2642768 BEARING Caterpillar parts
Rating:
Alternative (cross code) number:
CA2642768
264-2768
2642768
CA2642768
264-2768
2642768
Weight: 0.28 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
SKSKSKFF Replacement for Compatible with 2642768 Bearing-Cone Fits Caterpillar Models
SKSKSKFF
SKSKSKFF
CTP 2642768 Cone Bearing for Heavy Equipment
CTP Cone Bearing Only || Sold in each || Easy in-and-out fit
CTP Cone Bearing Only || Sold in each || Easy in-and-out fit
Information:
Procedure
Illustration 1 g00592279
Display Area Of The Caterpillar Monitoring System
The display area is showing the following diagnostic code: MID 082, CID 0353 and FMI 01
(4) First display. (5) Module identifier (MID). (6) Diagnostic code indicator. (7) Second display. (8) Component identifier (CID). (9) Failure mode identifier (FMI).
Use the following procedure to troubleshoot the diagnostic code information. Connect the 4C-8195 Control Service Tool to the service connector that is located behind the access panel in the right rear of the cab.
Place the Caterpillar Monitoring System in service mode (mode 3). In order to place the Caterpillar Monitoring System in service mode, press and hold the mode switch of the control service tool. Release the mode switch when "-3-" is shown on the display. Note: The diagnostic scrolling mode may be entered in order to see the diagnostic codes, but the diagnostic codes can be more easily diagnosed by using the service mode. The service mode allows the diagnostic codes to be placed on hold for further investigation. The service mode also allows the diagnostic codes to be cleared when the problem has been fixed.
A diagnostic code is displayed and the diagnostic code is on hold at this time. The display toggles between showing MID (5) and CID (8) and FMI (9). When you are in the service mode and there are no diagnostic codes, screen (4) shows "---" only.
In order to view all the diagnostic codes, scroll through the diagnostic codes. In order to scroll through the diagnostic codes, press and hold the scroll switch of the control service tool. The display momentarily shows MID (5), CID (8) and FMI (9) for each diagnostic code. The word "End" is shown after the last diagnostic code in the list.
Place the desired diagnostic code on hold. In order to place the diagnostic code on hold, release the scroll switch when the desired diagnostic code is shown.
The MID will indicate the ECM that is generating the diagnostic code. If the MID is not 082, use Table 1 in order to determine the ECM that has detected the fault. Then refer to the service manual module for that electronic control.
Table 1
Reference Material
MID Description Service Manual Module
030 Caterpillar Monitoring System Systems Operation/Testing and Adjusting, "Caterpillar Monitoring System"
036 Engine ECM Troubleshooting Guide, "Engine"
081 Power Train ECM Systems Operation/Testing and Adjusting, "Power Train"
082 Implement ECM Systems Operation/Testing and Adjusting, "Hydraulic System"
122 Product Link Systems Operation/Testing and Adjusting, "Product Link 121/321"
Observe diagnostic code indicator (6). In service mode, the diagnostic code indicator functions as a fault present indicator.
If diagnostic code indicator (6) shows "SERV CODE", then the fault that caused the diagnostic code that is shown is currently present.
If diagnostic code indicator (6) is OFF, then the fault that caused the diagnostic code that is shown is not present at this time.
Refer to the test procedure in Troubleshooting and Testing and Adjusting in order to troubleshoot the diagnostic code.
After a diagnostic code is corrected, clear the diagnostic code. In order to clear the diagnostic code, momentarily press the
Illustration 1 g00592279
Display Area Of The Caterpillar Monitoring System
The display area is showing the following diagnostic code: MID 082, CID 0353 and FMI 01
(4) First display. (5) Module identifier (MID). (6) Diagnostic code indicator. (7) Second display. (8) Component identifier (CID). (9) Failure mode identifier (FMI).
Use the following procedure to troubleshoot the diagnostic code information. Connect the 4C-8195 Control Service Tool to the service connector that is located behind the access panel in the right rear of the cab.
Place the Caterpillar Monitoring System in service mode (mode 3). In order to place the Caterpillar Monitoring System in service mode, press and hold the mode switch of the control service tool. Release the mode switch when "-3-" is shown on the display. Note: The diagnostic scrolling mode may be entered in order to see the diagnostic codes, but the diagnostic codes can be more easily diagnosed by using the service mode. The service mode allows the diagnostic codes to be placed on hold for further investigation. The service mode also allows the diagnostic codes to be cleared when the problem has been fixed.
A diagnostic code is displayed and the diagnostic code is on hold at this time. The display toggles between showing MID (5) and CID (8) and FMI (9). When you are in the service mode and there are no diagnostic codes, screen (4) shows "---" only.
In order to view all the diagnostic codes, scroll through the diagnostic codes. In order to scroll through the diagnostic codes, press and hold the scroll switch of the control service tool. The display momentarily shows MID (5), CID (8) and FMI (9) for each diagnostic code. The word "End" is shown after the last diagnostic code in the list.
Place the desired diagnostic code on hold. In order to place the diagnostic code on hold, release the scroll switch when the desired diagnostic code is shown.
The MID will indicate the ECM that is generating the diagnostic code. If the MID is not 082, use Table 1 in order to determine the ECM that has detected the fault. Then refer to the service manual module for that electronic control.
Table 1
Reference Material
MID Description Service Manual Module
030 Caterpillar Monitoring System Systems Operation/Testing and Adjusting, "Caterpillar Monitoring System"
036 Engine ECM Troubleshooting Guide, "Engine"
081 Power Train ECM Systems Operation/Testing and Adjusting, "Power Train"
082 Implement ECM Systems Operation/Testing and Adjusting, "Hydraulic System"
122 Product Link Systems Operation/Testing and Adjusting, "Product Link 121/321"
Observe diagnostic code indicator (6). In service mode, the diagnostic code indicator functions as a fault present indicator.
If diagnostic code indicator (6) shows "SERV CODE", then the fault that caused the diagnostic code that is shown is currently present.
If diagnostic code indicator (6) is OFF, then the fault that caused the diagnostic code that is shown is not present at this time.
Refer to the test procedure in Troubleshooting and Testing and Adjusting in order to troubleshoot the diagnostic code.
After a diagnostic code is corrected, clear the diagnostic code. In order to clear the diagnostic code, momentarily press the
Caterpillar parts catalog:
Parts bearing Caterpillar catalog:
5551699
BEARING-ALIGNING
Caterpillar
Caterpillar
5386267
BEARING-CONE
Caterpillar
Caterpillar
5099175
BEARING-SLEEVE
Caterpillar
Caterpillar
5079061
BEARING-TAPERED
Caterpillar
Caterpillar
5014311
BEARING-CONE
Caterpillar
Caterpillar
5014310
BEARING-CUP
Caterpillar
Caterpillar
4385164
BEARING-TAPERED ROLLER
Caterpillar
Caterpillar
4259210
BEARING
Caterpillar
Caterpillar
4186128
BEARING-NEEDLE
Caterpillar
Caterpillar
3624859
BEARING
Caterpillar
Caterpillar
3025841
BEARING
Caterpillar
Caterpillar
2642769
BEARING
Caterpillar
Caterpillar