M, 572R, 572R II, 583T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637D, 637E, 637G, 769, 769C, 769D, 770, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 7...
1799579
BEARING
583R, D6D, D6E, D6G, D6H XR, D6R, D6R II, D7H, D7R, D8R
583R, D6D, D6E, D6G, D6H XR, D6R, D6R II, D7H, D7R, D8R
6P0593
BEARING-ROLLER
578, 583R, 587R, 589, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 918F, 924F, 926, 938F, 950F, 950F II, ...
578, 583R, 587R, 589, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 918F, 924F, 926, 938F, 950F, 950F II, ...
7P8753
BEARING
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, 930K, 938F, 973, 973C, 973D, IT38G II, IT38H
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, 930K, 938F, 973, 973C, 973D, IT38G II, IT38H
7P3194
BEARING-SLEEVE
924K, 930K, 950K, 962K, 973, 973C, 973D, 986H
924K, 930K, 950K, 962K, 973, 973C, 973D, 986H
3G0222
BEARING-SLEEVE
963, 963B, 963C, 963D, 973, 973C, 973D
963, 963B, 963C, 963D, 973, 973C, 973D
3G0707
BEARING
320D, 324D L, 325B L, 325C, 325D L, 329D L, 973, 973C, 973D, D7E, D7E LGP
320D, 324D L, 325B L, 325C, 325D L, 329D L, 973, 973C, 973D, D7E, D7E LGP
1U3848
BEARING-SLEEVE
973, 973C, 973D
973, 973C, 973D
9G9086
BEARING
943, 953, 953B, 953C, 953D
943, 953, 953B, 953C, 953D
3W8409
BEARING
943, 953, 953B, 953C, 953D
943, 953, 953B, 953C, 953D
7J3216
BEARING
525B, 535B, 545, 572R, 572R II, 623H, 631B, 631D, 631E, 631G, 637D, 637E, 637G, 953, 953C, 953D, D7H, D7R, D7R II, D7R XR
525B, 535B, 545, 572R, 572R II, 623H, 631B, 631D, 631E, 631G, 637D, 637E, 637G, 953, 953C, 953D, D7H, D7R, D7R II, D7R XR
3G2580
BEARING
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 943, 953, 953C, 953D, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 943, 953, 953C, 953D, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
6T8387
BEARING
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, D6H, D6H II, D6H XL...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, D6H, D6H II, D6H XL...
2582307
BEARING-SLEEVE
583T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, PL83
583T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, PL83