2582307 BEARING-SLEEVE Caterpillar parts
583T, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, PL83
Rating:
Alternative (cross code) number:
CA2582307
258-2307
2582307
CA2582307
258-2307
2582307
Weight: 0.36 pounds 0 kg.
Information:
ID
50.275
mm
OD
63.067
mm
WIDTH
19
mm
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$13.04
25 Jul 2023
Amazon.com
CTP 2582307 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
$46.08
19 May 2023
Amazon.com
CTP 2582307 Sleeve Bearing for Heavy Equipment
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
CTP Sleeve Bearing Only || Sold in each || Easy in-and-out fit
Compatible equipment models: 2582307:
Information:
MID 039 CID 0299 FMI 01Conditions Which Generate This Code:
Illustration 1 g01343143
Connections of the shift lever position sensor
This diagnostic code is associated with the shift lever position sensor. The FMI 01 means that the ECM has determined that the signal of the sensor is below the normal range.The output frequency of the position sensor is approximately 500 hertz. The value of the sensor's duty cycle is approximately 50% in the neutral position. The duty cycle of the signal increases as the lever is moved from the neutral position to the forward position. The value of the sensor's duty cycle is approximately 80% 10% in the forward position. The duty cycle of the signal decreases as the lever is moved from the neutral position to the reverse position. The value of the sensor's duty cycle is approximately 20% 10% in the reverse position. The possible causes of this failure are listed below:
The position sensor has failed.
The signal circuit of the sensor is shorted to the ground.
The sensor needs to be calibrated.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0299 FMI 01 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:The transmission will be placed in NEUTRAL until the diagnostic code is cleared.Test Step 1. INSPECT THE SENSOR.
Perform a visual inspection of the sensor, the wiring for the sensor and the hardware that is associated with the sensor. Expected Result:There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.Results:
OK - There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor. Proceed to Test Step 2.
NOT OK - There is apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.Repair: Replace the damaged part.Proceed to Test Step 8.Test Step 2. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a multimeter probe along the voltage supply wire (contact 1).
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact 1 to frame ground. Expected Result:The voltage is 10 DCV.Results:
OK - The voltage is 10 DCV. Proceed to Test Step 3.
NOT OK - The voltage is not 10 DCV. The circuit is open. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK FOR PROPER GROUND AT THE SENSOR.
The machine harness remains connected to the sensor.
Turn the key start switch and the disconnect switch to the OFF position.
Remove the multimeter probe from the voltage supply wire (contact 1).
At the back of the harness connector for the sensor, insert a multimeter probe along
Illustration 1 g01343143
Connections of the shift lever position sensor
This diagnostic code is associated with the shift lever position sensor. The FMI 01 means that the ECM has determined that the signal of the sensor is below the normal range.The output frequency of the position sensor is approximately 500 hertz. The value of the sensor's duty cycle is approximately 50% in the neutral position. The duty cycle of the signal increases as the lever is moved from the neutral position to the forward position. The value of the sensor's duty cycle is approximately 80% 10% in the forward position. The duty cycle of the signal decreases as the lever is moved from the neutral position to the reverse position. The value of the sensor's duty cycle is approximately 20% 10% in the reverse position. The possible causes of this failure are listed below:
The position sensor has failed.
The signal circuit of the sensor is shorted to the ground.
The sensor needs to be calibrated.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0299 FMI 01 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:The transmission will be placed in NEUTRAL until the diagnostic code is cleared.Test Step 1. INSPECT THE SENSOR.
Perform a visual inspection of the sensor, the wiring for the sensor and the hardware that is associated with the sensor. Expected Result:There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.Results:
OK - There is no apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor. Proceed to Test Step 2.
NOT OK - There is apparent damage to the sensor, the wiring for the sensor or the hardware that is associated with the sensor.Repair: Replace the damaged part.Proceed to Test Step 8.Test Step 2. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
At the back of the harness connector for the sensor, insert a multimeter probe along the voltage supply wire (contact 1).
Turn the key start switch and the disconnect switch to the ON position.
Measure the voltage from contact 1 to frame ground. Expected Result:The voltage is 10 DCV.Results:
OK - The voltage is 10 DCV. Proceed to Test Step 3.
NOT OK - The voltage is not 10 DCV. The circuit is open. Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK FOR PROPER GROUND AT THE SENSOR.
The machine harness remains connected to the sensor.
Turn the key start switch and the disconnect switch to the OFF position.
Remove the multimeter probe from the voltage supply wire (contact 1).
At the back of the harness connector for the sensor, insert a multimeter probe along
Cat SIS web machinery list:
Parts bearing Caterpillar catalog:
1M3909
BEARING-SLEEVE
14E, 14M, 16M, 572R, 572R II, 583T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637D, 637E, 637G, 769, 769C, 769D, 770, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 7...
14E, 14M, 16M, 572R, 572R II, 583T, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637D, 637E, 637G, 769, 769C, 769D, 770, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 7...
1799579
BEARING
583R, D6D, D6E, D6G, D6H XR, D6R, D6R II, D7H, D7R, D8R
583R, D6D, D6E, D6G, D6H XR, D6R, D6R II, D7H, D7R, D8R
9J3206
BEARING-SPHERICAL
2470C, 2570C, 2670C, 2864C, 517, 525, 525B, 527, 533, 543, 553C, 563C, 573C, 583R, 583T, 584, 586C, 587R, 587T, 613, 613B, 613C, 613C II, 613G, BR624, D250B, D250D, D250E, D250E II, D300B, D300D, D300...
2470C, 2570C, 2670C, 2864C, 517, 525, 525B, 527, 533, 543, 553C, 563C, 573C, 583R, 583T, 584, 586C, 587R, 587T, 613, 613B, 613C, 613C II, 613G, BR624, D250B, D250D, D250E, D250E II, D300B, D300D, D300...
7G7379
BEARING
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
572R, 572R II, 583R, 583T, 587R, 587T, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
1543298
BEARING-SLEEVE
583R, 583T, 587R, 587T, D8N, D8R, D8R II, D8T, PL83, PL87
583R, 583T, 587R, 587T, D8N, D8R, D8R II, D8T, PL83, PL87
6E4374
BEARING
583T, 587R, 587T, 621F, 621G, 627F, 627G, 631G, 637G, 963D, 973C, D7E, D7E LGP, D8N, D8R, D8R II, D8T, HA771, HA871, PL83, PL87, TK371, TK381
583T, 587R, 587T, 621F, 621G, 627F, 627G, 631G, 637G, 963D, 973C, D7E, D7E LGP, D8N, D8R, D8R II, D8T, HA771, HA871, PL83, PL87, TK371, TK381
1917583
BEARING AS-ROLLER
120H, 120M, 120M 2, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16H, 2470C, 2570C, 2670C, 330C, 330C ...
120H, 120M, 120M 2, 12H, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 140H, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14H, 14M, 160H, 160M, 160M 2, 160M 3, 160M 3 AWD, 163H, 16H, 2470C, 2570C, 2670C, 330C, 330C ...
1559125
BEARING AS-ROLLER
120H, 120M, 12H, 12M, 135H, 140H, 140M, 143H, 14H, 14M, 160H, 160M, 163H, 16H, 2470C, 2570C, 2670C, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D...
120H, 120M, 12H, 12M, 135H, 140H, 140M, 143H, 14H, 14M, 160H, 160M, 163H, 16H, 2470C, 2570C, 2670C, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D...
1051642
BEARING
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
365B, 365B II, 735, 735B, 740, 740B, 776D, 777D, 777F, 777G, 834K, 836K, 844, 924K, 930K, 938K, 950 GC, 950H, 962H, 963D, 973D, 986H, 990, 990 II, 993K, D10T, D10T2, D11T, D350E II, D400E II, D6T, D6T...
1051648
BEARING
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 365B, 365B II, 554, 621K, 623K, 623K LRC, 627K, 627K LRC, 735, 735B, 740, 740B, 776D, 77...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 365B, 365B II, 554, 621K, 623K, 623K LRC, 627K, 627K LRC, 735, 735B, 740, 740B, 776D, 77...
3G2579
BEARING
120K, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
120K, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 160H, 160H ES, 160H NA, 160K, 160M, 163H, 163H NA, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
3D2546
BEARING ASSEM.
12F, 14E, 561C, 571G, 650B, 666, 666B, D6R III, D7R II
12F, 14E, 561C, 571G, 650B, 666, 666B, D6R III, D7R II
2582306
BEARING-SLEEVE
D6R, D6R II
D6R, D6R II
6P0593
BEARING-ROLLER
578, 583R, 587R, 589, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 918F, 924F, 926, 938F, 950F, 950F II, ...
578, 583R, 587R, 589, 814B, 814F, 815B, 815F, 816B, 816F, 824C, 824G, 824G II, 824H, 825C, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 834B, 836, 836G, 836H, 918F, 924F, 926, 938F, 950F, 950F II, ...
7P8753
BEARING
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, 930K, 938F, 973, 973C, 973D, IT38G II, IT38H
924G, 924GZ, 924H, 924HZ, 928HZ, 930G, 930K, 938F, 973, 973C, 973D, IT38G II, IT38H
7P3194
BEARING-SLEEVE
924K, 930K, 950K, 962K, 973, 973C, 973D, 986H
924K, 930K, 950K, 962K, 973, 973C, 973D, 986H
3G0222
BEARING-SLEEVE
963, 963B, 963C, 963D, 973, 973C, 973D
963, 963B, 963C, 963D, 973, 973C, 973D
3G0707
BEARING
320D, 324D L, 325B L, 325C, 325D L, 329D L, 973, 973C, 973D, D7E, D7E LGP
320D, 324D L, 325B L, 325C, 325D L, 329D L, 973, 973C, 973D, D7E, D7E LGP
2679554
BEARING
824K, 825K, 826K, 834K, 836K, 844K, 854K, 950K, 953D, 962K, 963D, 966H, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 973D, 980K, 980K HLG, 980M, 982M, 988K, 990K, 992K, 993K, 994H, D3K XL, D4K XL, D5K LG...
824K, 825K, 826K, 834K, 836K, 844K, 854K, 950K, 953D, 962K, 963D, 966H, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 973D, 980K, 980K HLG, 980M, 982M, 988K, 990K, 992K, 993K, 994H, D3K XL, D4K XL, D5K LG...
9G9086
BEARING
943, 953, 953B, 953C, 953D
943, 953, 953B, 953C, 953D
3W8409
BEARING
943, 953, 953B, 953C, 953D
943, 953, 953B, 953C, 953D
7J3216
BEARING
525B, 535B, 545, 572R, 572R II, 623H, 631B, 631D, 631E, 631G, 637D, 637E, 637G, 953, 953C, 953D, D7H, D7R, D7R II, D7R XR
525B, 535B, 545, 572R, 572R II, 623H, 631B, 631D, 631E, 631G, 637D, 637E, 637G, 953, 953C, 953D, D7H, D7R, D7R II, D7R XR
3G2580
BEARING
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 943, 953, 953C, 953D, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 943, 953, 953C, 953D, D6R, D6R STD, D6T, D6T LGP, D6T LGPPAT
6T8387
BEARING
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, D6H, D6H II, D6H XL...
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP1000E, AP1055E, AP555E, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, BG655D, D6H, D6H II, D6H XL...